2000 SUZUKI GRAND VITARA fuse and relay

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-27
1. ABS hydraulic unit/
control module assembly
2. ABS hydraulic unit/
control module
connector
1. ABS hydraulic
unit / control
module connector
DTC 57 (DTC C1057) ± SOLENOID AND PUMP MOTOR POWER SOURCE
CIRCUIT
DESCRIPTION
The ABS control module monitors the voltage at terminal ( ªA11º and ªA27º) of the fail-safe and pump motor relays
circuit constantly with the ignition switch turned ON. When all solenoid circuit voltages are below the specified value
or the voltage at the terminal ªA27º became below the specified value while the pump motor is operating, this DTC
will be set. As soon as the voltage rises to the specified level, the set DTC will be cleared.
INSPECTION
STEPACTIONYESNO
1Check battery voltage. Is it about 11 V or higher?Go to step 2.Check charging
system referring
to ªCHARGING
SYSTEMº section.
2Check ABS main fuse and connection. Is it in good
condition?Go to step 3.Repair and / or
replace fuse.
31) Ignition switch OFF.
2) Disconnect ABS hydraulic unit / control module
connector. (See Fig. 1)
3) Check proper connection to ABS hydraulic unit /
control module connector at terminal ªA27º.
4) If OK, then measure voltage between connector
terminal ªA27º and body ground.
Is it 10 ± 14 V?Substitute a
known-good
ABS hydraulic
unit / control
module assembly
and recheck.ªW / Blº circuit open.
Fig. 1

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-29
1. Ignition switch
2. ABS hydraulic unit/
control module assembly
3. ABS hydraulic unit/
control module connector
of harness 2
1. ABS hydraulic
unit / control
module connector
DTC 63 (DTC C1063) ± ABS FAIL-SAFE RELAY CIRCUIT
DESCRIPTION
The ABS control module monitors the voltage at the terminal of the solenoid circuit constantly with the ignition
switch turned ON. Also, immediately after the ignition switch is turned ªONº, perform an initial check as follows.
Switch the fail-safe relay in the order of ON
OFF
ON and check if the voltage at 6 solenoid circuit terminals
changes to High
Low
High. If anything faulty is found in the initial check and when the voltage at all solenoid
circuit terminals is low with the ignition switch turned ON and ABS not operated, this DTC will be set.
INSPECTION
STEPACTIONYESNO
1Check battery voltage. Is it about 11 V or higher?Go to step 2.Check charging
system referring
to ªCHARGING
SYSTEMº section.
2Check ABS main fuse and connection. Is it in good
condition?Go to step 3.Repair and / or
replace fuse.
31) Ignition switch OFF.
2) Disconnect ABS hydraulic unit / control module
connector. (See Fig. 1)
3) Check proper connection to ABS hydraulic unit /
control module at terminal ªA11º.
4) If OK, then measure voltage between connector
terminal ªA11º, and body ground.
Is it 10 ± 14 V?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.ªW / Blº circuit open
or short to ground.
Fig. 1

YH4
GRAND
VITARA
7B1-20 AUTOMATIC TRANSMISSION (4 A / T)
PRECAUTION IN DIAGNOSING TROUBLE

Don't disconnect couplers from PCM (ECM), battery cable from battery, PCM ground wire harness from engine
or main fuse before checking the diagnosis information (DTC, freeze frame data, etc.) stored in PCM memory.
Such disconnection will clear memorized information in PCM memory.

Using SUZUKI scan tool (Tech-1), or also generic scan tool for vehicle without monitor connector, the diagnostic
information stored in PCM memory can be checked and cleared as well. Before its use, be sure to read Operator's
(instruction) Manual supplied with it carefully to have good understanding of its functions and usage.

Priorities for diagnosing troubles (Only for vehicle without monitor connector)
If two or more diagnostic trouble codes (DTCs) are stored, proceed to the flow table of the DTC which was de-
tected earliest in the order and follow the instruction in that table.
If no instructions are given, troubleshoot diagnostic trouble codes according to the following priorities.
1. Diagnostic trouble codes (DTCs) other than DTC P0171 / P0172 (Fuel system too lean / too rich) and DTC
P0400 (EGR flow malfunction)
2. DTC P0171 / P0172 (Fuel system too lean / too rich) and DTC P0400 (EGR flow malfunction)

Be sure to read ªPrecautions for Electrical Circuit Serviceº in Section 0A before inspection and observe what is
written there.

PCM replacement
When substituting a known-good PCM, check for following conditions.
Neglecting this check may result in damage to good PCM.
± All relays and actuators have resistance of specified value.
± MAF sensor, MDP sensor, TP sensor and fuel tank pressure sensor are in good condition. Also, the power
circuit of these sensors is not shorted to the ground.

YH4
GRAND
VITARA
8
BODY ELECTRICAL SYSTEM 8-1
SECTION 8
BODY ELECTRICAL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
WIRING SYSTEM
(Harnesses, Connectors, Fuses, Relay, Switches, Grounds, System Circuit Diagram)Section 8A . . . . . . .
LIGHTING SYSTEMSection 8B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER INFORMATIONSection 8C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WINDOWS, MIRRORS, SECURITY AND LOCKSSection 8D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMMOBILIZER CONTROL SYSTEMSection 8F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
BODY ELECTRICAL SYSTEM 8-3

When installing the wiring harness, fix it with clamps so that no
slack is left.

When installing vehicle parts, be careful so that the wiring har-
ness is not interfered with or caught by any other part.

To avoid damage to the harness, protect its part which may con-
tact against a part forming a sharp angle by winding tape or the
like around it.

When replacing a fuse, make sure to use a fuse of the specified
capacity. Use of a fuse with a larger capacity will cause a damage
to the electrical parts and a fire.

Always be careful not to handle electrical parts (computer, relay,
etc.) in a rough manner or drop them.

YH4
GRAND
VITARA
Symbol
G : Green
G / Y : Green / Yellow G (Base Color)
G (Base Color)
Y (Stripe Color)G/Y
BODY ELECTRICAL SYSTEM 8-5
WIRE COLOR SYMBOLS
The wire color is abbreviated to the first (or first two) alphabet(s) of
each color.
There are two kinds of colored wire used in this vehicle. One is
single-colored wire and the other is dual-colored (striped) wire.
The single-colored wire uses only one color symbol (i.e. ªGº).
The dual-colored wire uses two color symbols (i.e. ªG / Yº). The first
symbol represents the base color of the wire (ªGº in the figure) and
the second symbol represents the color of the stripe (ªYº in the fig-
ure).
JOINT CONNECTOR (J / C)

Wiring of this vehicle employs joint connector (J / C) which divide
one wire into several different wires or combine several different
wires into one wire.

The joint connector is as shown in the figure.
FUSE BOX AND RELAY
Refer to Section 8A.

YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
6
5
1. Headlight assembly
2. Halogen bulb
3. Socket cover
4. Turn signal light bulb
5. Position light bulb
6. Turn signal light bulb socket
7. Position light bulb socket
8B-2 LIGHTING SYSTEM
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
HEADLIGHTS