2000 SUZUKI SWIFT wheel

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-79
8) Install pistons and connecting rods as previously outlined.
9) Install oil pump strainer and oil pan as previously outlined.
10) Install cylinder head assembly to cylinder block as previously
outlined.
11) Install camshaft, crankshaft timing belt pulley, timing belt,
crankshaft pulley, water pump pulley, etc., as previously out-
lined.
12) Install clutch to flywheel (for M / T vehicle). For clutch installa-
tion, refer to “CLUTCH” section.
13) Install engine mountings and brackets.
Refer to tightening torque for INSTALLATION of “ENGINE AS-
SEMBLY” in this section.
14) Install engine with transmission to vehicle as previously out-
lined.

09917-98221
Valve stem seal installer09916-77310
Piston ring compressor09924-17810
Flywheel holder09915-47330
Oil filter wrench
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-81
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
SealantSUZUKI BOND NO.1207C
(99000-31150)
Mating surfaces of cylinder block and oil pan.
SealantSUZUKI BOND NO.1215
(99000-31110)
Mating surfaces of camshaft housings (No.6).

Mating surfaces of CMP sensor case and cylinder
block.

6A1-82 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
TIGHTENING TORQUE SPECIFICATIONS
FASTENING PARTSTIGHTENING TORQUEFASTENING PA R T SN.mkg-mlb-ft
Oil pressure switch131.39.5
Valve adjusting screw lock nuts121.29.0
Cylinder head cover bolts111.18.0
Intake manifold bolts and nuts232.317.0
Timing belt tensioner stud111.18.0
Timing belt tensioner bolt252.518.0
Timing belt cover bolts and nut111.18.0
Exhaust manifold bolts and nuts323.223.5
Crankshaft pulley bolt161.611.5
Crankshaft timing belt pulley bolt13013.094.0
Exhaust pipe nuts and bolts505036 5Exhaust manifold stiffener nut505.036.5
Oil pump strainer bolt and stay bolt111180Oil pan bolts and nuts111.18.0
CKP sensor bolt101.07.5
Oil pan drain plug505.036.0
Oil pump rotor plate screws111180Oil pump case bolts111.18.0
Camshaft housing bolts111180Rocker arm shaft bolts111.18.0
Camshaft timing belt pulley bolt606.043.5
Cylinder head venturi plug3.50.352.5
Cylinder head bolts686.849.0
Connecting rod bearing cap nuts353.525.5
Crankshaft main bearing cap bolts545.439.0
Flywheel bolts787.856.5
Drive plate bolts959.569.0
Engine mounting & bracket bolts and nutsRefer to INSTALLATION of
ENGINE ASSEMBLY in this section.

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-9
1. Throttle body
2. Fuel feed hose
NOTE:
Before starting engine, place transmission gear shift lever in
“Neutral” (shift selector lever to “P” range for A/T model), and
set parking brake and block drive wheels.
1) Warm up engine to normal operating temperature.
2) Set tachometer.
3) Check idle speed with A/C OFF.
If idle speed is not within specified range, check idle speed con-
trol system and any other system and parts which might affect
idle speed. Refer to “Engine Diagnosis of Section 6” for inspec-
tion.
Engine idle speed: 850
50 r/min
NOTE:
Idle speed is not adjustable manually. If it is out of its speci-
fied range, there is a faulty condition somewhere. Check
each of related systems and parts.
AIR AND FUEL DELIVERY SYSTEM
FUEL PRESSURE
INSPECTION
1) Relieve fuel pressure, referring to Section 6.
2) Separate air cleaner assembly from throttle body and shift its
position.
3) Disconnect fuel feed hose from throttle body.
CAUTION:
A small amount of fuel may be released after fuel line is
disconnected.
In order to reduce chance of personal injury, cover fitting
to be disconnected with a shop cloth. Place that cloth in
an approved container when disconnection is com-
pleted.
4) Connect special tools and hose between throttle body and fuel
feed pipe as shown in figure, and clamp hoses securely to en-
sure no leaks occur during checking.
Special Tool
(A): 09912-58441
(B): 09912-58431
(C): 09912-58490
5) Install air cleaner assembly to throttle body and cylinder head
cover.

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-17
1. ECM
2. Instrument panel
3. Steering wheel
1. Injector wire
2. Screws
1. Stay
3) Make sure that injector wire O-ring is free from any damage and
deterioration, and apply thin coat of spindle oil or gasoline to O-
ring.
Install injector wire and tighten new wire screw to specified
torque.
Tightening Torque
(a): 3.5 N
.m (0.35 kg-m, 2.5 lb-ft)
4) Connect battery negative cable at battery.
5) With engine “OFF” and ignition switch “ON”, check for fuel leaks.
6) Install air cleaner mounting stay as shown left.
7) Install air cleaner assembly referring to Section 6A.
ELECTRONIC CONTROL SYSTEM
ENGINE CONTROL MODULE (ECM)
CAUTION:
As ECM consists of precision parts, be careful not to ex-
pose it to excessive shock.
REMOVAL
1) Disconnect battery negative cable at battery.
2) Lower fuse box after removing bolt.
3) Disconnect couplers from ECM while releasing coupler lock.
4) Remove ECM from body.
INSTALLATION
1) Install ECM to body.
2) Connect couplers to ECM securely.
3) Install fuse box and tighten its bolt.
4) Connect battery negative cable at battery.

6E1-24 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
VEHICLE SPEED SENSOR (VSS) For M / T
INSPECTION
1) Disconnect negative cable at battery.
2) Remove combination meter from instrument panel.
3) Connect ohmmeter between “VSS” terminal (2) and “GND” ter-
minal (3) of combination meter and turn cable joint (1) of
speedometer with a screwdriver. Ohmmeter indicator should
move back and forth between 0 (zero) and ∞ (infinity) 4 times
while cable joint is turned one full revolution.
Replace speedometer if check result is not satisfactory.
4) Install combination meter to instrument panel.
5) Connect negative cable at battery.
VEHICLE SPEED SENSOR (VSS) For A / T
INSPECTION
Vehicle speed sensor (1) itself can be checked on its resistance by
disconnecting connector.
NOTE:

Function of vehicle speed sensor can be checked by mea-
suring generated pulse as voltage.

For its measurement, use an analog type voltmeter while
spinning wheels on lift and with selector lever in D position.
Vehicle speed sensor specifications
Coil resistance100 – 300 Ω
Output voltage at 40 km / h (25 mile / h)approximately 1 V
FUEL LEVEL SENSOR (GAUGE)
Refer to Section 8.

6E2-14 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
IDLE SPEED / IDLE AIR CONTROL (IAC) DUTY
INSPECTION
Before idle speed / IAC duty check, make sure of the following.

Lead wires and hoses of Electronic Fuel Injection and engine
emission control systems are connected securely.

Accelerator cable has some play, that is, it is not tight.

Valve lash is checked and adjusted according to maintenance
schedule.

Ignition timing is within specification.

All accessories (wipers, heater, lights, A / C, etc.) are out of ser-
vice.

Air cleaner has been properly installed and is in good condition.

No abnormal air inhaling from air intake system.
After above items are all confirmed, check idle speed and IAC duty
as follows.
NOTE:
Before starting engine, place transmission gear shift lever in
“Neutral” (shift selector lever to “P” range for A / T vehicle),
and set parking brake and block drive wheels.
1) Connect SUZUKI scan tool (1) to DLC with ignition switch OFF,
if it is available.
2) Warm up engine to normal operating temperature.
3) Check engine idle speed and “IAC duty” as follow:
Select “Data List” mode on scan tool to check “IAC duty” and en-
gine speed.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
If duty and/or idle speed is out of specifications, inspect idle air
control system referring to Diagnostic Flow Table B-4 IDLE AIR
CONTROL SYSTEM CHECK in Section 6.
ENGINE IDLE SPEED AND IAC DUTY
A/C OFFA/C ON
M / T vehicle750±50 r / min (rpm)875±50 r/minA / T vehicle
at P/N range750 ±50 r/min (rpm)
8 – 25 or *8 – 35%
875 ±50 r/min
(rpm)
NOTE:
Duty values with (*) are applicable to vehicle used at high
altitude (higher than 2,000 m or 6,560 ft).
4) Check that 875 ± 50 r / min. idle speed is obtained with lighting
switch ON and heater blower switch in 2 – 4 position.
If not, check “Electric load (+)” circuit and “Heater blower switch
signal” circuit referring to “ELECTRONIC CONTROL SYSTEM”
in this section and idle air control system.
5) Check that specified engine idle speed is obtained with A / C ON
if vehicle is equipped with A / C.
If not, check A / C ON signal circuit.

1. Final gear
2. Differential gear assembly
3. Counter shaft
4. 1st and reverse brake
5. Counter driven gear11. Forward clutch
12. Direct clutch
13. Input shaft
14. Torque converter
15. Oil pump 6. Output shaft
7. Rear planetary gear
8. Front planetary gear
9. Valve body assembly
10. Oil strainer
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-3
GENERAL DESCRIPTION
The automatic transmission consists of the hydraulic torque converter, electronically controlled 3-speed automatic
transmission, countershaft and differential.
The transmission consists of 2 planetary gears, 2 disk clutches, 1 band brake, 1 disk brake and 1 one-way clutch.
Its operation is controlled by selecting a position from 6 positions (P, R, N, D, 2 and L ranges) manually by means
of the selector lever installed on the compartment floor.
In the D or 2 range, the gear ratio is changed for the 1st, 2nd or 3rd speed (D range only) automatically by engine
control module (electronic control).
For the automatic transmission fluid, DEXRON
-

E, DEXRON-


or its equivalent must be used. Lubrication
in the automatic transmission is provided by the oil pump which is operated by the engine revolution. Therefore,
the engine should not be stopped even during coasting to obtain proper lubrication.
When it becomes necessary to be towed, front wheels must be raised so as not to roll them.