TYPE 1 TYPE 2
BODY ELECTRICAL SYSTEM 8-3
KEYLESS ENTRY SYSTEM (IF EQUIPPED)
The keyless entry system uses radio wave. When the button on the transmitter is pressed, a signal is transmitted
in the form of radio wave to the receiver. Then the signal causes the door lock controller to lock and unlock the door.
The door locks can not operated with the transmitter when either of the following conditions applies.
For 2 seconds after the ignition switch is turned from ON to OFF position.
The ignition switch is at ON or START position.
Any door is open.
DIAGNOSIS
KEYLESS ENTRY SYSTEM (IF EQUIPPED)
ConditionPossible CauseCorrection
The power door lock function
is available but the keyless
entry function is not.Fuse blown
Code registration error
Transmitter battery dead
Wiring or grounding faulty
Receiver faulty
Transmitter faultyReplace fuse to check for short.
Register code.
Replace battery.
Repair as necessary.
Replace.
Replace.
Only one power door lock
does not operate.Wiring or coupler faulty
Actuator (door lock motor) faultyRepair as necessary
Replace.
Operation distance unstable.Transmitter battery dead
Transmitter faultyReplace battery.
Replace.
NOTE:
The operation distance of this system varies depending on the position where the transmitter is oper-
ated, at the front side, the rear side or the lateral side. The distance can be affected by radio noises from
a TV station, a power plant, a broadcasting station and so forth.
ON-VEHICLE SERVICE
ENGINE COOLANT TEMP. (ECT) METER AND
SENSOR
ECT SENSOR
INSPECTION
1) Warm up ECT sensor (1) observing resistance between sensor
terminal (2) and sensor unit (1). Resistance should be de-
creased with increase of its temperature.
2) Check resistance between sensor terminal (2) and sensor unit
(1). If check result is not as specified below, replace sensor.
Temperature
Resistance
50C (122F)136 – 216 Ω
8G
IMMOBILIZER CONTROL SYSTEM 8G-1
GENERAL DESCRIPTION8G- 2 . . . . . . . . . . . . . .
On-Board Diagnostic System
(Self-Diagnosis Function) 8G- 4. . . . . . . . . . . . .
DIAGNOSIS8G- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions in Diagnosing
Troubles 8G- 6. . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSTIC FLOW TABLE 8G- 8. . . . . . . . . . . . .
Diagnostic Trouble Code Check
(Immobilizer Control Module) 8G-10. . . . . . . . .
Diagnostic Trouble Code Check (ECM) 8G-10. .
Diagnostic Trouble Code Table 8G-12. . . . . . . . .
A-1 Code (DTC) is not Outputted
from Diagnostic Output Terminal
of Immobilizer Diagnostic Coupler 8G-13. . . . . A-2 Immobilizer Indicator Lamp Check
(Immobilizer Indicator Lamp does not
Light at Ignition Switch ON) 8G-14. . . . . . . . . . .
A-3 Immobilizer Indicator Lamp Check
(Immobilizer Indicator Lamp Remains
ON after Engine Starts) 8G-15. . . . . . . . . . . . . .
HOW TO REGISTER IGNITION KEY8G-16 . . . . .
PROCEDURE AFTER IMMOBILIZER
CONTROL MODULE REPLACEMENT8G-17 . .
PROCEDURE AFTER ECM
REPLACEMENT8G-18 . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS8G-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 8G
IMMOBILIZER CONTROL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
Whether the immobilizer indicator lamp is used in the particular vehicle or not depends on specifica-
tions. If there is a monitor coupler in the engine room near the left strut assembly, the vehicle is not
equipped with immobilizer indicator lamp and if there isn’t, it is equipped with immobilizer indicator
lamp.
For the descriptions (items) not found in this section, refer to the section 8G of the Service Manual men-
tioned in FOREWORD of this manual.
CONTENTS
