2000 SUZUKI SWIFT Atc

1. Crank timing belt pulley bolt
Direction of crankshaft
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-13
3) Check that timing mark (3) on camshaft timing belt pulley (1) is
aligned with “V” mark (2) on cylinder head cover (4). If not, align
two marks by turning camshaft but be careful not to turn it more
than its allowable turning range which is described on previous
page.
4) Check that punch mark (2) on crank timing belt pulley (4) is
aligned with arrow mark (3) on oil pump case. If not, align two
marks by turning crankshaft but be careful not to turn it more
than its allowable turning range which is described on previous
page.
5) With two sets of marks aligned, install timing belt (1) on two pul-
leys in such a way that the drive side of belt is free of any slack,
and with tensioner plate pushed up by finger.
And then install tensioner spring and spring damper (2) as
shown in figure, and handtighten tensioner stud.
NOTE:

When installing timing belt, match arrow mark (
) on
timing belt with rotating direction of crankshaft.

In this state, No.1 piston is at top dead center of compres-
sion stroke.
6) To take up slack of timing belt, turn crankshaft two rotations
clockwise after installing it. After making sure that belt is free
from slack, tighten tensioner stud (1) first and then tensioner bolt
(2) to each specified torque.
Then confirm again that two sets of marks are aligned respec-
tively.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
(b): 27 N
.m (2.7 kg-m, 19.5 lb-ft)

ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-17
INSPECTION
Camshaft journal wear:

Check camshaft journals and camshaft housings for pitting,
scratches, wear or damage.
If any malcondition is found, replace camshaft or cylinder head
with housing. Never replace cylinder head without replacing
housings.
Check clearance by using gaging plastic (1). The procedure is as
follows.
1) Clean housings and camshaft journals.
2) Make sure that all valve lash adjusters are removed and install
camshaft to cylinder head.
3) Place a piece of gaging plastic the full width of journal of cam-
shaft (parallel to camshaft).
4) Install housings as outlined on the following page and evenly
torque housing bolts to specified torque. Housings MUST be
torqued to specification in order to assure proper reading of
camshaft journal clearance.
NOTE:
Do not rotate camshaft while gaging plastic is installed.
5) Remove housing, and using scale (2) on gaging plastic envel-
op, measure gaging plastic width at its widest point.
JournalStandardLimitJournal
clearance0.040 – 0.082 mm
(0.0016 – 0.0032 in.)0.12 mm
(0.0047 in.)
If measured camshaft journal clearance exceeds limit, mea-
sure journal (housing) bore and outside diameter of camshaft
journal. Replace camshaft or cylinder head assembly which-
ever the difference from specification is greater.
Item
Standard
Camshaft journalNo.126.000 – 26.021 mm
(1.0236 – 1.0244 in.)
j
bore dia.No.2 &
No.330.000 – 30.021 mm
(1.1811 – 1.1819 in.)
Camshaft journalNo.125.939 – 25.960 mm
(1.0212 – 1.0220 in.)
j
O.D.No.2 &
No.329.939 – 29.960 mm
(1.1787 – 1.1795 in.)

4. Damper
6A1-22 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
2) Install tensioner (2) and tensioner plate (3):
Do not tighten tensioner bolt (1) with wrench yet. Hand tighten
only at this time.
Check to ensure that plate movement in arrow direction as
shown in figure causes tensioner to move in the same direction.
If no associated movement between plate and tensioner occurs,
remove tensioner and plate again and reinsert plate lug into ten-
sioner hole.
3) Check that timing mark (2) on camshaft timing belt pulley is
aligned with “V” mark (1) on cylinder head cover. If not, align two
marks by turning camshaft but be careful not to turn it more than
its allowable turning range which is described on previous page.
4) Check that timing mark (2) on crankshaft timing belt pulley is
aligned with arrow mark (1) on oil pump case. If not, align two
marks by turning crankshaft but be careful not to turn it more
than its allowable turning range which is described on previous
page.
5) Install timing belt and tensioner spring (2).
With two sets of marks aligned and tensioner plate pushed up,
install timing belt on two pulleys in such a way that drive side (1)
of belt is free from any slack.
And then install tensioner spring as shown in figure, and hand-
tighten tensioner stud (3).
NOTE:

When installing timing belt, match arrow mark (
) on
timing belt with rotating direction of crankshaft.

In this state, No. 4 piston is at top dead center of compres-
sion stroke.

6A1-36 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
Rocker Arm-to-Rocker Arm Shaft Clearance
Using a micrometer and a bore gauge, measure rocker shaft dia.
and rocker arm l.D.
Difference between two readings is arm-to-shaft clearance on
which a limit is specified.
If limit is exceeded, replace shaft or arm, or both.
Item
StandardLimit
Rocker arm l.D.15.996 – 16.014 mm
(0.629 – 0.630 in.)———
Rocker arm shaft dia.15.969 – 15.984 mm
(0.6287 – 0.6293 in.)———
Arm-to-shaft clearance0.012 – 0.045 mm
(0.0005 – 0.0018 in.)0.09 mm
(0.0035 in.)
Cam Wear
Using a micrometer, measured height of cam. If measured height
is below limit, replace camshaft.
Cam height
StandardLimit
Intake cam36.184 – 36.344 mm
(1.4246 – 1.4309 in.)36.084 mm
(1.4206 in.)
Exhaust cam35.900 – 36.060 mm
(1.4134 – 1.4197 in.)35.800 mm
(1.4094 in.)
Camshaft Runout
Hold camshaft between two “V” blocks, and measure runout by us-
ing a dial gauge.
If runout exceeds the limit, replace camshaft.
Runout limit: 0.10 mm (0.0039 in.)
Camshaft Journal Wear
Check camshaft journals and camshaft housings for pitting,
scratches, wear or damage.
If any malcondition is found, replace camshaft or cylinder head with
housing. Never replace cylinder head without replacing housing.

“a”: 50 mm (1.96 in.)
“b”: 95 mm (3.74 in.)
“a”: 23 mm (0.91 in.)
6A1-56 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
INSPECTION
Cylinders

Inspect cylinder walls for scratches, roughness, or ridges which
indicate excessive wear. If cylinder bore is very rough or deeply
scratched, or ridged, rebore cylinder and use oversize piston.

Using a cylinder gauge, measure cylinder bore in thrust and axial
directions at two positions as shown in figure.
If any of the following conditions is noted, rebore cylinder.
1) Cylinder bore dia. exceeds limit.
2) Difference of measurements at two positions exceeds taper lim-
it.
3) Difference between thrust and axial measurements exceeds
out-of-round limit.
Cylinder bore dia. limit: 74.15 mm (2.9196 in.)
Tapper and out-of-round limit: 0.10 mm (0.0039 in.)
NOTE:
If any one of four cylinders has to be rebored, rebore all four
to the same next oversize. This is necessary for the sake of
uniformity and balance.
Pistons

Inspect piston for faults, cracks or other damaged.
Damaged or faulty piston should be replaced.

Piston diameter:
As indicated in figure, piston diameter should be measured at a
position 23 mm (0.91 in.) from piston skirt end in the direction per-
pendicular to piston pin.
Standard73.970 – 73.990 mm
(2.9122 – 2.9130 in.)
Piston
diameterOversize:
0.25 mm
(0.0098 in.)74.220 – 74.230 mm
(2.9220 – 2.9224 in.)
0.50 mm
(0.0196 in.)74.470 –74.480 mm
(2.9319 – 2.9323 in.)

1 or 2
Piston
No.1 Cylinder
No.2 Cylinder
No.3 Cylinder
No.4 Cylinder
Crank
pulley
side
Flywheel
side
6A1-60 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
5) Remove cap and using a scale (2) on gaging plastic (1) enve-
lope, measure gaging plastic width at the widest point (clear-
ance).
If clearance exceeds its limit, use a new standard size bearing
and remeasure clearance.
Item
StandardLimit
Bearing
clearance0.020 – 0.050 mm
(0.0008 – 0.0019 in.)0.080 mm
(0.0031 in.)
6) If clearance can not be brought to within its limit even by using
a new standard size bearing, regrind crankpin to undersize
and use 0.25 mm undersize bearing.
ASSEMBLY
NOTE:
Two sizes of piston are available as standard size spare part
so as to ensure proper piston-to-cylinder clearance. When
installing a standard size piston, make sure to match piston
with cylinder as follows.
a) Each piston has stamped number 1 or 2 as shown. It represents
outer diameter of piston.
b) There are also stamped numbers of 1 and 2 on the cylinder block
as shown. The first number represents inner diameter of No.1
cylinder, the second number of No.2 cylinder, the third number
of No.3 cylinder and the fourth number of No.4 cylinder.

1. Gaging plastic
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-71
Main Bearings
General information

Service main bearings are available in standard size and 0.25
mm (0.0098 in.) undersize, and each of them has 5 kinds of bear-
ings differing in tolerance.

Upper half of bearing (2) has oil groove (3) as shown in figure.
Install this half with oil groove to cylinder block (1).

On each main bearing cap, arrow mark and number are em-
bossed as shown in figure.
When installing each bearing cap to cylinder block, point arrow
mark toward crankshaft pulley side and install each cap from that
side to flywheel side in ascending order of numbers “1”, “2”, “3”,
“4” and “5”. Tighten cap bolts to specified torque.
Inspection
Check bearings for pitting, scratches, wear or damage.
If any malcondition is found, replace both upper and lower halves.
Never replace one half without replacing the other half.
Main bearing clearance
Check clearance by using gaging plastic (1) according to the follow-
ing procedure.
1) Remove bearing caps.
2) Clean bearings and main journals.
3) Place a piece of gaging plastic to full width of bearing (parallel
to crankshaft) on journal, avoiding oil hole.
4) Install bearing cap as previously outlined and evenly toque cap
bolts to specified torque.
Bearing cap MUST be torqued to specification in order to assure
proper reading of clearance.
Tightening Torque
(a): 54 N
.m (5.4 kg-m, 39.0 lb-ft)
NOTE:
Do not rotate crankshaft while gaging plastic is installed.

7B-32 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
STALL TEST
This test is to check overall performance of automatic transmission
and engine by measuring stall speed at D and R ranges.
Be sure to perform this test only when transmission fluid is at normal
operating temperature (70–80C / 158–176F) and its level is be-
tween FULL HOT and LOW HOT. (Refer to “Fluid level” in this sec-
tion.)
CAUTION:
Do not run engine at stall more than 5 seconds continuous-
ly, for oil temperature may rise excessively high.
1) Install tachometer.
2) Apply parking brake and block vehicle wheels.
3) Start engine with selector lever shifted to P range.
4) Depress brake pedal.
5) Shift selector lever to D range and depress accelerator pedal ful-
ly while watching tachometer. Read engine rpm quickly when it
has become constant (stall speed).
6) Release accelerator pedal immediately after stall speed is
checked.
7) In the same way, check stall speed at R range.
8) Stall speed should be within following specification.
Stall speed: 2,500 – 2,900 r / min
(For both G10 and G13 engine models)
9) Possible causes for out-of-specification stall speed are as fol-
lows. Check each part which is suspected to be the cause.
Stall speed measured
Possible causes
Lower than specification
Engine output insufficient

Torque converter defective
Higher than specification in
D range
Forward clutch slippage

One-way clutch defective
Higher than specification in
R range
Direct clutch slippage

1st-reverse brake slippage