Page 51 of 118
Downloaded from www.Manualslib.com manuals search engine FUEL MIXTURE
Priming catalytic converter
12
12-13
REFITTING
Fit the priming catalytic converter (or pre-catalytic
converter) to the turbocharger.
Fit:
– the pre-catalytic converter stay,
– the mounting nuts.
Tighten all the nuts and mounting bolts.
Refit the exhaust downpipe.
Replace the seals.
Page 52 of 118

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
Specifications
13
113
DIESEL EQUIPMENT
Specifications
Vehicle GearboxEngine
Depollution
standard
Type IndexBore
(mm) Stroke
(mm) Cubic
capacity
(cm
3)Compres-
sion ratioCatalytic
converter
XA05 JC5 F9Q 732 80 93 1 870 19/1◊ C103 Euro 2000
ENGINE SPEED (rpm) SMOKE DENSITY
IDLING SPEED Max. - no loadMax. - under
loadHomologation value Max. - Max
835 ± 50 4,700 ± 150 4,500 ± 100
1.5 m
-1 (46 %) 3 m-1 (70 %)
DESCRIPTION BRAND/TYPE SPECIAL NOTES
High pressure pumpBOSCH
CR/CP153/R65/10-15Pressure from 250 to 1350 bars
Supercharging pump (low
pressure)BOSCHPressure from 2.5 to 4 bars
Flow: 80 to 100 litres/hour minimum
Diesel pressure sensor BOSCHFitted to the injection rail
Resistance: tracks 1,2 and 1,3 = 4.3 MΩ
tracks 2,3 = 1050 Ω
Injectors BOSCHSolenoid injector
Resistance: < 2 Ω
Maximum pressure 1525 bars
Pressure regulator - Integrated with the high pressure pump
Resistance: ≈ 5 Ω at 20˚ C
Injection computer BOSCH128 track computer
Pre-postheating unit NAGARES BED/7With pre-postheating function controlled by the
injection computer
Heater plugsBERU
or
CHAMPIONResistance: 0.6 Ω connector removed
Accelerator potentiometer CTSDouble track potentiometer
Track resistance ≈ 1.7 Ω
Air intake temperature sensor SIEMENSintegrated in the flow meter
Resistance between 100 Ω and 40 Ω
13-1
Page 62 of 118
Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
Location of components
13
13-11
16181R
7
8
9Cylinder marking sensor
Turbocharger
Priming catalytic converter
16155R2
11
12
13
14EGR solenoid valve
Turbo regulation solenoid
Turbocharger pressure sensor
Preheating unit
16869R3
15
16
17Injection computer
Fuel filter
Repriming fuel cock
16870R2
Page 102 of 118
Downloaded from www.Manualslib.com manuals search engine STARTING - CHARGING
Starter
16
16-5
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Remove (for the Scénic):
– the front right hand grille as well as the mounting
bolts of the left hand grille,
– the closure panel of the scuttle,Remove (all types):
– the turbocharging air ducts between the exchanger
and the engine,
– the pre-catalytic converter mountings to the turbo.
Loosen the exhaust pipe clamp mounting.
Remove:
– the pre-catalytic converter stay (1),
– the catalytic converter mountings on the precatalytic
converter and remove this by moving the engine
towards the cooling system,
– the oil return pipe (8),
– the starter electrical connections.
– the starter mountings,
– the starter motor.
REFITTING
To remove, proceed in the reverse order.
Check the presence of the starter motor centring
dowel.
11020R
11036R2
16155R
Page 109 of 118

Downloaded from www.Manualslib.com manuals search engine EXHAUST
Catalytic converter
19
19-7
1419 EXHAUST
Catalytic converter
Disconnect the battery and put the vehicle on a two
post lift.
Fit a flywheel immobiliser.
Loosen the catalytic converter/precatalytic converter
mountings.
Fit tool Tav. 1233-01 replacing the bolts of the sub-
frame one by one.Remove:
– the bolts of the sub-frame tie-rods,
– the nut and eccentric bolt of the steering shaft
yoke (1),
– the torque reaction arm.
Lower the sub-frame to a height of 40 mm at the front
and 60 mm at the rear.
Remove the exhaust mounting clip.
Remove the mounting nuts of the catalytic converter
and remove it, taking care not to damage the heat
shields.
REFITTING
Proceed in the reverse order from removal.
WARNING: all damaged heat shields must be
replaced to prevent the risk of fire. TIGHTENING TORQUES (in daN.m)
Engine tie bar bolt 6.2
Steering shaft yoke bolts 3
Engine sub-frame bolts
–front ∅ 10
–rear ∅ 12 6.2
10.5
Three point flange nuts 2
Sub-frame - side member tie rod bolts 3
15870R
97390-1R2