2000 SUZUKI SWIFT Coolant

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-31
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates current flow time rate within
a certain set cycle of IAC valve (valve opening rate)
which controls the amount of bypass air (idle speed).
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

6-1-34 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
CONNECTOR “C01”
TERMINAL
NO.CIRCUITNORMAL
VOLTAGECONDITION
1Ground——
2Ground——
3Ground——
4EVAP canister purge valve10 – 14 VIgnition switch ON
Indication
deflection
5Power steering switch
deflection
repeated
0 V and
Ignition switch ON
0 V and
10 – 14 V
6Idle air control valve0 – 13 VAt specified idle speed after engine warmed
up
7Heater of HO2S-110 – 14 VIgnition switch ON
8Fuel injector NO.410 – 14 VIgnition switch ON
9Fuel injector NO.110 – 14 VIgnition switch ON
10Sensor ground——
11Camshaft position sensor0 – 0.8 V
and 4 – 6 VIgnition switch ON
12Blank——
13Heater oxygen sensor-1Refer to DTC P0130 diag. flow table
14Engine coolant temp. sensor0.55 – 0.95 VIgnition switch ON
Engine coolant temp.: 80C (176F)
15Intake air temp. sensor2.0 – 2.7 VIgnition switch ON
Intake air temp.: 20C (68F)
16Blank——
17Electric load signal (+)
0 – 1 VIgnition switch ON
Small light and rear defogger OFF
17Electric load signal (+)
10 – 14 VIgnition switch ON
Small light and rear defogger ON
18Blank——
19Ignition coil #2——
20Ignition coil #1——
21Fuel injector NO.210 – 14 VIgnition switch ON
22Power source for sensor4.75 – 5.25 VIgnition switch ON
23Crankshaft position sensor (+)——
24Crankshaft position sensor (–)——
25Blank——
26Manifold absolute pressure
sensor3.3 – 4.0 VIgnition switch ON
Barometric pressure: 100 kPa (760 mmHg)
27Blank——
28Immobilizer indicator lamp0 – 2 VIgnition switch ON28Immobilizer indicator lamp10 – 14 VWhen engine running
29Blank——
30Blank——
31Fuel injector NO.310 – 14 VIgnition switch ON

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-35
CONNECTOR “C02”
TERMINAL
NO.CIRCUITNORMAL
VOLTAGECONDITION
1A / C ON output signal0 VIgnition switch ON
2EGR valve (stepper motor10 – 14 VIgnition switch ON2coil 1)0 – 1 VEngine running at idle speed
3Data link connector10 – 14 VIgnition switch ON
4Heater of HO2S-210 – 14 VIgnition switch ON
5Power source10 – 14 VIgnition switch ON
6Power source10 – 14 VIgnition switch ON
7Power source for buck-up10 – 14 VIgnition switch ON and OFF
8EGR valve (stepper motor10 – 14 VIgnition switch ON8coil 3)10 – 14 VEngine running at idle speed
9EGR valve (stepper motor10 – 14 VIgnition switch ON9coil 2)10 – 14 VEngine running at idle speed
10Main relay10 – 14 VIgnition switch OFF10Main relay0.4 – 1.5 VIgnition switch ON
112-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at 2-range
12N-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at N-range
13Heated oxygen sensor-2Refer to DTC P0130 diag. flow table
14D-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at D-range
15R-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at R-range
16A/C input signal
10 – 14 VIgnition switch ON
A / C switch OFF
16A/C in ut signal
0 – 2 VIgnition switch ON
A / C switch ON
17EGR valve (stepper motor10 – 14 VIgnition switch ON17coil 4)0 – 1 VEngine running at idle speed
18Radiator fan control relay
10 – 14 V
Ignition switch ON
Engine coolant temp.: Below 92.5C
(199F)
18Radiator fan control relay
0 – 1 V
Ignition switch ON
Engine coolant temp.: Below 97.5C
(208F) or higher
19Fuelpumprelay0 – 1 VFor 2 seconds after ignition switch ON19Fuel um relay10 – 14 VAfter the above time
20Blank——
21P-range signal (A / T)
Indication
deflection
repeated
0 V and
10 – 14 V
Ignition switch ON
22Fuel level sensor (gauge)
0 – 2 VIgnition switch ON
Fuel tank fully filled
22Fuel level sensor (gauge)
4.5 – 7.5 VIgnition switch ON
Fuel tank emptied
23L-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at L-range
24Blank——

6-1-48 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
To combination
(ECT) meterTo other sensors
NOTE:
Before inspecting, be sure to check that cool-
ant temp. meter in combination meter indi-
cates normal operating temperature (Engine
is not overheating).
DTC P0115 ENGINE COOLANT TEMPERATURE (ECT) CIRCUIT
MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Low engine coolant temperature (High voltage-High resistance)

High engine coolant temperature (Low voltage-Low resistance)
“Lg / R” circuit open or shorted to power

“G” circuit open

ECT sensor malfunction

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Clear DTC, start engine and keep it at idle for 1 min.
2) Select “DTC” mode on scan tool and check DTC.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-49
Fig. 1 for Step 2 Fig. 2 for Step 5 Fig. 3 for Step 6
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check ECT Sensor and Its Circuit.
1) Connect scan tool with ignition switch OFF.
2) Turn ignition switch ON.
3) Check engine coolant temp. displayed on scan
tool. See Fig. 1.
Is –40C (–40F) or 119C (246F) indicated?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection”
in Section 0 A.
3Check Wire Harness.
1) Disconnect ECT sensor connector.
2) Check engine coolant temp. displayed on scan
tool.
Is –40C (–40F) indicated?Replace ECT sensor.“Lg / R” wire shorted to
ground.
If wire is OK, substitute
a known-good ECM
(PCM) and recheck.
4Does scan tool indicate –40C (–40F) at Step 2.Go to Step 6.Go to Step 5.
5Check Wire Harness.
1) Disconnect ECT sensor connector with
ignition switch OFF.
2) Check for proper connection to ECT sensor at
“G” and “Lg / R” wire terminals.
3) If OK, then with ignition switch ON, is voltage
applied to “G” wire terminal about 4 – 6 V?
See Fig. 2.Go to Step 4.“Lg / R” wire open or
shorted to power, or
poor C01-14
connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.
6Check Wire Harness.
1) Using service wire, connect ECT sensor
connector terminals. See Fig. 3.
2) Turn ignition switch ON and check engine
coolant temp. displayed on scan tool.
Is 119C (246F) indicated?Replace ECT sensor.“G” wire open or poor
C01-10 connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.

6-1-52 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Throttle
position
sensorTo other sensors
To other sensors
DTC P0121 THROTTLE POSITION CIRCUIT RANGE / PERFORMANCE
PROBLEM
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

After engine warmed up.

While vehicle running at specified engine speed.

No change in intake manifold pressure (constant throttle opening)

Difference between actual throttle opening (detected from TP sensor)
and opening calculated by ECM (PCM) (Obtained on the basis of
engine speed and intake manifold pressure) in larger than specified
value.
2 driving cycle detection logic, continuous monitoring
TP sensor malfunction

High resistance in the circuit

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF. Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Indication of fuel level meter in combination meter: 1 / 4 or more
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: between –10C and 80C (14F and 176F)
–Engine coolant temp.: 70C, 158F or higher
2) Warm up engine to normal operating temperature.
3) Increase vehicle speed to 30 – 40 mph, 50 – 60 km / h in 3rd gear or “D” range and hold throttle valve at that
opening position for 1 min.
4) Stop vehicle.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.

6-1-68 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Fig. 1 for Step 3 Fig. 2 for Step 4 Fig. 3 for Step 5
Fig. 4 for Step 5 Fig. 5 for Step 5 Fig. 6 for Step 6
1. Fuel delivery pipe
2. Fuel feed hose
3. Fuel pressure gauge &
3 way joint
STEPACTIONYESNO
8Check engine coolant temp. sensor for performance
(See Section 6E2).
Is it in good condition?Go to Step 9.Replace engine
coolant temp. sensor.
9Check intake air temp. sensor for performance
(See Section 6E2).
Is it in good condition?Go to Step 10.Replace intake air
temp. sensor.
10Check throttle position sensor for performance (See
Step 3 of DTC P0121 Diag. Flow Table).
Is it in good condition?Go to Step 11.Replace throttle
position sensor.
11Check PCV valve for valve clogging
(See Section 6E2).
Is it good condition?Substitute a known-
good ECM (PCM) and
recheck.Replace PCV valve.

Below
specified value
6-1-70 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
1. CKP sensor signal
2. No.1 fuel injector signal
3. No.3 fuel injector signal
4. Fuel injection time
Display of fuel injection signal using oscilloscope
Waveforms at specified idle speed5ms/Div
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Engine under other than high revolution condition

Not on rough road

Engine speed changing rate

Manifold absolute
pressure changing rate

Throttle opening changing rate

Misfire rate per 200 or 1000 engine revolutions (how
much and how often crankshaft revolution speed
changes) is higher than specified value
Engine overheating

Vacuum leaks (air inhaling) from air intake system

Ignition system malfunction (spark plug(s), high-
tension cord(s), ignition coil assembly)

Fuel pressure out of specification

Fuel injector malfunction (clogged or leakage)

Engine compression out of specification

Valve lash (clearance) out of specification

Manifold absolute pressure sensor malfunction

Engine coolant temp. sensor malfunction

PCV valve malfunction

EVAP control system malfunction

EGR system malfunction
DTC CONFIRMATION PROCEDURE
NOTE:
Among different types of random misfire, if misfire occurs at cylinders 1 and 4 or cylinders 3 and 2 simulta-
neously, it may not possible to reconfirm DTC by using the following DTC confirmation procedure. When
diagnosing the trouble of DTC P0300 (Random misfire detected) of the engine which is apparently misfir-
ing, even if DTC P0300 cannot be reconfirmed by using the following DTC confirmation procedure, pro-
ceed to the following Diag. Flow Table.
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: between –10C and 80C (14F and 176F)
–Engine coolant temp.: –10C, 14F or higher
4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-
sis” and “Freeze frame data check”.
Reference