2000 SUZUKI SWIFT Change

Ignition coil
Igniter
Ignition switch
Main
fuse
Injector resistor
Fuel injector
Crankshaft
position sensor
Camshaft
position sensor
Ground
at engine “I / G COIL METER”
Main relay
6-68 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0300 RANDOM MISFIRE DETECTED (Misfire detected at 2 or more
cylinders)
DTC P0301 CYLINDER 1 MISFIRE DETECTED
DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0303 CYLINDER 3 MISFIRE DETECTED
CIRCUIT DESCRIPTION
ECM (PCM) monitors crankshaft revolution speed and engine speed via the crankshaft position sensor and cylin-
der No. via the camshaft position sensor. Then it calculates the change in the crankshaft revolution speed and from
how many times such change occurred in every 200 or 1000 engine revolutions, it detects occurrence of misfire.
When ECM (PCM) detects a misfire (misfire rate per 200 revolutions) which can cause overheat and damage to
the three way catalytic converter, it makes the malfunction indicator lamp (MIL) flash as long as misfire occurs at
that rate.
After that, however, when the misfire rate drops, MIL remains ON until it has been judged as normal 3 times under
the same driving conditions.
Also, when ECM (PCM) detects a misfire (misfire rate per 1000 revolutions) which will not cause damage to three
way catalytic converter but can cause exhaust emission to be deteriorated, it makes MIL light according to the 2
driving cycle detection logic.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-69
Below
specified value DTC DETECTING CONDITION
POSSIBLE CAUSE

Engine under other than high revolution condition

Not on rough road

Engine speed changing rate

Manifold absolute
pressure changing rate

Throttle opening changing rate

Misfire rate per 200 or 1000 engine revolutions (how
much and how often crankshaft revolution speed
changes) is higher than specified value
Engine overheating

Vacuum leaks (air inhaling) from air intake system

Ignition system malfunction (spark plug(s), high-
tension cord(s), ignition coil assembly)

Fuel pressure out of specification

Fuel injector malfunction (clogged or leakage)

Engine compression out of specification

Valve lash (clearance) out of specification

Manifold absolute pressure sensor malfunction

Engine coolant temp. sensor malfunction

PCV valve malfunction

EVAP control system malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Ambient temp.: –10C, 14F or higher
–Intake air temp.: 70C, 158F or lower
–Engine coolant temp.: –10 – 11 0C, 14 – 230F
4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-
sis” and “Freeze frame data check”.

Main
fuseMain relay
Idle speed
control relay
To TP sensor
Idle speed control actuator
6-86 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0505 IDLE CONTROL SYSTEM MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE
DTC will set when A, B or C condition is met.
A: Throttle opening change is small as compared with
electrically live time.
B: Throttle valve opening is not within its target range
with CTP switch ON.
C: Drive voltage exists though ECM (PCM) is not
outputting ISC drive command.
Malajusted accelerater cable

Poor movement of throttle valve

Closed throttle position switch malfunction

Idle speed control actuator malfunction

Idle speed control relay malfunction

“Gr / B”, “Gr / Y”, “Gr”, “Gr / R”, “Gr / G”, “Lg” or “B/Bl”
circuit open or short

Throttle position sensor malfunction

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Start cold engine.
4) Run it idle for 5 min.
5) Select “DTC” mode on scan tool and check DTC.
NOTE:
If engine speed changes up and down when engine speed is increased by opening throttle valve more
than half but not changing its opening, it is possible that closed throttle position switch is malfunction-
ing.

6-1-16 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
DTC
NO.DETECTING ITEMDETECTING CONDITION
(DTC will set when detecting:)MIL
P0335Crankshaft position sensor
circuit malfunctionNo signal for 2 sec. During engine cranking1 driving
cycle
P0340Camshaft position sensor circuit
malfunctionNo signal during engine running1 driving
cycle
P0400Exhaust gas recirculation
flow malfunction detectedExcessive or insufficient EGR flow2 driving
cycles
P0420Catalyst system efficiency below
threshold
Output waveforms of HO2S-1 and HO2S-2 are
similar.
(Time from output voltage change of HO2S-1 to that
of HO2S-2 is shorter than specification.)
2 driving
cycles
P0443Purge control valve circuit
malfunctionPurge control valve circuit is open or shorted to
ground2 driving
cycles
P0480Radiator fan control circuit
malfunctionRadiator cooling fan relay terminal voltage is low
when cooling temp. is lower than specification2 driving
cycles
P0500Vehicle speed sensor
malfunctionNo signal while running in “D” range or during fuel cut
at decelerating2 driving
cycles
P0505Idle control system malfunctionNo closed signal to IAC valve is detected2 driving
cycles
P0601Internal control module memory
check sum errorData write error (or check sum error) when written
into ECM (PCM)1 driving
cycle
P1450Barometric pressure sensor
circuit malfunctionBarometric pressure is lower or higher than
specification. (or sensor malfunction)1 driving
cycle
P1451Barometric pressure sensor
performance problem
Difference between manifold absolute pressure
(MAP sensor value) and barometric pressure
(barometric pressure sensor value) is larger than
specification during cranking.
2 driving
cycles
P1500Starter signal circuit malfunctionStarter signal is not inputted from engine cranking till
its start and after or it is always inputted2 driving
cycles
P1510ECM (PCM) backup power
source malfunctionNo backup power after starting engine1 driving
cycle

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-23
ConditionPossible Cause]Referring Item
Low oil pressure
Improper oil viscosity

Malfunctioning oil pressure switch

Clogged oil strainer

Functional deterioration of oil pump

Worn oil pump relief valve

Excessive clearance in various sliding partsEngine oil and oil filter change in
Section 0B
Oil pressure switch inspection in
Section 8
Oil pan and oil pump strainer
cleaning in Section 6A1
Oil pump in Section 6A1
Oil pump in Section 6A1
Engine noise
Note: Before
checking mechanical
noise, make sure
that:

Specified spark
plug in used.

Specified fuel is
used.Valve noise

Improper valve lash

Worn valve stem and guide

Weak or broken valve spring

Warped or bent valve
Piston, ring and cylinder noise

Worn piston, ring and cylinder bore
Connecting rod noise

Worn rod bearing

Worn crank pin

Loose connecting rod nuts

Low oil pressure
Crankshaft noise

Low oil pressure

Worn bearing

Worn crankshaft journal

Loose bearing cap bolts

Excessive crankshaft thrust play
Valve lash in Section 6A1
Valves inspection in Section 6A1
Valve springs inspection in
Section 6A1
Valves inspection in Section 6A1
Pistons and cylinders inspection
in Section 6A1
Crank pin and connecting rod
bearing inspection in Section 6A1
Crank pin and connecting rod
bearing inspection in Section 6A1
Connecting rod installation in
Section 6A1
Previously outlined
Previously outlined
Crankshaft and bearing
inspection in Section 6A1
Crankshaft and bearing
inspection in Section 6A1
Crankshaft inspection in
Section 6A1
Crankshaft thrust play inspection
in Section 6A1

6-1-24 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ConditionPossible CauseReferring Item
Overheating
Inoperative thermostat

Poor water pump performance

Clogged or leaky radiator

Improper engine oil grade

Clogged oil filter or oil strainer

Poor oil pump performance

Faulty radiator fan control system

Dragging brakes

Slipping clutch

Blown cylinder head gasketThermostat in Section 6B
Water pump in Section 6B
Radiator in Section 6B
Engine oil and oil filter change in
Section 0B
Oil pressure check in Section 6A1
Oil pressure check in Section 6A1
Radiator fan control system in
Section 6E2
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Cylinder head in Section 6A1
Poor gasoline
mileageIgnition system out of order

Leaks or loose connection of high-tension cord

Faulty spark plug (improper gap, heavy deposits
and burned electrodes, etc.)
Engine and emission control system out of
order

Malfunctioning EGR valve

High idle speed

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty EGR valve

Faulty fuel injector(s)

Faulty ECM (PCM)
Low compression
Others

Poor valve seating

Dragging brakes

Slipping clutch

Thermostat out of order

Improper tire pressure
High-tension cords in Section 6F1
Spark plugs in Section 6F1
EGR system in Section 6E2
Refer to item “Improper engine
idle speed” previously outlined
TP sensor, ECT sensor or MAP
sensor in Section 6E2
EGR system in Section 6E2
Diagnostic Flow Table B-1
Previously outlined
Valves inspection in Section 6A1
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Thermostat in Section 6B
Refer to Section 3F
Excessive engine
oil consumptionOil leakage

Blown cylinder head gasket

Leaky camshaft oil seals
Oil entering combustion chamber

Sticky piston ring

Worn piston and cylinder

Worn piston ring groove and ring

Improper location of piston ring gap

Worn or damaged valve stem seal

Worn valve stem
Cylinder head in Section 6A1
Camshaft in Section 6A1
Piston cleaning in Section 6A1
Pistons and cylinders inspection
in Section 6A1
Pistons inspection in Section 6A1
Pistons assembly in Section 6A1
Valves removal and installation in
Section 6A1
Valves inspection in Section 6A1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-25
ConditionPossible CauseReferring Item
Engine hesitates
(Momentary lack of
response as
accelerator is
depressed.
Can occur at all
vehicle speeds.
Usually most severe
when first trying to
make vehicle move,
as from a stop sign.)Ignition system out of order

Spark plug faulty or plug gap out of adjustment

Leaky high-tension cord
Fuel system out of order

Fuel pressure out of specification
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
Engine overheating
Low compression
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-3
EGR system in section 6E2
TP sensor, ECT sensor or MAP
sensor in Section 6E2
Diagnostic Flow Table B-1
Refer to “Overheating” section
Previously outlined
Surge
(Engine power
variation under
steady throttle or
cruise.
Feels like vehicle
speeds up and down
with no change in
accelerator pedal.)Ignition system out of order

Leaky or loosely connected high-tension cord

Faulty spark plug (excess carbon deposits,
improper gap, and burned electrodes, etc.)
Fuel system out of order

Variable fuel pressure
–Kinky or damaged fuel hose and lines
–Faulty fuel pump (clogged fuel filter)
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
High-tension cords in Section 6F1
Spark plugs in Section 6F1
Diagnostic Flow Table B-3
EGR system in Section 6E2
MAP sensor in Section 6E2
Diagnostic Flow Table B-1
Excessive
detonation
(Engine makes
continuously
sharp metallic
knocks that change
with throttle opening.
Sounds like pop corn
popping.)Engine overheating
Ignition system out of order

Faulty spark plug

Loose connection of high-tension cord
Fuel system out of order

Clogged fuel filter (faulty fuel pump) or fuel lines

Air inhaling from intake manifold or throttle body
gasket
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of ECT sensor or MAP sensor

Faulty fuel injector(s).

Faulty ECM (PCM)

Excessive combustion chamber depositsRefer to “Overheating” section
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-1 or B-2
EGR system in Section 6E2
ECT sensor or MAP sensor in
Section 6E2
Diagnostic Flow Table B-1
Piston and cylinder head cleaning
in Section 6A1

6-1-52 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Throttle
position
sensorTo other sensors
To other sensors
DTC P0121 THROTTLE POSITION CIRCUIT RANGE / PERFORMANCE
PROBLEM
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

After engine warmed up.

While vehicle running at specified engine speed.

No change in intake manifold pressure (constant throttle opening)

Difference between actual throttle opening (detected from TP sensor)
and opening calculated by ECM (PCM) (Obtained on the basis of
engine speed and intake manifold pressure) in larger than specified
value.
2 driving cycle detection logic, continuous monitoring
TP sensor malfunction

High resistance in the circuit

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF. Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Indication of fuel level meter in combination meter: 1 / 4 or more
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: between –10C and 80C (14F and 176F)
–Engine coolant temp.: 70C, 158F or higher
2) Warm up engine to normal operating temperature.
3) Increase vehicle speed to 30 – 40 mph, 50 – 60 km / h in 3rd gear or “D” range and hold throttle valve at that
opening position for 1 min.
4) Stop vehicle.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.