2000 SUZUKI GRAND VITARA light

YH4
GRAND
VITARA
8G-30 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
09931-76030
16 / 14 pin DLC cable
09931-76011
Suzuki scan tool (Tech 1A kit)1. Storage case
2. Operator's manual
3. Tech 1A
4. DLC cable
(14 / 26 pin, 09931-76040)
5. Test lead/probe
6. Power source cable
7. DLC cable adapter
8. Self-test adapter
Immobilizer cartridge of
version 1.1 or more
NOTE:
Use this cable only with im-
mobilizer cartridge of ver-
sion 1.1 or more.
Use of this cable with 96
immobilizer cartridge will
disable 96 immobilizer car-
tridge from operating prop-
erly.
Mass storage cartridge of
version1.5 or more
PROCEDURE AFTER ECM / PCM
REPLACEMENT
When ECM / PCM was replaced, including when replaced because
rechecking by using a known-good ECM / PCM was necessary dur-
ing trouble diagnosis, register ECM/Immobilizer Control Module
code in ECM / PCM by performing following procedure.
1) Perform Steps 1) and 2) described in ªHow to register ignition
keyº section. And then turn ignition switch ON.
2) Using TECH1, register ECM/Immobilizer Control Module code in
ECM / PCM by executing ªRECORD ECU (RECORD ECM / PCM/
ICM)º command in SELECT MODE menu.
NOTE:
For operation procedure of Suzuki scan tool, refer to TECH1
operator's manual.
3) [Vehicle equipped with monitor coupler]
Make sure that malfunction indicator lamp lights when ignition
switch is turned OFF once and then ON.
[Vehicle not equipped with monitor coupler]
Make sure that immobilizer indicator lamp lights when ignition
switch is turned OFF once and then ON.
SPECIAL TOOLS

YH4
GRAND
VITARA
Hole to hole distance
ªa ± gº : 276 mm (10.87 in.)
ªa ± kº : 1000 mm (39.37 in.)
ªb ± b'º : 1302 mm (51.26 in.)
ªb ± gº : 730 mm (28.74 in.)
ªc ± c'º : 668 mm (26.30 in.)
ªc ± eº : 414 mm (16.30 in.)
ªc ± gº : 406 mm (15.98 in.)
ªc ± jº : 1029 mm (40.51 in.)
ªc ± kº : 1000 mm (39.37 in.)
ªd ± d'º : 1302 mm (51.26 in.)
ªd ± eº : 189 mm (7.44 in.)
ªd ± c'º : 1016 mm (40.00 in.)
ªd ± gº : 672 mm (26.46 in.)
ªd ± kº : 968 mm (38.11 in.)
ªe ± e'º : 1456 mm (57.32 in.)ªf ± f'º : 1550 mm (61.02 in.)
ªf ± hº : 299 mm (11.77 in.)
ªf ± jº : 811 mm (31.93 in.)
ªg ± kº : 854 mm (33.62 in.)
ªh ± h'º : 1339 mm (52.72 in.)
ªh ± j'º : 1504 mm (59.21 in.)
ªh ± jº : 677 mm (26.65 in.)
ªh ± kº : 927 mm (36.50 in.)
ªi ± i'º : 1344 mm (52.91 in.)
ªi ± jº : 391 mm (15.39 in.)
ªi ± kº : 760 mm (29.92 in.)
ªj ± j'º : 1348 mm (53.07 in.)
ªj ± kº : 676 mm (26.61 in.)
ªl ± jº : 961 mm (37.83 in.)
ªl ± kº : 1018 mm (40.08 in.)
a. Front bumper installation clip hole
b (b'). Front bumper installation hole
c (c'). Headlight installation hole
d (d'). Headlight installation resin nut hole
e (e'). Headlight installation hole
f (f'). Front fender installation hole
g. Center member installation hole
h (h'). Fender installation reference hole
i (i'). Fender installation hole
j (j'). Fender installation reference hole
k. Garnish installation clip hole
l. Mounting installation hole
9-26 BODY SERVICE
BODY DIMENSIONS
4 door model, 2 door model

YH4
GRAND
VITARA
When the welding or heating operation causes the
original galvanization or other anticorrosive materials
to be burnt, the interior and under-body panel sur-
faces must be cleaned.
Removal of residues of the burning should be carried
out carefully when the relevant place has boxtype
construction or has shape which limits the access to
the interior surfaces. In general, the following method
can be used satisfactorily for the removal of those res-
idues.Scrape the accessible places. If a standard putty knife
or scraper does not fit to the elevant place, consider
to use a more flexible scraper to a place narrowly en-
closed by sheet metals.
A jet of compressed air can remove most residues,
and is effective to limited areas.
However, this type of operation absolutely requires
eye protection.
BODY SERVICE 9-37
The metal service replacement parts (or assemblies)
are coated with electro-deposition primer.
For the proper adhesion of a paint, the following finish
process (refinish steps) becomes necessary.
1) Use wax or grease-removing solvent to clean the
part.
2) Use a wet or dry sand-paper (No. 400) to polish the
panel lightly. Do not polish it forcibly to produce any
scratch. Clean the part again.
3) If factory-applied primer coating is cut through to
the bare metal, apply metal conditioner to the bare
metal exposed to open air. As for method of use of
the metal conditioner, follow directions on the con-
tainer.
4) Apply primer-surfacer to the part completely dry
before starting sand-paper polishing. As for drying
time, follow directions advised on the primer-sur-
facer container.
5) Use a wet or dry sand-paper (No. 400) and water
to polish the panel lightly.
6) Wash the part again.
7) Apply color, coating to the part.
8) Different paints demand different drying methods.
Hence, follow directions advised on the pertinent
paint container.9) When lacquer coating (quick-drying paint coat-
ing) is applied, dry coated surface and polish it
with compound.
In the case of the melamine or acrylic coating,
compound polishing can be omitted after drying.
10) If the case of lacquer coating, wax should not be
applied to coated surface until the surface has
dried completely (for approx. two months).
Before replacing exterior parts or assemblies, check
paint conditions of all the covered or hidden interior
surfaces. If any rust scale is found at these places,
proceed as follows:
1) Use a proper wire brush, adhesive or liquid rust re-
moving agent to remove rust. As for the method of
use, follow directions advised for respecitve mate-
rials.
2) If necessary, wash parts with detergent, rinse, and
dry them.
3) Before installing exterior body parts, apply anticor-
rosive compound to all cleaner surfaces of exterior
body parts. Also, apply anticorrosive compound to
inner surfaces of exterior body parts to be
installed.
METAL REPLACEMENT PARTS FINISHING

YH4
GRAND
VITARA
1. Spot light
2. Head lining
3. Sunvisor assemblies
4. Room light
5. Trim
6. Assist grips
1. Sliding roof motor
2. Mounting screw
1. Motor assy
2. Hole (body)
3. Hole (cam)
9-66 BODY SERVICE
SLIDING ROOF MOTOR / RELAY
REMOVAL
1) Remove head lining, refer to HEAD LINING REMOVAL in this
section.
2) Disconnect coupler and remove sliding roof motor assembly by
removing 3 screws.
CAUTION:
After removing sliding motor assembly, do not move
guide and link.
INSTALLATION
For installation, reverse removal procedure, noting following point.
Before installing, connect coupler and push the CLOSE side of the
slide switch.

YH4
GRAND
VITARA
BODY SERVICE 9-73
5
46
4. Assistant grip
5. Rear room light
6. Inner trim
1. Roof harness
2. Rear washer hose
3. Adhesive tape
Front 1. Room light
2. Sunshade assembly
3. Spot light
IWATA
CAMI
HEAD LINING
REMOVAL
1) Remove spot light and sliding roof switch (if equipped).
2) Remove sunshade assembly.
3) Remove room light and spacer.
4) Remove assistant grips.
5) Remove inner trims covering head lining and door opening trim.
6) Remove rear speaker cover (if equipped).
7) Disconnect rear washer hose and roof harness from body.
8) Remove head lining.
NOTE:
Adhesive double coated tape is used to attach rear part of
head lining. Detach head lining from roof after removing all
above parts.
INSTALLATION
1) Set roof harness and washer hose to head lining with tape.
2) Clean roof where adhesive tape of head lining will be attached.
3) Peel off release liner of adhesive tape on head lining and install
it to body.
4) Install assistant grips a, b, c and d in that order.

YH4
GRAND
VITARA
9-74 BODY SERVICE
1. Door opening trim
2. Head liningSetSet
4. Assistant grip
5. Rear room light
6. Inner trim 1. Room light
2. Sunshade assembly
3. Spot light
IWATA
CAMI
5) Install door opening trim.
6) Install spot light, sunshade assembly, speaker cover, room light
and inner trims covering head lining.

YH4
GRAND
VITARA
BODY SERVICE 9-75
1. Canvas top
2. Rear topbow
3. Side body garnish
4. Luggage mat end garnish
5. Assistant grip
6. Sunshade assembly
7. Sunshade hook
8. Front topbow lock
9. Canvas top snap
10. Front seat belt
11. Front pillar trim
12. Rear side inner lower trim
13. Rear side inner upper trim
14. Room light connector
15. Room light harness clamp
16. Roof trim
17. Left-front seat belt
ROOF TRIM (2 DOOR MODEL)
REMOVAL
1) Remove canvas top.
2) Remove rear topbow.
3) Remove side body garnishes.
4) Remove luggage mat end garnish.
5) Remove assistant grips.
6) Remove sunshade assemblies.
7) Remove sunshade hooks.
8) Remove front topbow locks.
9) Remove canvas top snaps.
10) Remove front seat belts.
11) Remove front pillar trims.
12) Remove rear side inner lower trims.
13) Remove rear side inner upper trims.
14) Disconnect room light connector and remove room light har-
ness clamp.
15) Remove roof trim.
CAUTION:
Be very careful not to separate roof trim consists of 4
components when removing. If disassemble it, it could
not be assembled to original unit.

YH4
GRAND
VITARA
9-76 BODY SERVICE
1. Roof trim
2. Room light
3. Room light lens4. Clip
5. Screw
6. Room light harness
7. Marking tape
1. Seat belt
INSTALLATION
1) Set room light and clip to roof trim.
2) Set room light harness to roof trim with marking tape.
3) Reverse removal sequence to install roof trim.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.3 lb-ft)