2000 SUZUKI SWIFT Output shaft speed sensor

12 W / R “N”-range signal (A / T)
13 R Heated oxygen sensor-2
14 Y / R “D”-range signal (A / T)
15 R / W “R”-range signal (A / T)
16 Lg / B A / C SW signal
17 R / W EGR valve (stepper motor coil 4)
18 P / G Radiator fan relay
19 Y / Bl Fuel pump relay
20 —— ———
21 W / B “P”-range signal (A / T)
22 P / Bl Fuel level gauge
23 R / B “L”-range signal (A / T)
24 —— ———
1 V Malfunction indicator lamp
Vehicle speed sensor (M / T)
Output shaft speed sensor (+)
(A / T)
3 —— ———
4 G / W Shift solenoid – A (A / T)
5 Gr Throttle position (TP) sensor
6 B / W Ignition switch signal
7 Y / B Data link connector
Output shaft speed sensor (–)
(A / T)
9 —— ———
10 G GND for HO2S-2
11 G / Or Shift solenoid – B (A / T)
12 —— ———
13 —— ———
14 —— ———
15 —— ———
16 Br Tachometer signal
17 B / Y Engine start signal
CON-
NECTORTERMINALWIRE
COLORCIRCUITCON-
NECTORTERMINALWIRE
COLORCIRCUIT
20
Br / Y 19
Br / W
C02 C01C02
C03
Wire color
B : Black
B / Or : Black / Orange
B / W : Black / White
B / Y : Black / Yellow
Bl : Blue
Bl / Or : Blue / Orange
Bl / B : Blue / Black
Bl / R : Blue / Red
Bl / Y : Blue / Yellow
Br : Brown
Br / W : Brown / White
Br / Y : Brown / Yellow
G : Green
G / Or : Green / Orange
G / R : Green / Red
G / W : Green / White
Gr : Gray
Gr / R : Gray / Red
Lg / B : Lightgreen / Black
Lg / R : Lightgreen / RedP : Pink
P / Bl : Pink / Blue
P / G : Pink / Green
V : Violet
V / G : Violet / Green
V / R : Violet / Red
V / W : Violet / White
W : White
W / B : White / Black
W / R : White / Red
R : Red
R / B : Red / Black
R / Bl : Red / Blue
R / G : Red / Green
R / W : Red / White
R / Y : Red / Yellow
Y / B : Yellow / Black
Y / Bl : Yellow / Blue
Y / R : Yellow / Red
2
P
8
Bl
6E2-12 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
1 B Ground for ECM / PCM
2 B / Or Ground for drive circuit
3 B / Or Ground for drive circuit
4 V / R Canister purge valve
5 G / W Power steering pressure switch
6 V / W IAC valve
7 Bl Heater of HO2S-1
8 Bl / Or No.4 fuel injector
9 Bl / R No.1 fuel injector
10 G Ground for sensor circuit
11 B / W CMP sensor
12 —— ———
13 R Heated oxygen sensor-1
14 Lg / R Coolant temp. sensor
15 Gr / R Intake air temp. sensor
16 —— ———
17 Br / Y Electric load (+)
18 —— ———
IG coil assembly for
No.2 and 3 spark plugs
IG coil assembly for
No.1 and 4 spark plugs
21 Bl / B No.2 fuel injector
22 P Power supply for sensor
23 W CKP sensor (+)
24 B CKP sensor (–)
25 —— ———
26 G MAP sensor
27 —— ———
28 V / G Immobilizer indicator lamp
29 —— ———
30 —— ———
31 Bl / Y No.3 fuel injector
1 G / R A / C compressor clutch
2 R / Y EGR valve (stepper motor coil 1)
3 R / G Data link connector
4 Lg / B Heater of HO2S-2
5 R / B Power source
6 R / B Power source
7 W Backup power source
8 R EGR valve (stepper motor coil 3)
9 R / Bl EGR valve (stepper motor coil 2)
10 Gr Ground for main relay
11 Y / B “2”-range signal (A / T)

7B-2 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
Table B-1 Gear Shift Failure in “D” or
“2” Range 7B-38. . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 Gear is Shifted to 2nd Gear in
“L” Range Vehicle Does Not Move
Backward in “R” Range 7B-38. . . . . . . . . . . . . .
Transmission range sensor check 7B-39. . . . Output shaft speed sensor check 7B-39. . . . .
Shift solenoid valve circuit check 7B-40. . . . . .
Throttle position sensor check 7B-41. . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7B-42 . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS7B-42 . . . . . . . . . . . . . . . . . . . . . .

[G10 Engine Model]
1. PCM
2. Camshaft position (CMP) sensor
3. Throttle position (TP) sensor
4. Engine coolant temperature (ECT) sensor
5. Transmission range sensor (shift switch)
6. Output shaft speed sensor (A / T VSS)7. Malfunction indicator lamp (MIL)
8. Data link connector (DLC)
9. Shift solenoid-A
(No.1, Direct clutch solenoid valve)
10. Shift solenoid-B
(No.2, 2nd brake solenoid valve)11. Ignition switch
12. Main relay
13. Inhibitor switch
14. To starter
15. Terminal arrangement of PCM coupler
(Viewed from harness side)
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-5
ELECTRONIC SHIFT CONTROL SYSTEM

7B-6 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
[G13 Engine Model]
1. PCM
2. Camshaft position (CMP) sensor
3. Throttle position (TP) sensor
4. Engine coolant temperature (ECT) sensor
5. Transmission range sensor (shift switch)
6. Output shaft speed sensor (A / T VSS)7. Malfunction indicator lamp (MIL)
8. Data link connector (DLC)
9. Shift solenoid-A
(No.1, Direct clutch solenoid valve)
10. Shift solenoid-B
(No.2, 2nd brake solenoid valve)11. Ignition switch
12. Main relay
13. Inhibitor switch
14. To starter
15. Terminal arrangement of PCM coupler
(Viewed from harness side)

1. PCM
2. Instrument panel
TP sensor
Transmission range sensor
Output shaft speed sensor
(A / T VSS)
Shift solenoid-B
(2nd brake solenoid valve)
Shift solenoid-A
(Direct clutch solenoid valve)PCM
1. Throttle position sensor
2. Throttle body
A: Ground
3. Ground terminal
4. Reference voltage
terminal
5. Output voltage terminal
6. TP sensor
C: Output voltage
(opening angle signal)
D: Power supply from ECM
(reference voltage)
[G10 engine model]
[G13 engine model]
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-7
POWERTRAIN CONTROL MODULE (PCM)
The powertrain control module controls the shift solenoid B (2nd
brake solenoid valve) and the shift solenoid A (direct clutch sole-
noid valve) by sending electric signals to them so as to attain auto-
matic gear shift between the 1st and 2nd gears, and the 2nd and
3rd gears. Equipped as PCM sensed parameters are the throttle
position sensor, transmission range switch and vehicle speed sen-
sor. These switch and sensors sense the throttle valve opening, se-
lector lever’s position and vehicle speed, and send those signals to
the powertrain control module. Then, the powertrain control module
opens and closes valves of the above solenoids according to these
signals. The powertrain control module is installed to the underside
of the instrument panel at the driver’s seat side.
GEAR SHIFT CONTROL SYSTEM
THROTTLE POSITION SENSOR (TP sensor)
The throttle position sensor consisting of a potentiometer is con-
nected to the throttle valve shaft.
Throttle valve opening signal (output voltage) is transmitted from
throttle position sensor to PCM as voltage signal. PCM uses it as
one of the signals to control transmission gear shift.

1. Countershaft gear
2. Output shaft speed sensor
A: Magnetic core end
D or 2
1→2
18
11
52
33D
2→3
33
21
97
613→2
14
9
82
51D or 2
2→1
14
9
37
23L
2→1
37
23
37
23 Full close
Full openkm / h
mile/h
km / h
mile/h Throttle SpeedGear Selector
VEHICLE SPEED
UpshiftDownshift
THROTTLE VALVE OPENING
[G10 Engine Model]
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-9
OUTPUT SHAFT SPEED SENSOR (A / T VSS)
The output shaft speed sensor consists of a magnetic core with
magnet and coil. It is mounted on transmission case with 0.6 mm
(0.024 in.) air gap between the core end and countershaft gear
tooth.
While the countershaft rotates, magnetic flux is cut by gear tooth
thus a pulse is generated in the sensor coil according to the speed.
And then, the pulse is transmitted to engine control module as
speed signal.
AUTOMATIC SHIFT DIAGRAM
Automatic shift schedule as a result of shift control is shown below. In case that selector lever is shifted to L range
at a higher than 37 km / h (23 mile / h) (G10 engine model), 40 km / h (25 mile / h) (G13 engine model) speed, 2nd
gear is operated and then down shifts to 1st at a speed lower than that. No up shift is available in L range.

Counter
shaft gear
*1: For G10 engine model
*2: For G13 engine model
1. PCM
2. Output shaft speed sensor
3. Terminal arrangement of PCM coupler
(Viewed from harness side)
7B-24 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
DTC P0720 OUTPUT SPEED SENSOR (A / T VSS) CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION – Refer to “GENERAL DESCRIPTION” in this section.
DTC DETECTING CONDITION
POSSIBLE CAUSE
No signal inputted while running vehicle with “D” or “2”
range.
“P” or “Bl” circuit open or short.

Output shaft speed sensor malfunction.

Foreign material being attached or sensor installed
improperly.

Gear damaged.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC, shift selector lever to “2” range and drive vehicle at 3500 r / min engine speed for 3.5 seconds.
3) Stop vehicle and check DTC.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-25
Fig. 1 for Step 2. Fig. 2 for Step 3. Fig. 3 for Step 3.
TROUBLESHOOTING
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC
FLOW TABLE” performed?Go to Step 2.Go to
”AUTOMATIC
TRANSMISSION
DIAGNOSTIC
FLOW TABLE”.
2Check Output Shaft Speed Sensor for Resistance.
1) Disconnect output shaft speed sensor connector with
ignition switch OFF.
2) Check for proper connection to output shaft speed
sensor at “P” and “Bl” wire terminals.
3) If OK, then check resistance of output shaft speed
sensor. See Fig. 1.
Resistance between terminals : 100 – 300 Ω
Resistance between terminal
and transmission : 1 MΩ or more
Are check results satisfactory?Go to Step 3.Replace output
shaft speed
sensor.
3Check visually output shaft speed sensor and counter
shaft gear for the following.
See Fig. 2 and 3.

No damage

No foreign material attached

Correct installation
Are they in good condition?“P” or “Bl” wire open or
shorted to ground or
poor C03-2 or C03-13
for G10 engine model
(C03-2 or C03-8 for
G13 engine model)
connection.
If wire and connection
are OK, intermittent
trouble or faulty PCM.
Check for intermittent
referring to
“INTERMITTENT
AND POOR
CONNECTION” in
Section 0A.Clean, repair or
replace.