2000 SUZUKI SWIFT display

Display of fuel injection signal using oscilloscope
1. CMP sensor signal
2. Fuel injector signal
3. Fuel injection time
2V/Div.
20V/Div.1
2
10ms/Div
Waveforms at specified idle speed 3 Sensor rotor
in distributorCamshaft
position sensor
6-74 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0340 CAMSHAFT POSITION (CMP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

No CMP sensor signal for 2 seconds at engine
cranking (CKP sensor signal is inputted).
CMP sensor circuit open or short.

Signal rotor teeth damaged.

CMP sensor malfunction, foreign material being
attached or improper installation.

ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-2 and C01-10 of ECM (PCM) connector connected to ECM (PCM)
and check CMP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC.
2) Start engine and keep it at idle for 1 min.
3) Select “DTC” mode on scan tool and check DTC.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-77
1) 2) 3) 4) 35 – 45 mph
(55 – 65 km / h)
30 – 40 mph
(50 – 60 km / h)
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and tester, on a level road.
1) Turn ignition switch OFF.
Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Ambient temp.: –10C, 14F or higher
–Intake air temp.: 70C, 158F or lower
–Engine coolant temp.: 70 – 11 0C, 158 – 230F
2) Start engine and drive vehicle at 40 – 47 mph, 65 – 75 km / h for 15 min. or longer.
While this driving, if “Catalyst Monitoring TEST COMPLETED” is displayed in “READINESS TESTS” mode and
DTC is not displayed in “DTC” mode, confirmation test is completed.
If “TEST NOT COMPLTD” is still being displayed, continue test driving.
3) Decrease vehicle speed at 28 – 34 mph, 45 – 55 km / h, and hold throttle valve at that opening position for 2 min.
and confirm that short term fuel trim vary within –20% –+20% range.
4) Stop vehicle (do not turn ignition switch OFF) and confirm test results according to following “Test Result Con-
firmation Flow Table”.
Test Result Confirmation Flow Table
STEPACTIONYESNO
1Check DTC in “DTC” mode and pending DTC in
“ON BOARD TEST” or “PENDING DTC” mode.
Is DTC or pending DTC displayed?Proceed to applicable
DTC Diag. Flow Table.Go to Step 2.
2Set scan tool to “READINESS TESTS” mode and
check if testing has been completed.
Is test completed?No DTC is detected
(confirmation test is
completed).Repeat DTC
confirmation
procedure.

6-82 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Vehicle speed
sensor in
combination meterC03-2
C03-2
DTC P0500 VEHICLE SPEED SENSOR (VSS) MALFUNCTION (M / T)
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

VSS signal not inputted while vehicle running in “D”
range or during fuel cut at deceleration.
2 driving cycle detection logic, continuous monitoring
“B/Bl” circuit open

“Y/G” circuit open or short

VSS malfunction

ECM malfunction

Speedometer cable malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Clear DTC and warm up engine to normal operating temperature.
2) Increase vehicle speed to 50 mph, 80 km / h in 3rd gear or “2” range while observing vehicle speed displayed
on scan tool.
3) Release accelerator pedal and with engine brake applied, keep vehicle coasting (fuel cut condition) for 4 sec.
or more.
4) Check pending DTC and DTC.

6-88 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Fig. 1 for Step 2 Fig. 2 for Step 3
Lever is apart
from plunger
Lever contacts
with plunger Condition “A”:
throttle lever is in contact
with ISC actuator plunger
Condition “B”:
Throttle lever is apart
from plunger
DTC P0510 CLOSED THROTTLE POSITION (CTP) SWITCH MALFUNCTION
CIRCUIT DESCRIPTION – Refer to DTC P0505 section.
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Even when vehicle is started from stop and
accelerated to specified vehicle speed, CTP switch
does not turn from ON to OFF (or from OFF to ON).
2 driving cycle detection logic, continuous
monitoring
“Lg”, “Gr / G” or “B/Bl” circuit open or short

CTP switch malfunction

ECM (PCM) malfunction
NOTE:
When DTC P0105, P0120 and / or P0510 are indicated together, it is possible that “Lg” circuit is open.
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF, clear DTC with ignition switch ON and start engine.
2) Increase vehicle speed to 20 mph, 32 km / h and then stop vehicle.
3) Repeat above step 2) 15 times.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check CTP Switch Operation.
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON.
Does CTP switch operate properly under following
conditions respectively?
Condition “A”: ON displayed on scan tool
Condition “B”: OFF displayed on scan tool
Is test result satisfactory?Intermittent trouble.
Check for intermittent
referring to
“Intermittent and
Poor Connection in
Section 0A.Go to Step 3.
3Check CTP switch.
1) Arrange 3 new 1.5 V batteries in series (4.5 V in
total).
2) Connect these batteries to CTP switch terminals
“4” and “5”.
3) Under following each condition, check voltage
between CTP switch terminals “6” and “5”.
Condition “A”: 0 – 1 V
Condition “B”: 3.5 – 5.5 V
Is measured voltage as specified?Check “Lg”, “Gr / G”
and “B/Bl” wires and
connections for open
or short.
If wires and
connections are OK,
substitute a known-
good ECM (PCM) and
recheck.Replace ISC motor
set (throttle lower
body with ISC
actuator).

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-13
MALFUNCTION INDICATOR LAMP (MIL)
CHECK
1) Turn ON ignition switch (but the engine at stop) and check that
MIL lights.
If MIL does not light up (or MIL dims), go to “Diagnostic Flow
Table A-1” for troubleshooting.
2) Start engine and check that MIL turns OFF.
If MIL remains ON and no DTC is stored in ECM (PCM), go to
“Diagnostic Flow Table A-2” for troubleshooting.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
1) Prepare SUZUKI scan tool (Tech-1).
2) With ignition switch OFF, connect it to data link connector (DLC)
(1) located on underside of instrument panel at driver’s seat side.
Special Tool:
(A): SUZUKI scan tool
(B): Mass storage cartridge
(C): 16 / 14 pin DLC cable
3) Turn ignition switch ON and confirm that MIL lights.
4) Read DTC, pending DTC and freeze frame data according to
instructions displayed on scan tool and print it or write it down.
Refer to scan tool operator’s manual for further details.
If communication between scan tool and ECM (PCM) is not pos-
sible, check if scan tool is communicable by connecting it to
ECM (PCM) in another vehicle. If communication is possible in
this case, scan tool is in good condition. Then check data link
connector and serial data line (circuit) in the vehicle with which
communication was not possible.
5) After completing the check, turn ignition switch off and discon-
nect scan tool from data link connector.

6-1-30 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
SCAN TOOL DATACONDITIONNORMAL CONDITION /
REFERENCE VALUES
DESIRED IDLE
(DESIRED IDLE SPEED)At idling with no load after warming up, M / T
at neutral, A / T at “P” range750 r / min
TP SENSOR VOLT
(THROTTLE POSITIONIgnition switch
ON / engine
Throttle valve fully closedMore than 0.2 V(
SENSOR OUTPUT
VOLTAGE)ON / engine
stoppedThrottle valve fully openLess than 4.8 V
INJ PULSE WIDTH
(FUEL INJECTION
At specified idle speed with no load after
warming up2.0 – 3.6 msec.(
PULSE WIDTH)At 2500 r / min with no load after warming up2.0 – 3.6 msec.
IAC FLOW DUTY (IDLE
AIR CONTROL FLOW
DUTY)
At idling with no load after warming up5 – 25%
TOTAL FUEL TRIMAt specified idle speed after warming up–35 – +35%
BATTERY VOLTAGEIgnition switch ON / engine stop10 – 14 V
CANIST PRG DUTY
(EVAP CANISTER
PURGE FLOW DUTY)
––––––––––––0 – 100%
CLOSED THROT POS
(CLOSED THROTTLEThrottle valve at idle positionON(CLOSED THROTTLE
POSITION)Throttle valve opens larger than idle positionOFF
FUEL CUTWhen engine is at fuel cut conditionONFUEL CUTOther than fuel cut conditionOFF
RADIATOR FAN
(RADIATOR FANIgnition switch
ON
Engine coolant temp.:
Lower than 92.5C
Lower than (199F)
OFF
(
CONTROL RELAY)ONEngine coolant temp.:
97.5C (208F) or higherON
ELECTRIC LOAD
Ignition switch ON / Headlight, small light,
heater fan and rear window defogger all
turned OFF
OFF
ELECTRIC LOADIgnition switch ON / Headlight, small light,
heater fan or rear window defogger turned
ON
ON
A / C SWITCH
Engine running after warming up, A / C not
operatingOFF
A/C SWITCHEngine running after warming up, A / C
operatingON
PNP SIGNAL (PARK /
NEUTRAL POSITIONIgnition switch
Selector lever in “P” or “N”
positionP / N Range
NEUTRAL POSITION
SIGNAL) A / T only
g
ONSelector lever in “R”, “D”, “2”
or “L” positionD Range
EGR VALVEAt specified idle speed after warming up0%
FUEL TANK LEVEL––––––––––––0 – 100%
BAROMETRIC PRESS––––––––––––Display the barometric pressure
FUEL PUMP
Within 3 seconds after ignition switch ON or
engine runningON
Engine stop at ignition switch ON.OFF
BRAKE SWIgnition switchBrake pedal is depressingONBRAKE SWg
ONBrake pedal is releasingOFF
BLOWER FANIgnition switchBlower fan switch ONONBLOWER FA Ng
ONBlower fan switch OFFOFF
A / C MAG CLUTCHIgnition switchA / C switch ONONA/C MAG CLUTCHg
ONA / C switch OFFOFF

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-31
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates current flow time rate within
a certain set cycle of IAC valve (valve opening rate)
which controls the amount of bypass air (idle speed).
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-47
Fig. 1 for Step 2 Fig. 2 for Step 3 Fig. 3 for Step 4
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check IAT Sensor and Its Circuit.
1) Connect scan tool to DLC with ignition switch
OFF.
2) Turn ignition switch ON.
3) Check intake air temp. displayed on scan tool.
See Fig. 1.
Is –40C (–40F) or 119C (246F) indicated?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection”
in Section 0A.
3Check Wire Harness.
1) Disconnect IAT sensor connector with ignition
switch OFF.
2) Check for proper connection to IAT sensor at
“Gr / R” and “G” wire terminals.
3) If OK, then with ignition switch ON, is voltage
applied to “Gr / R” wire terminal about 4 – 6 V?
See Fig. 2.Go to Step 5.“Gr / R” wire open or
shorted to power, or
poor C01-15
connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.
4Does scan tool indicate –40C (–40F) at Step 2.Go to Step 6.Go to Step 5.
5Check Wire Harness
1) Check intake air temp. displayed on scan tool
with ignition switch ON.
Is –40C (–40F) indicated?Replace IAT sensor.“Gr / R” wire shorted to
ground.
If wire is OK, substitute
a known-good ECM
(PCM) and recheck.
6Check Wire Harness.
1) Using service wire, connect IAT sensor
connector terminals.
2) Check intake air temp. displayed on scan tool
with ignition switch ON. See Fig. 3.
Is 119C (246F) indicated?Replace IAT sensor.“Gr / R” wire open or
poor C01-10
connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.