2000 SUZUKI GRAND VITARA light
[x] Cancel search: lightPage 494 of 801
YH4
GRAND
VITARA
CLUTCH 7C1-13
1. Release fork
2. Clip
3. Input shaftªBº
ªBº
ªAº 3
2
1
1
2
4) Install clip to release fork and apply grease.
ªAº: Grease 99000-25010
Then install release fork and release bearing as shown in figure.
5) Slightly apply grease to input shaft and install clutch disc. Then
join transmission transfer assembly with engine. Refer to SEC-
TION 7A.
ªBº: Grease 99000-25210
NOTE:
Turn crankshaft with wrench from front while inserting
transmission input shaft to clutch disc until splines mesh.
Page 506 of 801
YH4
GRAND
VITARA
7E-4 DIFFERENTIAL (FRONT)
Components and Functions
ComponentFunction
4WD switch
When the transfer shift lever is shifted to 4L or 4H position, this switch turns ON
and causes the 4WD control system to turn ON, unless it is shifted to N or 2H
within 1 second.
ECM or PCM
When the 4WD switch turns ON [unless it turns OFF within 1 second], this com-
ponent actuates the pump assembly. If the pressure in the air pump assembly
fails to increase higher than the set level even after the pump motor has run more
than 10 seconds, this component stops the motor to protect it.
Air pump assembly
Pump motor
Release valve
Pressure switchThe air pump assembly consists of a pump motor, release valve and a pressure
switch.
Pump motor:
Produces positive pressure which actuates the actuator.
Release valve:
Closes when transfer shift lever is shifted to 4H or 4L so that the positive pressure
is applied to the actuator, and opens when N or 2H to release the pressure to the
atmosphere.
Pressure switch:
Turns ON and OFF depending on the pressure level in the pump assembly
(whether higher or lower than the set pressure level). ECM or PCM detects the
pressure level through this switch.
Differential case assembly
Free axle hub
Axle lock clutch
ActuatorThe free axle hub, axle lock clutch and actuator are installed in the differential
left case. The positive pressure produced in the air pump assembly is applied
to the actuator which then pushes the axle lock clutch to be engaged with the free
axle hub. In this state, the drive force is transmitted to the front axle, resulting in
the 4WD mode.
When the actuator is free from the positive pressure [when it is under the atmo-
spheric pressure], the axle lock clutch is pushed back by the return spring force
and cannot be engaged with the free axle hub, resulting in the 2WD mode.
ª4WDº indicator lampIt lights up when 4WD control system is in the 4WD mode.
Page 508 of 801
YH4
GRAND
VITARA
7E-6 DIFFERENTIAL (FRONT)
STEPACTIONYESNO
1Turn ON ignition switch (but engine at stop) and
check malfunction indicator lamp.
Does lamp light up?Go to step 2.A trouble has
occurred at some
place. Repair it
referring to
MALFUNCTION
INDICATOR LAMP
(ªCHECK ENGINEº
LAMP) CHECK in
DIAGNOSIS of
SECTION 6.
2Check 4WD switch circuit.
Turn ignition switch ON and check that voltage
between terminal C51-2-18 and terminal C51-3-17
(ground) for G16 / J20 (terminal C51-1-11 and terminal
C51-3-26 (ground) for H25) is as follows.
When transfer shift lever is in N or 2H: 10 ± 14 V
When transfer shift lever is in 4L or 4H: 0 ± 1 V
Is the check result satisfactory?Go to step 3.Check 4WD switch
(refer to SECTION
7A), ªB / Orº and ªBº
circuits of 4WD
switch.
If OK, substitute a
known-good ECM
(PCM) and recheck.
3Check power supply.
1) Turn ignition switch ON.
2) Check voltage between C51-2-7 and C51-3-17
(ground) for G16 / J20 (C51-1-15 and C51-3-26
(ground) for H25). The check results should be as
follows.
When transfer shift lever is in N or 2H: 0 ± 1 V
When transfer shift lever is in 4L or 4H: 10 ± 14 V
Is the check result satisfactory?Go to step 4.Check ªRº circuit. If
it is OK, substitute a
known-good ECM
(PCM) and recheck.
4Check air pump assembly circuit.
1) Check for proper connection to air pump
assembly at all terminals.
2) Turn ignition switch ON.
3) Check voltage between C51-2-27 and C51-3-17
(ground) for G16 / J20 (C51-1-18 and C51-3-26
(ground) for H25). The check result should be as
follows.
When transfer shift lever is in 2H or N: 0 ± 1 V
When transfer shift lever is in 4L or 4H
(more than 4 seconds after shifted to 4L or 4H):
10 ± 14 V
Is the check result satisfactory?Go to step 5.Check air pump
assembly referring
to ªON-VEHICLE
SERVICEº, and then
ªPº circuit.
If OK, substitute a
known-good ECM
(PCM) and recheck.
5Check 4WD indicator lamp circuit.
1) Turn ignition switch ON.
2) Check voltage between E61-19 and C51-3-17
(ground) for G16 / J20 (C51-1-7 and C51-3-26
(ground) for H25). The check result should be as
follows.
When transfer shift lever is in 2H or N: 10 ± 14 V
When transfer shift lever is in 4L or 4H: 0 ± 1 V
Is the check result satisfactory?4WD control system
is in good condition.Check ªOr / Bº circuit
(including indicator
lamp and
combination meter).
If OK, substitute a
known-good ECM
(PCM) and recheck.
Page 526 of 801
YH4
GRAND
VITARA
8
BODY ELECTRICAL SYSTEM 8-1
SECTION 8
BODY ELECTRICAL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
WIRING SYSTEM
(Harnesses, Connectors, Fuses, Relay, Switches, Grounds, System Circuit Diagram)Section 8A . . . . . . .
LIGHTING SYSTEMSection 8B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER INFORMATIONSection 8C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WINDOWS, MIRRORS, SECURITY AND LOCKSSection 8D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMMOBILIZER CONTROL SYSTEMSection 8F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 532 of 801
YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 533 of 801
YH4
GRAND
VITARA
6
5
1. Headlight assembly
2. Halogen bulb
3. Socket cover
4. Turn signal light bulb
5. Position light bulb
6. Turn signal light bulb socket
7. Position light bulb socket
8B-2 LIGHTING SYSTEM
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
HEADLIGHTS
Page 534 of 801
YH4
GRAND
VITARA
1. Headlight leveling switch
2. Headlight leveling unit (actuator)
3. Headlight
4. Headlight leveling unit shaft
Switch
PositionHeadlight beam
down angle
0 ÐÐÐ
1 0.624
2 1.243
3 1.867
4 2.479
LIGHTING SYSTEM 8B-3
HEADLIGHT WITH LEVELING SYSTEM (IF EQUIPPED)
Page 535 of 801
YH4
GRAND
VITARA
8B-4 LIGHTING SYSTEM
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
HEADLIGHTS
TroublePossible causeCorrection
Only one light does not
lightBulb blown
Headlight L or R fuse blown
Socket, wiring or grounding faultyReplace bulb
Replace fuse to check for short
Repair
Headlights do not lightHeadlight L and R fuses blown
Lighting and dimmer switch faulty
Defective light relay
Wiring or grounding faultyReplace fuses to check for short
Replace switches
Replace light relay
Repair
Only one beam (ªHiº or
ªLoº) does not lightBulb blown
Lighting or dimmer switch faultyReplace bulb
Replace switch
HEADLIGHTS WITH LEVELING SYSTEM (IF EQUIPPED)
TroublePossible causeCorrection
Both headlights do not
moveªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)
Leveling switch faulty
Supply voltage too lowReplace fuse to check for short
Replace switch
Recharge or replace battery
One of headlights (either
Right or Left) does not
moveSocket, wiring or grounding faulty
Actuator faulty
Vehicle body around headlight deformed
Headlight ass'y itself deformedRepair
Replace actuator
Repair body
Replace headlight ass'y
TURN SIGNAL AND HAZARD WARNING LIGHTS
TroublePossible causeCorrection
Flash rate high or one side
only flashesIncorrect bulb
One of light bulbs burnt out
Turn signal / hazard warning relay faulty
Open circuit or high resistance existing
Replace bulb
Replace
Replace relay
RepairOen circuit or high resistance existing
between turn signal / hazard warning
switch and lights on one side
Wiring or grounding faulty
Re air
Repair
No flashingªTURN / BACKº and / or ªHAZARDº fuse(s)
blown (Hard Top Model)
ªTRNº and / or ªHAZº fuse(s) blown
(Canvas Top Model)
Open circuit or high resistance existing
between battery and switch
Turn signal / hazard relay faulty
Combination switch or hazard switch faulty
Wiring or grounding faultyReplace fuse(s) to check for
short
Check bulb and check circuit
Replace relay
Replace switch
Repair
Flash rate lowSupply voltage too low
Turn signal / hazard relay faultyCheck charging system
Replace relay