2000 SUZUKI SWIFT Transmission fluid change

MAINTENANCE AND LUBRICATION 0B-3
Interval:
This interval should be
judged by
This table includes services as scheduled up to 90,000 km (54,000 miles)
mileage. Beyond 90,000 km (54,000 miles), carry out the same services at
the same intervals respectively.
This interval should be judged by
odometer reading or months,Km(
1,000)153045607590g
whichever comes first.Miles(
1,000)91827364554
Months122436486072
4. EMISSION CONTROL SYSTEM
4-1.PCV (Positive Crankcase Ventilation)
ValveVehicle
without
O2S
––I––I
Vehicle
with O2S–––––I
4-2.Fuel evaporative emission control system–––––I
5. BRAKE
5-1.Brake discs and padsIIIIII
Brake drums and shoes–I–I–I
5-2.Brake hoses and pipes–I–I–I
5-3.Brake fluid–R–R–R
5-4.Brake lever and cableInspect at first 15,000 km (9,000 miles) only.
6. CHASSIS AND BODY
6-1.Clutch pedal (for manual transmission)–I–I–I
6-2.Tires/wheel discsIIIIII
6-3.Propeller shaft (4WD) and drive shafts––I––I
6-4.Suspension system–I–I–I
6-5.Steering system–I–I–I
6-6.Power steering (if equipped)IIIIII
6-7.Manual transmission oilI–R––R
6-8.Automatic transmissionFluid level–I–I–I
Fluid changeReplace every 165,000 km (99,000 miles).
Fluid hose–––R––
6-9.Rear differential oil (4WD) (R: 1st 15,000 km only)R or I–I–I–
6-10. All latches, hinges and locks–I–I–I
NOTES:

“R”: Replace or change

“I”: Inspect and correct or replace if necessary

0B-4 MAINTENANCE AND LUBRICATION
MAINTENANCE RECOMMENDED UNDER SEVERE DRIVING CONDITIONS
If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is
recommended that applicable maintenance operation be performed at the particular interval as given in the chart
below.
Severe condition code
A –Repeated short trips F –Leaded fuel use
B –Driving on rough and/or muddy roads G –(For Diesel engine) Town use / Towing a trailer /
C –Driving on dusty roads Sustained high speed driving /
D –Driving in extremely cold weather and/or Hot climates above 30C (86F) /
salted roads Low quality lubricants or fuel
E –Repeated short trips in extremely cold weather H –Trailer towing (if admitted)
Severe
Condition Code
MaintenanceMaintenance
OperationMaintenance Interval
BCDITEM 1-1IEvery 15,000 km (9,000 miles)
or 12 months
– B C D – – – –Drive belt (V-rib belt)REvery 45,000 km (27,000 miles)
or 36 months
A – C D E F – HITEM 1-4
Engine oil and filterREvery 5,000 km (3,000 miles)
or 4 months
A B C – E F – HITEM 2-1
Spark plugsREvery 10,000 km (6,000 miles)
or 8 months
ITEM 3 1IEvery 2,500 km (1,500 miles)
– – C – – – – –ITEM 3-1
Air cleaner filter *1REvery 30,000 km (18,000 miles)
or 24 months
– B C D – – – HITEM 6-2
Wheel bearingsIEvery 15,000 km (9,000 miles)
or 12 months
– B – D E – – H
ITEM 6-3
Propeller shaft (4WD) and drive
shafts
I
Every 15,000 km (9,000 miles)
or 12 months
– B – – E – – H
ITEM 6-7 / 6-8
Manual transmission oil and
differential oil (4WD)
R
Every 30,000 km (18,000 miles)
or 24 months
– B – – E – – HITEM 6-9
Automatic transmission fluidREvery 30,000 km (18,000 miles)
or 24 months
NOTES:

“R”: Replace or change

“I”: Inspect and correct or replace if necessary

*1: Inspect or replace more frequently if necessary

1. Oil level gauge
2. FULL HOT mark
3. LOW HOT mark
4. FULL COLD mark
5. LOW COLD mark
1. Drain plug
0B-18 MAINTENANCE AND LUBRICATION
ITEM 6-9
Automatic Transmission
[Fluid level inspection]
1) Inspect transmission case for evidence of fluid leakage.
Repair leaky point, if any.
2) Make sure that vehicle is placed level for fluid level check.
3) Check fluid level.
For fluid level checking procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B and be sure to perform it under specified
conditions. If fluid level is low, replenish specified fluid.
[Fluid change]
1) Perform steps 1) and 2) of above Fluid Level Inspection.
2) Change fluid. For its procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B.
CAUTION:
Use of specified fluid is absolutely necessary.
[Fluid cooler hose change]
Replace inlet and outlet hoses (1) of cooler hose and their clamps.
For replacement procedure, refer to ON-VEHICLE SERVICE in
SECTION 7B.

1. Final gear
2. Differential gear assembly
3. Counter shaft
4. 1st and reverse brake
5. Counter driven gear11. Forward clutch
12. Direct clutch
13. Input shaft
14. Torque converter
15. Oil pump 6. Output shaft
7. Rear planetary gear
8. Front planetary gear
9. Valve body assembly
10. Oil strainer
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-3
GENERAL DESCRIPTION
The automatic transmission consists of the hydraulic torque converter, electronically controlled 3-speed automatic
transmission, countershaft and differential.
The transmission consists of 2 planetary gears, 2 disk clutches, 1 band brake, 1 disk brake and 1 one-way clutch.
Its operation is controlled by selecting a position from 6 positions (P, R, N, D, 2 and L ranges) manually by means
of the selector lever installed on the compartment floor.
In the D or 2 range, the gear ratio is changed for the 1st, 2nd or 3rd speed (D range only) automatically by engine
control module (electronic control).
For the automatic transmission fluid, DEXRON
-

E, DEXRON-


or its equivalent must be used. Lubrication
in the automatic transmission is provided by the oil pump which is operated by the engine revolution. Therefore,
the engine should not be stopped even during coasting to obtain proper lubrication.
When it becomes necessary to be towed, front wheels must be raised so as not to roll them.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-19
Fig. 1 for Step 5. Fig. 2 for Step 5. Fig. 3 for Step 5.
When not using SUZUKI
scan tool:
lever position
Terminal
Selector
AUTOMATIC TRANSMISSION BASIC CHECK
This check is very important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been found in visual inspection. Follow the flow table carefully.
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAG. FLOW TABLE”
performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAG. FLOW
TABLE”.
2Check A / T Fluid.
Warm transmission to normal operating temperature and check
fluid level and contamination referring to “FLUID LEVEL
CHECK” of “ON-VEHICLE SERVICE” in this section.
Is it in good condition?Go to Step 3.Add or change
fluid.
3Check Fluid Pressure Control Cable.
1) Warm up engine to normal operating temperature.
2) Check fluid pressure control cable for play referring to
“FLUID PRESSURE CONTROL CABLE” of “ON-VEHICLE
SERVICE” in this section.
Is it in good condition?Go to Step 4.Adjust.
4Check Select Cable for Adjustment referring to “SELECT
CABLE” of “ON-VEHICLE SERVICE” in this section.
Is it adjusted correctly?Go to Step 5.Adjust.
5Check Transmission Range Sensor (Switch) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C03-3 C03-4 C03-5 C03-14
Go to Step 6.Go to Step 3 of
DTC P0705
Flow Table.
2) Check voltage at terminals C03-3, C03-4, C03-5, C03-14,
C03-15 and C03-16 for G10 engine model (C02-11, C02-12,
C02-14, C02-15, C02-21 and C02-23 for G13 engine
model) respectively with selector lever shifted to each
range. See Fig. 2.
Taking terminal C03-3 for G10 engine model (C02-11 for
G13 engine model) as an example, is battery voltage
indicated only when selector lever is shifted to “2” range and
0 V for other ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?
6Check Engine Idle speed referring to Section 6E1 or 6E2.
Is it in good condition?Go to
“SYMPTOM-TO-
INSPECTION
TABLE” below.Go to Section
6E1 or 6E2.
C03-5
(C02-21)C03-16
(C02-15)C03-4
(C02-12)C03-15
(C02-14)C03-3
(C02-11)C03-14
(C02-23)
PB + V0 V0 V0 V0 V0 V
R0 VB + V0 V0 V0 V0 V
N0 V0 VB + V0 V0 V0 V
D0 V0 V0 VB + V0 V0 V
20 V0 V0 V0 VB + V0 V
L0 V0 V0 V0 V0 VB + V