2000 SUZUKI GRAND VITARA fuse and relay

YH4
GRAND
VITARA
8B-4 LIGHTING SYSTEM
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
HEADLIGHTS
TroublePossible causeCorrection
Only one light does not
light
Bulb blown

Headlight L or R fuse blown

Socket, wiring or grounding faultyReplace bulb
Replace fuse to check for short
Repair
Headlights do not light
Headlight L and R fuses blown

Lighting and dimmer switch faulty

Defective light relay

Wiring or grounding faultyReplace fuses to check for short
Replace switches
Replace light relay
Repair
Only one beam (ªHiº or
ªLoº) does not light
Bulb blown

Lighting or dimmer switch faultyReplace bulb
Replace switch
HEADLIGHTS WITH LEVELING SYSTEM (IF EQUIPPED)
TroublePossible causeCorrection
Both headlights do not
move
ªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)

Leveling switch faulty

Supply voltage too lowReplace fuse to check for short
Replace switch
Recharge or replace battery
One of headlights (either
Right or Left) does not
move
Socket, wiring or grounding faulty

Actuator faulty

Vehicle body around headlight deformed

Headlight ass'y itself deformedRepair
Replace actuator
Repair body
Replace headlight ass'y
TURN SIGNAL AND HAZARD WARNING LIGHTS
TroublePossible causeCorrection
Flash rate high or one side
only flashes
Incorrect bulb

One of light bulbs burnt out

Turn signal / hazard warning relay faulty

Open circuit or high resistance existing
Replace bulb
Replace
Replace relay
Repair
Oen circuit or high resistance existing
between turn signal / hazard warning
switch and lights on one side

Wiring or grounding faulty
Re air
Repair
No flashing
ªTURN / BACKº and / or ªHAZARDº fuse(s)
blown (Hard Top Model)
ªTRNº and / or ªHAZº fuse(s) blown
(Canvas Top Model)

Open circuit or high resistance existing
between battery and switch

Turn signal / hazard relay faulty

Combination switch or hazard switch faulty

Wiring or grounding faultyReplace fuse(s) to check for
short
Check bulb and check circuit
Replace relay
Replace switch
Repair
Flash rate low
Supply voltage too low

Turn signal / hazard relay faultyCheck charging system
Replace relay

YH4
GRAND
VITARA
8B-10 LIGHTING SYSTEM
1. Hazard relay
2. Junction box
3. Fuse box
Type A
Type B
3
3
2
HAZARD RELAY
INSPECTION
Connect battery and tester as shown.
Unless a continued click sound is heard, replace relay.

YH4
GRAND
VITARA
8C
INSTRUMENTATION / DRIVER INFORMATION 8C-1
GENERAL DESCRIPTION8C- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8C- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8C- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8C- 2. . . . . . . . . . . . . . . . .
Abbreviations 8C- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8C- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8C- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8C- 2. . . . . . . . . . . . . . . .
Combination Meter 8C- 2. . . . . . . . . . . . . . . . . . .
DIAGNOSIS8C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 4. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 4. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C- 4. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Remainder Warning Buzzer 8C- 5. . . . . . . Seat Belt Warning Light (If Equipped) 8C- 5. . .
Ignition Key Remainder Warning
Buzzer (If Equipped) 8C- 5. . . . . . . . . . . . . . . . .
Cigarette Lighter and Accessory Socket 8C- 5.
ON-VEHICLE SERVICE8C- 6 . . . . . . . . . . . . . . . .
Ignition (Main) Switch 8C- 6. . . . . . . . . . . . . . . . .
Combination Meter 8C- 7. . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 8. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 9. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C-11. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Key Remainder (If Equipped) /
Light Remainder Warning Buzzer 8C-12. . . . . .
Door Switch 8C-13. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Warning Light (If Equipped) 8C-13. . .
SECTION 8C
INSTRUMENTATION/DRIVER INFORMATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
1. Tachometer
2. Speedometer
3. Fuel level meter
4. Water temperature meter
5. Turn signal pilot light (LH)
6. 4WD indicator (if equipped)
7. ABS warning light (if equipped)
8. Immobilizer warning light (if equipped)
9. CHECK ENGINE light
10. Turn signal pilot light (RH)11. AIR BAG warning light (if equipped)
12. O / D OFF light (A / T vehicle only)
13. Fasten seat belt light (if equipped)
14. High beam light
15. Oil pressure warning light
16. Charge warning light
17. Brake and parking brake warning light
18. POWER indicator light (A / T vehicle only)
19. Shift position indicator (A / T vehicle, if equipped)or
CHECK
ENGINEor
ABS
8C-2 INSTRUMENTATION / DRIVER INFORMATION
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
COMBINATION METER

YH4
GRAND
VITARA
8D
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-1
GENERAL DESCRIPTION8D- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8D- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8D- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8D- 2. . . . . . . . . . . . . . . . .
Abbreviations 8D- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8D- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8D- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8D- 2. . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 2. . . . . . . . .
Front Wiper and Washer 8D- 2. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D- 3.
Power Door Lock and Keyless Entry
(If Equipped) System 8D- 4. . . . . . . . . . . . . . . .
DIAGNOSIS8D- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 5. . . . . . . . .
Front Wiper and Washer 8D- 5. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D- 5.
Rear Window Defogger (If Equipped) 8D- 5. . .
Power Window Control System 8D- 5. . . . . . . . .
Power Door Lock System (If Keyless
Entry is not Equipped) 8D- 6. . . . . . . . . . . . . . . Power Door Lock and Keyless Entry
System (If Keyless Entry is Equipped) 8D- 7. .
Power Door Mirror Control System 8D- 8. . . . . .
Door Mirror Heater (If Equipped) 8D- 8. . . . . . . .
Power Sliding Roof (If Equipped) 8D- 8. . . . . . .
Front Seat Heater (If Equipped) 8D- 8. . . . . . . .
ON-VEHICLE SERVICE8D- 9 . . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 9. . . . . . . . .
Front Wiper and Washer 8D- 9. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D-13.
Rear Window Defogger (If Equipped) 8D-16. . .
Power Window Control System 8D-18. . . . . . . . .
Power Door Lock System (If Keyless
Entry is not Equipped) 8D-20. . . . . . . . . . . . . . .
Power Door Lock and Keyless Entry
System (If Keyless Entry is Equipped) 8D-23. .
Power Door Mirror Control System 8D-30. . . . . .
Door Mirror Heater (If Equipped) 8D-31. . . . . . . .
Power Sliding Roof (If Equipped) 8D-32. . . . . . .
Front Seat Heater (If Equipped) 8D-33. . . . . . . .
SECTION 8D
WINDOWS, MIRRORS, SECURITY AND LOCKS
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
Front Wiper Assembly
Washer AssemblyFront Wiper Switch
8D-2 WINDOWS, MIRRORS, SECURITY AND LOCKS
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-3
1
A1 A2 A3 A4
A5 A6 A9 A10A7 A8
1. Coil antenna
2. Immobilizer Control Module
3. ECM/PCM
4. Immobilizer diagnostic coupler
4-1. Diagnostic output terminal
4-2. Ground terminal
5. Malfunction indicator lamp
6. Main relay
7. Ignition switch
8. Fuse
9. Main fuse
-10. To #9-pin in Data link connector
-11. To #7-pin in Data link connector
-12. To ABS control module
-13. Immobilizer indicator lamp
(Vehicle not equipped with monitor coupler)
-14. Monitor coupler (Vehicle not equipped
with immobilizer indicator lamp)) Terminal arrangement of Immobilizer
Control Module coupler (Viewed from
harness side)
B/R
BI
BI/B
B/W
V/Y
BI/B
B/W
B
V/W
V/W
BI
R
SbI
B
V/G
V
B
R/Y WIRE
SYMBOLWIRE
COLORabcdefghijklmn
1. Ignition key with built-in
transponder
1
1. Coil antenna
opqr
IGNITION KEY
The ignition key for the immobilizer control system has a built-in
transponder. Each transponder in the key has an each transmitting
code (Transponder code). The code will transmitted from the key
via the coil antenna to Immobilizer Control Module when the ignition
switch is turned ON.
COIL ANTENNA
The coil antenna is installed to the steering lock assembly. As it is
energized by Immobilizer Control Module, it transmits the trans-
ponder code of the ignition key to Immobilizer Control Module.

YH4
GRAND
VITARA
8G-14 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
In cabin
-1. Main fuse
-2. Main relay
-3. Immobilizer Control Module
-4. Immobilizer diagnostic coupler
4-1. Ground terminal
4-2. Diagnostic output terminal
-5. To ECM / PCM
TABLE A DTC IS NOT OUTPUT FROM DIAGNOSTIC OUTPUT TERMINAL
STEPACTIONYESNO
1Check voltage between A3 terminal
and body ground with ignition switch
turned ON.
Is it 10 ± 14V?Go to Step 2.ª(f)º wire open.
21) Connect voltmeter between A5
terminal and body ground.
2) Does voltmeter indicator deflect?Go to Step 3.
Poor A3, A5 or A7 connection.

ª(h)º wire of A7 terminal open.

ª(m)º wire between A5 terminal and
diagnostic output terminal of immobi-
lizer diagnostic coupler short.
If wire and connections are OK, substi-
tute a known-good Immobilizer Control
Module and recheck.
NOTE:
After replacing with a known-good
Immobilizer Control Module, register
ECM/Immobilizer Control Module
code in ECM / PCM and Transponder
code and ECM/Immobilizer Control
Module code in Immobilizer Control
Module by performing procedure
described in ªProcedure after Immo-
bilizer Control Module Replace-
mentº section.
31) Connect voltmeter between diag-
nostic output terminal of immobiliz-
er diagnostic coupler and body
ground.
2) Is it possible to read DTC by check-
ing deflection of voltmeter indicator?ª(n)º wire of ground
terminal for immo-
bilizer diagnostic
coupler open.ª(m)º wire between A5 terminal and diag-
nostic output terminal of immobilizer
diagnostic coupler open.