2000 SUZUKI SWIFT manual transmission

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-19
Fig. 1 for Step 5. Fig. 2 for Step 5. Fig. 3 for Step 5.
When not using SUZUKI
scan tool:
lever position
Terminal
Selector
AUTOMATIC TRANSMISSION BASIC CHECK
This check is very important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been found in visual inspection. Follow the flow table carefully.
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAG. FLOW TABLE”
performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAG. FLOW
TABLE”.
2Check A / T Fluid.
Warm transmission to normal operating temperature and check
fluid level and contamination referring to “FLUID LEVEL
CHECK” of “ON-VEHICLE SERVICE” in this section.
Is it in good condition?Go to Step 3.Add or change
fluid.
3Check Fluid Pressure Control Cable.
1) Warm up engine to normal operating temperature.
2) Check fluid pressure control cable for play referring to
“FLUID PRESSURE CONTROL CABLE” of “ON-VEHICLE
SERVICE” in this section.
Is it in good condition?Go to Step 4.Adjust.
4Check Select Cable for Adjustment referring to “SELECT
CABLE” of “ON-VEHICLE SERVICE” in this section.
Is it adjusted correctly?Go to Step 5.Adjust.
5Check Transmission Range Sensor (Switch) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C03-3 C03-4 C03-5 C03-14
Go to Step 6.Go to Step 3 of
DTC P0705
Flow Table.
2) Check voltage at terminals C03-3, C03-4, C03-5, C03-14,
C03-15 and C03-16 for G10 engine model (C02-11, C02-12,
C02-14, C02-15, C02-21 and C02-23 for G13 engine
model) respectively with selector lever shifted to each
range. See Fig. 2.
Taking terminal C03-3 for G10 engine model (C02-11 for
G13 engine model) as an example, is battery voltage
indicated only when selector lever is shifted to “2” range and
0 V for other ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?
6Check Engine Idle speed referring to Section 6E1 or 6E2.
Is it in good condition?Go to
“SYMPTOM-TO-
INSPECTION
TABLE” below.Go to Section
6E1 or 6E2.
C03-5
(C02-21)C03-16
(C02-15)C03-4
(C02-12)C03-15
(C02-14)C03-3
(C02-11)C03-14
(C02-23)
PB + V0 V0 V0 V0 V0 V
R0 VB + V0 V0 V0 V0 V
N0 V0 VB + V0 V0 V0 V
D0 V0 V0 VB + V0 V0 V
20 V0 V0 V0 VB + V0 V
L0 V0 V0 V0 V0 VB + V

7B-22 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
Fig. 1 for Step 2. Fig. 2 for Step 2.
Fig. 3 for Step 2.
When not using SUZUKI
scan tool:
lever position
Terminal
Selector
TROUBLESHOOTING
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC FLOW
TABLE” performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAGNOSTIC
FLOW TABLE”.
2Check Transmission Range Sensor Circuit for Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C03-3, C03-4, C03-5, C03-14,
C03-15 and C03-16 for G10 engine model (C02-11, C02-12,
C02-14, C02-15, C02-21 and C02-23 for G13 engine model)
respectively with selector lever shifted to each range. See Fig. 2.
Taking terminal C03-3 for G10 engine model (C02-11 for G13
engine model) as an example, is battery voltage indicated only
when selector lever is shifted to “2” range and 0 V for other
ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?Intermittent
trouble. Check
for intermittent
referring to
“INTERMITTENT
AND POOR
CONNECTION”
in Section 0A.Go to Step 3.
3Check Select Cable for Adjustment referring to “SELECT
CABLE” of “ON-VEHICLE SERVICE” in this section.
Is it adjusted correctly?Go to Step 4.Adjust.
4Check Transmission Range Sensor.
1) Remove TR sensor from A / T.
2) At each of P, R, N, D, 2 and L shift position, check continuity
between terminals as well as each terminal and sensor
case. See Fig. 4.
Continuity should be indicated only between those
terminals as shown in Fig. 4 and 5 at each shift position.
Continuity should not exist between any terminal and
sensor case.
Are check results satisfactory?Go to Step 5.Replace TR
sensor.
5Check Transmission Range Sensor for Installation Position.
1) Install TR sensor to transmission referring to
“TRANSMISSION RANGE SENSOR” of “ON-VEHICLE
SERVICE” in this section.
2) Perform check as described in step 2 of this table.
Is check result satisfactory?Transmission
range sensor
maladjusted.Check “Y”, “Or / B”,
“R”, “Or / Y”,
“Gr / R”, “Gr” or
“Gr / Bl” (G10
engine model)
(“Br / Y”, “W/B”,
“R/W”, “W/R”,
“Y/R”, “Y/B” or
“R/B” (G13 engine
model)) circuit for
open or short.
If wires and
connections are
OK, substitute a
known-good PCM
and recheck.
C03-5
(C02-21)C03-16
(C02-15)C03-4
(C02-12)C03-15
(C02-14)C03-3
(C02-11)C03-14
C02-23)
PB + V0 V0 V0 V0 V0 V
R0 VB + V0 V0 V0 V0 V
N0 V0 VB + V0 V0 V0 V
D0 V0 V0 VB + V0 V0 V
20 V0 V0 V0 VB + V0 V
L0 V0 V0 V0 V0 VB + V

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-29
TROUBLESHOOTING
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC FLOW
TABLE” performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAGNOSTIC
FLOW TABLE”.
2Is DTC other than shift malfunction (DTC P0751 / P0756)
displayed?Go to applicable
DTC Flow Table.Go to Step 3.
3Perform Road Test to check if upshift and downshift take
place at specified vehicle speed, referring to “ROAD TEST”
in this section.
Do they take place properly?Intermittent
trouble. Check
electrical circuit
of system for
intermittent
referring to
“INTERMITTENT
AND POOR
CONNECTION”
in Section 0A.Go to Step 4.
4Perform Manual Shift Road Test referring to “MANUAL ROAD
TEST” in this section.
Is test result satisfactory?Go to Step 5.Go to “A/T
Basic Check”.
5Check Transmission Range Sensor and Its Circuit according
to Step 1 of DTC P0705 Flow Table.
Are they in good condition?Go to Step 6.“D” range
signal circuit
shorted to other
signal circuit or
TR sensor
malfunction.
6Check Output Shaft Speed Sensor and Its Circuit referring to
“OUTPUT SHAFT SPEED SENSOR CHECK” in this section.
Are they in good condition?Go to Step 7.Output shaft
speed sensor
circuit open or
short or output
shaft speed
sensor
malfunction.
7Check Shift Solenoid A and B for Operation referring to
“SHIFT SOLENOID VALVE CHECK” in this section.
Are they in good condition?Substitute a
known-good
PCM and
recheck.Replace shift
solenoid A or B.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-31
TABLE A-2 GEAR CHANGE FAILURE
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC
FLOW TABLE” performed?Go to Step 2.Go to “AUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLE”.
2Disconnect solenoid valve wire coupler and perform
manual road test.
Is upshift from 1st to 2nd possible?Go to Step 3.1-2 shift valve sticks
or Shift solenoid-B
(2nd brake solenoid)
valve sticks.
3Is upshift from 2nd to 3rd possible?Gear shift control
system defective.
Go to A / T Diagnostic
Flow Table B.2-3 shift valve sticks
or Shift solenoid-A
(Direct clutch
solenoid) valve
sticks.
TABLE A-3 EXCESSIVE SHOCK AT RANGE SELECTION OR GEAR CHANGE
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC
FLOW TABLE” performed?Go to Step 2.Go to “AUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLE”.
2Is line pressure proper?Go to Step 3.Regulator valve
defective, Throttle
valve defective or
Accelerator cable
maladjusted.
3Does excessive shock occur when selecting “D” range
from “N” range?Forward clutch
accumulator
operation failure,
Forward clutch worn
or Forward clutch oil
circuit check ball
operation failure. Go to Step 4.
4Does excessive shock occur when selecting “R” range
from “N” range?1st-Reverse brake
worn, 1st-Reverse
brake oil circuit check
ball operation failure.Go to Step 5.
5Does excessive shock occur at 1st to 2nd gear
change?2nd brake
accumulator
defective, 2nd brake
worn, 2nd brake oil
circuit check ball
operation failure.In case of excessive
shock at 2nd to 3rd
gear change, Direct
clutch worn or Direct
clutch oil circuit check
ball operation failure.

1. Solenoid valve wire coupler (Disconnected)
2. Transmission
7B-36 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
MANUAL ROAD TEST
This test checks the gears being used in L, 2 or D range when driven
with unoperated gear shift control system.
Test drive vehicle on a level road.
1) With selector lever in P range, start engine and warm it up.
2) After warming up engine, disconnect coupler of solenoid valve
wire as shown in left figure.
3) With selector lever in L range, start vehicle and accelerate to
30 km / h (19 mile / h). Check in this state that 1st gear is being
used.
4) At 30 km / h (19 mile / h), shift selector lever to 2 range and accel-
erate to 60 km / h (37 mile / h).
Check in this state that 2nd gear is being used.
5) At 60 km / h (37 mile / h), shift selector lever to D range and check
that 3rd gear is used when speed is higher than 60 km / h
(37 mile / h).
6) After above checks, stop vehicle then engine, and connect sole-
noid valve wire coupler.
ENGINE BRAKE TEST
WARNING:
Before test, make sure that there is no vehicle behind so as
to prevent rear-end collision.
1) While driving vehicle in 3rd gear of D range, shift selector lever
down to 2 range and check if engine brake operates.
2) In the same way as in step 1), check engine brake for operation
when selector lever is shifted down to L range.
3) If engine brake fails to operate in above tests, possible cause for
such failure are as follows.
Check each part which is suspected to be the cause.
Condition
Possible causes
Fails to operate when
shifted down to 2 rangeSecond brake defective
Fails to operate when
shifted down to L range1st-reverse brake defective

7B-42 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
TIGHTENING TORQUE SPECIFICATIONS
Refer to the same section of the service manual mentioned in the “FOREWORD” of this manual.
SPECIAL TOOLS
Refer to the same section of the service manual mentioned in the “FOREWORD” of this manual.