2000 SUZUKI SWIFT radiator

6-30 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
SCAN TOOL DATACONDITIONNORMAL CONDITION /
REFERENCE VALUES
DESIRED IDLEAt idling with no load after warming up, M / T850 r / min(DESIRED IDLE SPEED)
gg,
at neutral, A / T at “P” range850 r / min
TP SENSOR VOLT
(THROTTLE POSITIONIgnition switch
ON / engine
Throttle valve fully closedMore than 0.2 V(
SENSOR OUTPUT
VOLTAGE)ON / engine
stoppedThrottle valve fully openLess than 4.8 V
INJ PULSE WIDTH
(FUEL INJECTIONAt specified idle speed with no load after
warming up0.8 – 2.3 msec.(
PULSE WIDTH)At 2500 r / min with no load after warming up0.8 – 2.3 msec.
IAC FLOW DUTY (IDLE
AIR CONTROL FLOW
DUTY)
At idling with no load after warming up20 – 40%
TOTAL FUEL TRIMAt specified idle speed after warming up–35 – +35%
BATTERY VOLTAGEIgnition switch ON / engine stop10 – 14 V
CANIST PRG DUTY
(EVAP CANISTER
PURGE FLOW DUTY)
At specified idle speed after warming up0 – 100%
CLOSED THROT POS
(CLOSED THROTTLEThrottle valve at idle positionON(CLOSED THROTTLE
POSITION)Throttle valve opens larger than idle positionOFF
FUEL CUTWhen engine is at fuel cut conditionONFUEL CUTOther than fuel cut conditionOFF
RAD FAN
(RADIATOR FANIgnition switch
ON
Engine coolant temp.:
Lower than 92.5C
(199F)
OFF
(
CONTROL RELAY)ONEngine coolant temp.:
97.5C (208F) or higherON
ELECTRIC LOAD
Ignition switch ON / Headlight, small light,
heater fan and rear window defogger all
turned OFF
OFF
ELECTRIC LOADIgnition switch ON / Headlight, small light,
heater fan or rear window defogger turned
ON
ON
A / C SWITCH
Engine running after warming up, A / C not
operatingOFF
A/C SWITCHEngine running after warming up, A / C
operatingON
PSP SWITCH
Engine running at idle speed and steering wheel
at straight-ahead position.OFF
(if equipped).Engine running at idle speed and steering wheel
turned to the right or left as far as it stops.ON

FUEL TANK LEVEL––––––––––––0 – 100%
BAROMETRIC PRESS––––––––––––Display the barometric pressure
FUEL PUMP
Within 3 seconds after ignition switch ON or
engine runningON
Engine stop at ignition switch ON.OFF

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-33
CANIST PURGE DUTY (EVAP CANISTER
PURGE FLOW DUTY, %)
This parameter indicates valve ON (valve open) time
rate within a certain set cycle of EVAP purge solenoid
valve which controls the amount of EVAP purge.
0% means that the purge valve is completely closed
while 100% is a fully open valve.
CLOSED THROTTLE POSITION (ON / OFF)
This parameter will read ON when throttle valve is ful-
ly closed, or OFF when the throttle is not fully closed.
FUEL CUT (ON / OFF)
ON : Fuel being cut (output signal to injector is
stopped)
OFF : Fuel not being cut
RAD FAN
(RADIATOR FAN CONTROL RELAY, ON / OFF)
ON : Command for radiator fan control relay opera-
tion being output.
OFF : Command for relay operation not being out-
put.
ELECTRIC LOAD (ON / OFF)
ON : Headlight, small light, heater fan or rear win-
dow defogger ON signal inputted.
OFF : Above electric loads all turned OFF.
A / C SWITCH (ON / OFF)
ON : Command for A / C operation being output
from ECM (PCM) to A / C amplifier.
OFF : Command for A / C operation not being output.
FUEL TANK LEVEL (%)
This parameter indicates approximate fuel level in the
fuel tank. As the detectable range of the fuel level sen-
sor is set as 0 to 100%, however, with some models
whose fuel tank capacity is smaller, the indicated fuel
level may be only 70% even when the fuel tank is full.
PSP SWITCH (ON / OFF)
ON : PSP switch detects P / S operation (high PS
pressure).
OFF : PSP switch not detects P / S operation.
BAROMETRIC PRESS (kPa, inHg)
This parameter represents a measurement of baro-
metric air pressure and is used for altitude correction
of the fuel injection quantity and ISC actuator control.
FUEL PUMP (ON / OFF)
ON is displayed when the ECM (or PCM) activates the
fuel pump via the fuel pump relay switch.
VSS (A / T) (km / h, MPH)
If is computed by using pulse signals from vehicle
(output) speed sensor on automatic transmission.
TRANS RANGE (TRANSMISSION RANGE
SENSOR, P, R, N, D, 2 OR L)
It is indicated transmission range detected by trans-
mission range sensor.
SHIFT SOL 1-CON (SHIFT SOLENOID-1,
ON / OFF)
ON : ON command being output to shift solenoid-1
OFF : ON command not being output.
SHIFT SOL 2-CON (SHIFT SOLENOID-2,
ON / OFF)
ON : ON command being output to shift solenoid-2
OFF : ON command not being output.
SHIFT SOL 1-MON (SHIFT SOLENOID-1,
ON / OFF)
The monitor result of the shift solenoid-1 circuit is dis-
played.
ON : Electricity being passed to shift solenoid-1 or
circuit open.
OFF : Electricity not being passed or circuit short.
SHIFT SOL 2-MON (SHIFT SOLENOID-2,
ON / OFF)
The monitor result of the shift solenoid-2 circuit is dis-
played.
ON : Electricity being passed to shift solenoid-2 or
circuit open.
OFF : Electricity not being passed or circuit short.
THROT POS LEVEL (THROTTLE POSITION
LEVEL FOR A / T, “0”, “1”, “2”, “3”, “4”, “5”, “6”
or “7”)
This parameter indicates which level (zone) the
throttle valve opening is in. The throttle opening is di-
vided into 8 levels (zones) from “0” (about idle posi-
tion) to “7” (about full open) and signals are assigned
to each opening level (zone). ECM (PCM) control the
automatic gear change of the automatic transmission
by using these signals according to the signal from
the TP sensor.
GEAR POSITION
This parameter indicates the A / T gear position which
is computed on signals from the Transmission Range
Switch, VSS, TP Sensor, and so forth.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-35
CONNECTOR “C02”
TER-
MINALWIRE
COLORCIRCUITSTANDARD
VOLTAGECONDITION
1BECM (PCM) ground––
2W/BlPower source10 – 14 VIgnition switch ON
3—Blank——
4—Blank——
5—Blank——
6—Blank——
7R/GEVAP canister purge valve10 – 14 VIgnition switch ON
8G/OrShift solenoid B (A / T)
0 VIgnition switch ON, selector lever at “P”
range
8G/OrShift solenoid-B (A / T)
10 – 14 VIgnition switch ON, selector lever at “D”
range
9G/WShift solenoid A (A / T)
0 VIgnition switch ON, selector lever at “P”
range
9G/WShift solenoid-A (A / T)
10 – 14 VIgnition switch ON, selector lever at “D”
range
10OrIgniter (IGT)——
11Gr / YISC actuator——
12Y/BFuel injector10 – 14 VIgnition switch ON
13B/BlGround for injector——
14WPower source for back-up10 – 14 VIgnition switch ON and OFF
15W/BlPower source10 – 14 VIgnition switch ON
16Gr / BISC actuator relay0.3 – 1.0 VIgnition switch ON
17V/YMalfunction indicator lamp0.2 – 2.0 VIgnition switch ON17V/YMalfunction indicator lamp10 – 14 VWhen engine running
18V/GImmobilizer indicator lamp0.2 – 2.0 VIgnition switch ON18V/GImmobilizer indicator lamp10 – 14 VWhen engine running at idle
19Lg / BHeater of H02S-210 – 14 VIgnition switch ON
20BlRadiator fan control relay
10 – 14 VIgnition switch ON, Engine coolant
temp: Below 91.5C (197F)
20BlRadiator fan control relay
0.3 – 1.0 VIgnition switch ON, Engine coolant
temp: 96.0C (205F) or higher
21P/WFuelpumprelay0.3 – 1.3 VFor 2 seconds after ignition switch ON21P/WFuel pump relay10 – 14 VAfter the above time
22Bl / BMain relay0.4 – 1.5 VIgnition switch ON
23–Blank——
24Gr / RISC actuator——
25Y/REFE heater relay10 – 14 VIgnition switch ON
26B/RGround for injector——

6-38 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
1 2
1. ECM (PCM)
coupler disconnected
2. Ohmmeter
RESISTANCE CHECK
1) Disconnect ECM (PCM) couplers from ECM (PCM) with ignition
switch OFF.
CAUTION:
Never touch terminals of ECM (PCM) itself or connect
voltmeter or ohmmeter.
2) Check resistance between each terminal of couplers discon-
nected.
CAUTION:

Be sure to connect ohmmeter probe from wire harness
side of coupler.

Be sure to turn OFF ignition switch for this check.

Resistance in table below represents that when parts
temperature is 20C (68F).
TERMINALSCIRCUITSTANDARD RESISTANCE
C01-8 to C03-20H02S-1 heater11.7 – 14.3 Ω
C02-19 to C03-20H02S-2 heater11.7 – 14.3 Ω
C02-12 to C02-2 / 15Fuel injector2.4 – 3.6 Ω
C02-7 to C02-2 / 15EVAP canister purge valve30 – 34 Ω
C02-21 to C03-20Fuel pump relay100 – 120 Ω
C02-16 to C02-2 / 15ISC actuator relay100 – 120 Ω
C02-25 to C02-2 / 15EFE heater relay100 – 120 Ω
C02-8 to Body groundShift solenoid-B8 – 20 Ω
C02-9 to Body groundShift solenoid-A8 – 20 Ω
C02-20 to C02-2 / 15Radiator fan control relay100 – 120 Ω
C02-22 to C02-14Main relay100 – 120 Ω
C02-1 to Body groundGroundContinuity
C02-13 to Body groundGroundContinuity
C02-26 to Body groundGroundContinuity

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-39
INFORMATION SENSORS
-1. MAP sensor
-2. TP sensor
-3. IAT sensor
-4. ECT sensor
-5. Heated oxygen sensor-1
-6. VSS
-7. Ignition coil
-8. Battery
-9. CMP sensor (in Distributor)
-10. A/C contoller (if equipped)
-11. CKP sensor
-12. CTP switch (in ISC actuator)
-13. Heated oxygen sensor-2OTHERS
A: ECM (PCM)
B: Main relay
C: EVAP canister
D: Injector resistor
E: EFE heater
F: Electric load diode CONTROL DEVICES
a: Fuel injector
b: EVAP canister purge valve
c: Fuel pump relay
d: Malfunction indicator lamp
e: ISC actuator
f: Radiator fan control relay
g: Igniter
h: EFE heater relay
i: ISC actuator relay
COMPONENT LOCATION

6-80 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Fig. 1 for Step 1
Main
fuseIgnition switch“IG COIL METER”
Radiator fan
relay
Radiator fan motor
DTC P0480 RADIATOR FAN CONTROL SYSTEM MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Low voltage at terminal C02-20 when engine coolant
temp. is below 91C, 195F.
2 driving cycle detection logic, continuous monitoring.
“B/W” or “BI” circuit open or short

Radiator fan relay malfunction

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Warm up engine until radiator cooling fan starts to operate.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-81
Fig. 1 for Step 2 Fig. 2 for Step 3
1. Radiator fan relay
2. Relay box
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check Radiator Cooling Fan Relay and Its Circuit.
1) Turn ignition switch ON.
2) Check for voltage at terminal C02-20 of ECM
(PCM) connector connected, under following
condition. See Fig. 1.
When engine coolant temp. is lower than
96C, 205F and A / C switch turns OFF:
10 – 14 V
Is voltage as specified?Intermittent trouble or
faulty ECM (PCM).
Check for intermittent
referring to “Intermittent
and Poor Connection”
in Section 0A.Go to Step 3.
3Check Radiator Fan Control Relay.
1) Turn ignition switch OFF and remove radiator
fan relay.
2) Check for proper connection to the relay at
“B/W” and “Bl” wire terminals.
3) If OK, then measure resistance between
terminals a and b. See Fig. 2.
Is it 100 – 120 Ω?“B/W” or “Bl” circuit
open or short.
If wires and connections
are OK, substitute a
known-good ECM (PCM)
and recheck.Replace radiator fan
relay.

6-1-2 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
DTC P0300 Random Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0301 Cylinder 1 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0302 Cylinder 2 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0303 Cylinder 3 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0304 Cylinder 4 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0335 CKP Sensor Circuit
Malfunction 6-1- 73. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0340 CMP Sensor Circuit
Malfunction 6-1- 75. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0400 EGR Flow Malfunction 6-1- 78. . . .
DTC P0420 Catalyst System
Efficiency Below Threshold 6-1- 81. . . . . . . . . .
DTC P0443 Purge Control Valve Circuit
Malfunction 6-1- 84. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0480 Radiator Fan Control
System Malfunction 6-1- 85. . . . . . . . . . . . . . . . .
DTC P0500 Vehicle Speed Sensor
Malfunction 6-1- 87. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0505 Idle Control System
Malfunction 6-1- 91. . . . . . . . . . . . . . . . . . . . . . . . DTC P0601 Internal Control Module
Memory Check Sum Error 6-1- 93. . . . . . . . . . .
DTC P1450 Barometric Pressure
Sensor Low / High Input 6-1- 94. . . . . . . . . . . . .
DTC P1451 Barometric Pressure Sensor
Performance Problem 6-1- 94. . . . . . . . . . . . . . .
DTC P1500 Engine Starter Signal
Circuit Malfunction 6-1- 96. . . . . . . . . . . . . . . . . .
DTC P1510 ECM (PCM) Back-up
Power Supply Malfunction 6-1- 97. . . . . . . . . . .
Table B-1 Fuel Injector Circuit Check 6-1- 98. . .
Table B-2 Fuel Pump and Its Circuit
Check 6-1- 99. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 Fuel Pressure Check 6-1-101. . . . . . . .
Table B-4 A / C Signal Circuits Check 6-1-103. . .
Table B-5 PSP Switch Signal Circuit
Check 6-1-104. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-6 Electric Load Signal Circuit
Check 6-1-105. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-7 Radiator Cooling Fan Control
System Check 6-1-106. . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6-1-108 . . . . . . . . . . . . . . . . . . . . .