2000 SUZUKI GRAND VITARA Console

YH4
GRAND
VITARA
7A-6 MANUAL TRANSMISSION (TYPE 1)
3, (a)
1. Coupler
2. Clamp3. 4WD switch
4. Boot No. 2
1. Back up light switch
2. 4WD switch
1. Back up light switch coupler
2. Front propeller shaft
SWITCHES
TRANSFER 4WD SWITCH
1) Remove console box and lift transmission control lever boots
No. 2 and No. 3. (Refer to page 7A-4.)
2) Remove transfer control lever boot No. 2, unclamp wiring on
transfer case to free it and pull off coupler.
3) Replace switch and connect as it was.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft)
4) Turn ON ignition switch, shift transfer shift control lever to 4WD
position and check that indicator lights. Turn OFF switch after
checking.
NOTE:

When removing and reinstalling switch, use care not to let
dust enter transfer box inside.

Make sure to reset clamp for wiring which is located
where invisible directly.

It is recommended to work on transfer shift control lever
boot No. 1 from underside of vehicle on lift.

Identify this switch by its leg part which is different for that
of back up light switch.
BACK UP LIGHT SWITCH
WARNING:
Refrain from work while exhaust center pipe is hot.
REMOVAL AND INSTALLATION
NOTE:
When replacing switch, use care not to let dust enter transmis-
sion through switch hole.
1) Lift up vehicle.
2) Remove coupler(s) for switch wiring.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-3
1. Torque converter
2. Overdrive input shaft
3. Oil pump
4. Overdrive brake
5. Overdrive clutch
6. Forward clutch input shaft
7. Forward clutch
8. Direct clutch
9. One-way clutch
10. Second coast brake
11. Second brake
12. Reverse brake
13. Front planetary gear
14. Rear planetary gear
15. Overdrive planetary gear
GENERAL DESCRIPTION
This automatic transmission is a full automatic type with 3-speed plus overdrive (O / D).
The torque converter is a 3-element, 1-step and 2-phase type and is equipped with an electronically controlled
lock-up mechanism. The gear shift device consists of 3 sets of planetary gear units, 3 disc type clutches, 4 disc
type brakes and 3 one-way clutches. The gear shift is done by selecting one of 6 positions (ªPº, ªRº, ªNº, ªDº, ª2º
and ªLº) by means of the select lever installed on the floor. On the shift knob, there is an overdrive (O / D) cut switch
which allows shift-up to the overdrive mode (except at 4L) and shift-down from the overdrive mode. Also, by using
the P / N change switch located on the console box, it is possible to select the gear change timing of 2 modes, nor-
mal and power.

YH4
GRAND
VITARA
7B1-36 AUTOMATIC TRANSMISSION (4 A / T)
Switch ON
positionSwitch OFF
positionSwitch ON
position
Switch OFF
position
DIAGNOSTIC FLOW TABLE B-2 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-1 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check O / D cut Switch Position.
Is O / D cut switch turned OFF (Is switch button at OFF
position)?Go to Step 2.Turn O / D cut switch
OFF.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªO / D OFFº lamp come ON steadily?ªW / Bº circuit shorted
to ground.Go to Step 3.
3Check O / D cut Switch Circuit.
1) Check resistance between terminal E61-33
(G16 / J20 engines) or E61-14 (H25 engine) of
disconnected PCM connector and body ground with
O / D cut switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check O / D cut Switch for Operation.
1) Remove console box.
2) Disconnect O / D cut switch connector.
3) Check continuity between switch terminals under
each condition below.
Switch OFF position: No continuity
Switch ON position: Continuity
Is check result satisfactory?ªY / Rº circuit shorted
to ground.Replace O / D cut
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
1. Manual selector assembly
(Select lever assembly)
2. Manual lever assembly
3. Select cable bracket
4. Select indicator
5. Slide cover
6. Select lever knob7. Spring
8. Knob button
9. Shift lock solenoid rod
10. Shift lock solenoid
11. Cover
12. Illumination lamp
13. Interlock cam
1. Interlock cam pin
(only for new selector assembly) Tightening Torque
(a): 18 N
.m (1.8 kg-m, 13.5 lb-ft)1. Manual lever
assembly
2. Select indicator
assembly
3. Illumination lamp
assembly
4. Bulb filter
5. Bulb
6. Knob assembly
7. Shift lock solenoid
Type-1 Type-2
Type-1
7B1-62 AUTOMATIC TRANSMISSION (4 A / T)
MANUAL SELECTOR ASSEMBLY
REMOVAL
1) Disconnect negative cable at battery.
2) Remove console box.
3) Disconnect connector for illumination lamp, shift lock solenoid
and overdrive OFF switch.
4) Disconnect interlock cable from interlock cam of selector as-
sembly.
5) Remove selector assembly mounting bolts.
6) Disconnect select cable from lever of selector assembly.
INSTALLATION
NOTE:
New selector assembly of Type-1 is supplied with held inter-
lock cam at interlock cable connecting position with pin. Re-
move this pin after connecting interlock cable to interlock cam
and tightening cable nut.
Reverse removal procedure to install noting the followings.

Connect interlock cable end to cam referring to steps 2) to 8) of
ªInterlock Cable Installationº section.

Upon completion of installation, confirm that brake (key) interlock
system operates properly.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-71
Ignition switch side
1. Ignition switch assembly
2. Clamp screw
3. Interlock cable
Select lever side
Type-1
1. Inner end of interlock cable
2. Interlock cam (or key release cam)
3. Stud bolt4. Cam boss
5. Claw
Select lever side
Type-2
KEY INTERLOCK CABLE
NOTE:
Don't bend interlock cable excessively when removing and
installing it, or system will not operate correctly.
Removal
1) Disconnect negative (±) cable from battery.
2) If equipped with air bag system, disable air bag system.
Refer to ªDisabling Air bag Systemº in Section 10B.
3) Remove steering column hole cover.
4) Tilt steering column if steering column is adjustable.
If no adjustable, loosen steering column bolts.
5) Remove steering column cover.
6) Remove interlock cable clamp screw located at ignition switch
assembly.
7) Disconnect interlock cable inner end.
(Ignition switch side.)
8) With console box removed, take out interlock cable by loosening
lock nuts.
9) Detach cable end from interlock cam (or key release cam) while
pressing claws of interlock cam boss. At this time, be careful not
to cause damage to its claws.

YH4
GRAND
VITARA
1. Ignition switch assembly
2. Clamp screw
3. Outer end
1. Interlock cable
2. Steering column
3. Steering column
holder
Type-1
1. Interlock cam
2. Lever plate
3. Interlock cable
4. Pin with 4 mm (0.15 in.) dia.
7B1-72 AUTOMATIC TRANSMISSION (4 A / T)
Installation
1) Shift select lever to ªNº range and turn ignition key to ªACCº
position.
2) Connect inner end of interlock cable to key interlock lever (Igni-
tion switch side).
3) Install outer end bracket of interlock cable to ignition switch as-
sembly, and tighten screw to specified torque.
Tightening Torque
(a): 2.2 N
.m (0.22 kg-m, 1.5 lb-ft)
4) Pass and connect interlock cable as shown at the left figure.
TYPE-1
5) Fix interlock cam by inserting pin with about 4 mm (0.15 in.) dia.
into holes of cam and lever plate.
6) Install cable end to interlock cam and stud bolt and after making
sure that cable outer is pushed in arrow direction B by leaf
spring, tighten mounting nut to specified torque. Remove pin.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
7) Turn ignition key to ªACCº position and shift select lever to ªNº
range, and check for the followings.
a. When select lever is shifted at ªPº range with knob button
depressed, ignition key can not be turned from ªACCº to
ªLOCKº position.
b. When knob button is released, ignition key can be turned to
ªLOCKº position.
c. When ignition key is at ªLOCKº position, select lever can not
be shifted from ªPº to any other range.
8) Install console box.
9) Install steering column cover.
10) Adjust steering column or tighten steering column bolts.
11) Install steering column hole cover.
12) If equipped with air bag system, enable air bag system.
Refer to ªEnabling Air bag Systemº in Section 10B.

YH4
GRAND
VITARA
1. Inner end of interlock cable
2. Key release cam
1. Key release cam
2. Cable outer(a)
Type-2
Type-2
AUTOMATIC TRANSMISSION (4 A / T) 7B1-73
TYPE-2
5) With key release cam set as shown at the left figure, connect
inner end of interlock cable to key release cam. (Select lever
side.)
6) Move key release cam so that it is set at such angle as shown
at the left figure and with special tool inserted in hole A , fix key
release cam.
Special Tool
(A): 09925-78210 (6 mm)
7) With key release cam fixed with special tool, install cable outer
to bracket and after making sure that cable outer is pushed in
arrow direction B by leaf spring, tighten mounting nut to speci-
fied torque. Remove special tool.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
8) Turn ignition key to ªACCº position and shift select lever to ªNº
range, and check for the followings.
a. When select lever is shifted at ªPº range with knob button
depressed, ignition key can not be turned from ªACCº to
ªLOCKº position.
b. When knob button is released, ignition key can be turned to
ªLOCKº position.
c. When ignition key is at ªLOCKº position, select lever can not
be shifted from ªPº to any other range.
9) Install console box.
10) Install steering column cover.
11) Adjust steering column or tighten steering column bolts.
12) Install steering column hole cover.
13) If equipped with air bag system, enable air bag system.
Refer to ªEnabling Air bag Systemº in Section 10B.

YH4
GRAND
VITARA
7B1-74 AUTOMATIC TRANSMISSION (4 A / T)
1. Boot No.2
2. Boot cover
1. Boot clamp
2. Boot No.1
3. Gear shift control lever
1. Boot No.2
2. Transfer shift control
lever
3. Transfer shift lever case4. Transfer shift control
case cover
5. Boot No.1
1. A / T throttle cable
2. Adjusting nut
3. Lock nut
G16 / J20 H25
DISMOUNTING OF TRANSMISSION (WITH
TRANSFER IF EQUIPPED)
IN CABIN
1) Remove console box.
NOTE:
To remove clip, push in its center pin first.
2) Remove boot cover and boot No.2. (if equipped)
3) Remove boot clamp and then remove boot No.1 from transfer
gear shift lever case. (if equipped)
4) With transfer shift control case cover pushed down with fingers,
turn it to counterclockwise and take out shift control lever. (if
equipped)
IN ENGINE ROOM
1) Remove battery, dipstick and oil filler tube.
2) Disconnect A
/
T throttle cable from throttle cam and bracket.
3) Remove starter motor. But don't disconnect its wiring harness.
4) Remove transmission to engine bolt and nut.