2000 MITSUBISHI MONTERO stop start

3 MSB-00E00-505
3. Details:
Contents of Attachment are to be added to GROUP 00 (GENERAL).
PRECAUTIONS BEFORE SERVICE
LEARNING FUNCTION OF GDI ENGINE
1. Purpose
On the GDI engine equipped cars, when replacement of the ECU (for engine control) or resetting
of the battery* has been performed, an idle learning function of the ECU (for engine control) will
be required.
The idle learning function will be completed by running the engine at idle by the following procedure.
NOTE:
*: Disconnection of ECU (for engine control) battery backup power supply (disconnection of battery
terminals or ECU connectors)
2. Idle Learning Procedure
(1) Start the engine, and warm up the engine until its coolant temperature reaches 85°C or higher.
When the engine coolant temperature is 85°C or higher, you have only to turn the ignition
switch to the ON position.
(2) Turn the ignition switch to the LOCK (OFF) position, and stop the engine.
(3) After lapse of ten or more seconds, restart the engine.
(4) Run the engine at idle for ten minutes under the following conditions.
DTransmission: Neutral (P range for automatic transmission)
DAir conditioner and heater: Not operational
DEngine coolant temperature: 83°C or higher
(5) Stop the engine.
(6) Restart the engine, and run it at idle for ten minutes under the following condition.
DTransmission: Neutral (P range for automatic transmission)
DAir conditioner: Operational (Temperature set at “maximum cool”, fan at high speed, and
windows fully opened)
DEngine coolant temperature: 83°C or higher
(7) Repeat steps (5) and (6).
NOTE:
1) When the atmospheric temperature is 20°C or more and the air conditioner has continuously
been operated, step (7) may be omitted.
2) During idling operation of the engine in steps (4) and (6), when engine operation switches
from lean operation to stoichiometric operation, engine stall can occur. In this case, clean the
throttle body (throttle valve) thoroughly, and then repeat step (1) and the subsequent steps.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

ENGINE <6G7> -General Information/Service Specifications11A-3
GENERAL INFORMATION
Items6G74-GDI
Total displacement ml3,497
Bore´Stroke mm93´85.8
Compression ratio10.4
Combustion chamberPentroof + ball-in-piston
Camshaft arrangementDOHC
Number of valveIntake12
Exhaust12
Valve timingIntakeOpeningBTDC 8_
ClosingABDC 56_
ExhaustOpeningBBDC 48_
ClosingATDC 16_
Fuel systemElectronically controlled multipoint fuel injection
Rocker armRoller type
Auto-lash adjusterEquipped
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
Basic ignition timing5_BTDC±3_-
Ignition timingApprox. 20_BTDC*1-
Idle speed r/min600±100*1-
CO contents %0.5 or less-
HC contents ppm100 or less-
Compression pressure (at engine speed of 280 r/min) kPa1,275980
Compression pressure difference of all cylinders kPa-Max. 98
Intake manifold vacuum kPa-Min. 56*2
Auto tensioner rod depth (mm)Within 1-
Timing belt tension torque N×m4.4-
Auto-tensioner rod protrusion amount mm3.8 - 5.0-
NOTE
*1: Indicates the value measured within 4 minutes since the engine was started.
*2: Indicates the value when more than 4 minutes have passed since the engine was started.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-10
Code No. Diagnosis item
P0206No.6 injector system
P0220LAccelerator pedal position sensor (1st channel) system
P0225LThrottle position sensor (2nd channel) system
P0300LIgnition coil (power transistor) system
P0301No.1 cylinder misfire detected.
P0302No.2 cylinder misfire detected.
P0303No.3 cylinder misfire detected.
P0304No.4 cylinder misfire detected.
P0305No.5 cylinder misfire detected.
P0306No.6 cylinder misfire detected.
P0335Crank angle sensor system
P0340Camshaft position sensor system
P0403EGR valve system
P0420Catalyst malfunction
P0443Purge control solenoid valve system
P1200Injector driver system
P1220LElectronic-controlled throttle valve system
P1221LThrottle valve position feedback system
P1222LThrottle control servo system
P1223LCommunication line system with throttle valve controller
P1225LAccelerator pedal position sensor (2nd channel) system
P1226LThrottle valve controller system
NOTE
1. If the engine warning lamp illuminates because of a malfunction of the engine-ECU, communication
between MUT-
IIand the engine-ECU is impossible. In this case, the diagnosis code cannot be read.
2. After the engine-ECU has detected a malfunction, the engine warning lamp illuminates when the
engine is next turned on and the same malfunction is re-detected. However, for items marked with
a“
L” in the diagnosis code number column, the engine warning lamp illuminates only on the first
detection of the malfunction.
If diagnosis code P0120, P0220, P0225 or P1225 is set, the engine warning lamp will flash. If the
1st and 2nd channels of the throttle postion sensor or the acccelerator pedal position sensor fail
at the same time, the engine warning lamp will also flash.
3. After the engine warning lamp illuminates, it will be switched off under the following conditions.
(1) When the engine-ECU monitored the power train malfunction three times* and met set condition
requirements, it detected no malfunction.
*: In this case, “one time” indicates from engine start to stop.
(2) For misfiring malfunction, when driving conditions (engine speed, engine coolant temperature,
etc.) are similar to those when the malfunction was first recorded.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-82
OK
Check that air is sucked in the air intake system.
DBroken intake manifold gasket
DDamaged vacuum hose
DDamaged air intake hose
From the previouspage
OK
MUT-
IIData list
27 Power steering fluid pressure switch (Refer to P.13A-105.)NGCheck the power steering fluid pressure switch system. (Refer
to P.13A-102, Inspection procedure 30.)
OK
MUT-
IIData list
28 A/C switch (Refer to P.13A-105.)NGCheck the A/C switch and A/C relay system. (Refer to P.13A-102,
Inspection procedure 31.)
OK
MUT-
IIData list
67 Stoplampswitch (Refer to P.13A-105.)NGCheck the stoplampswitch. (Refer to P.13A-103, Inspection proce-
dure 32.)
OK
MUT-
IIData list
31 Small lampswitch (Refer to P.13A-105.)NGCheck the smalllampswitch system. (Refer to P.13A-104, Inspec-
tion procedure 33.)
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-105.)NGCheck the EGR valve. (Refer to P.13A-60, code No. P0403.)
OK
NG
Check that the crankanglesensor andtiming beltcover are properly
installed.
OK
Check ignition coil spark for each cylinder.
(1) Remove the ignition coil.
(2) Install a new sparkplug to the removed ignitioncoil.
(3) Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
(4) Earth the sparkplug electrodesecurely.
(5) Check that the sparkplug igniteswhen theengine iscranked.NGReplace the ignition coil.
OK
Check trouble symptom.
Check all the following items in that order.
(1) Spark plugs
(2) Exhaust gas emission control system
(3) EGR system
(4) Compression pressure
(5) Foreign material (such as water or kerosine)entered the fuel
line.
(6) Air is sucked in the air intake system, or EGR gas leaks.
DDamaged intake manifoldgasket
DDamaged air intake hose
DDamaged vacuum hose
DFaulty EGR valve seat
OK
MUT-
IIData list
11 Oxygen sensor (front)
OK:
0 - 400 mV and 600 - 1,000 mV alternates when the
engine is idling(wait for four minutes after theengine
started).NG
NG
Repair
Measure fuel high-pressure between the fuel pump (highpressure)
and injector. (Refer to P.13A-224.)
Clean around the throttle valve. (Refer to P.13A-220.)
NG
Check ignition timing. (Refer to GROUP 11A - Engine Adjustment.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-109
Item
No.Reference
page Inspection
procedure
No. Normal condition Requirements Check items
77Accelerator
pedal positionIgnition switch: ONRelease the accel-
erator pedal.985 - 1085 mVCode
No.P122513A-68
sensor (2nd
channel)
Depress the accel-
erator pedal gradu-
ally.Increases in re-
sponse to the ped-
al depression
stroke.
Depress the accel-
erator pedal fully.4,000 mV or more
78Accelerator
pedal positionIgnition switch: ONRelease the accel-
erator pedal.985 - 1085 mVCode
No.P022013A-50
sensor (1st
channel) *3Depress the accel-
erator pedal gradu-
ally.Increases in re-
sponse to pedal
depression stroke.
Depress the accel-
erator pedal fully.4,200 - 4,800 mV
79Throttle posi-
tion sensorDEngine coolant
temperature:Release the accel-
erator pedal.400 - 800 mVCode
No.012013A-25
(1st channel)80 - 95_C
DIgnition switch:
ON (Engine
stopped)
Depress the accel-
erator pedal gradu-
ally.Increases in re-
sponse to pedal
depression stroke.
4,600 - 5,200 mV4,200 - 4,800 mV
Engine: AfterNo load450 - 1,000 mV
warm-up, idling
A/C switch: OFF®
ONIncreases by 100 -
600 mV.
99Fuel injection
modeEngine: After warm
upIdling (after four
minutes or more
have passed since
engine start)Lean compression--
2,500 r/minStoichiometric
metric feedback
Sudden racing after
idle positionOpen loop


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-112
Terminal
No.Normal condition Check requirements (engine condition) Check item
16Purge control solenoid valveDEngine cool-Engine: stoppedSystem voltage
ant tempera-
ture:
80 - 95_C
DIgnition
switch: ON
Engine: Start the
engine, and then
increase engine
speed up to 3,500
r/min.Voltage decreases.
18Condenser fan relayCondenser fan is not operating.System voltage
Condenser fan is operating.0-3V
20Fuel pump relayIgnition switch:Engine: stoppedSystem voltage
ON
Engine: idling0-3V
21A/C relayDEngine: idlingSystem voltage, or changes
DA/C switch: OFF®ON
(Compressor is operating)from momentarily 6 V or
more to 0®3V
31Engine warning lampIgnition switch: OFF®ON0-3V®System voltage
(after several seconds)
41Sensor power supplyIgnition switch: ON4.5 - 5.5 V
42Power supply to accelerator
pedal position sensor (1st
channel)Ignition switch: ON4.5 - 5.5 V
43Crank angle sensorEngine: Cranking0.4 - 4.0 V
Engine: Idling1.5 - 2.5 V
44Engine coolant temperature
sensorIgnition switch:
ONEngine coolant
temperature: 0_C3.2 - 3.5 V
Engine coolant
temperature:
20_C2.3 - 2.9 V
Engine coolant
temperature:
40_C1.5 - 2.1 V
Engine coolant
temperature:
80_C0.4 - 1.0 V
45Engine ignition signalEngine: 3,000 r/min0.3 - 3.0 V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-195
Inspection procedure 32
Stop lamp switch system
Probable cause
The engine-A/T-ECU determines whether the brakepedal is depressed or not.
The engine-A/T-ECU selects a fuel injectionmode by determining thebrake
operation according to this information.DMalfunction of the stoplampswitch
DImproper connector contact,opencircuit or
short-circuited harness wire
DMalfunction of the engine-A/T-ECU
NG
Check the following connectors:
D-26 , D-27, D-124 NG
Repair
OK
Check the trouble symptoms.
OK
Check the following connector:
D-122NG
Repair
Stoplampswitch check (Refer to
GROUP 35 - Brake Pedal.)NG
Replace
OK
Measure at stoplampswitch
connector D-136.
DDisconnect the connector, and
measure at the harness side.
DThe voltage between terminal 2
and earth
OK
System voltageOKMeasure at the engine-A/T-ECU
connector D-122.
DDisconnect the connector, and
measure at the harness side.
DThe voltage between terminal 123
and earth
(Ignition switch: ON)
OK
0 - 3 V (when the brake
pedal is not depressed)
System voltage (when the
brakepedal is depressed)NG
NG
Repair OK
Check the trouble symptoms.
NG
Check the harness wire between the
engine-A/T-ECU and the stoplamp
switch, and repair if necessary.
NG
Check the harness wire between the
battery and the stoplampswitch,
and repair if necessary.
OK
Check the trouble symptoms.NGReplace the engine-A/T-ECU.
Check the following connectors:
D-26 , D-33, D-128, D-136,
D-124 , E-13
Inspection procedure 33
Small lamp switch system
Probable cause
The engine-A/T-ECU determines whether the smalllampswitch is on or off.
According to that information, the engine-A/T-ECU controls alternator output
current when the vehicle is started.DImproper connector contact,opencircuit or
short-circuited harness wire in thetaillamprelay
circuit.
DMalfunction of the engine-A/T-ECU
OK
Check the following connector:
D-121NGReplace
Measure at engine-A/T-ECU connector D-121.
DDisconnect the connector, and measure at the harness
side.
DThe voltage between terminal 86 and earth (Lighting
switch: ON)
OK:
System voltageNGCheck thetaillampcircuit. (Refer to ELECTRICAL WIRING.)
OK
Check the trouble symptoms.
NG
Replace the engine-A/T-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-199
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
14Throttle
positionDEngine: After hav-
ing warmed upRelease the acceler-
ator pedal.4,000 mV or moreCode No.
1413A-137
sensor (2nd
channel)DIgnition switch: ON
(Engine: Stopped)
Depress the acceler-
ator pedal gradually.Voltage
decreases in
response to the
pedal depression.
Depress the acceler-
ator pedal fully.400 - 600 mV
16System
voltageIgnition switch: ONSystem voltageProcedure
No. 2513A-190
18Cranking
signal (igni-Ignition switch: ONEngine: StoppedOFFProcedure
No.2713A-191
signal (igni-
tion switch:
ST)
Engine: CrankingON
No.27
21Engine cool-
ant temper-
ature sensorIgnition switch: ON or
with engine runningWhen engine coolant
temperature is
-20_
C-20_
CCode No.
2113A-138
When engine coolant
temperature is 0_
C0_
C
When engine coolant
temperature is 20_
C20_
C
When engine coolant
temperature is 40_
C40_
C
22Crank angle
sensorDEngine: Cranking
DTachometer: Con-
nectedCompare the
tachometer with the
MUT-IIreading.IdenticalCode No.
2213A-140
DEngine: Idling
DIdle position
switch: ON
DWithin six minutesWhen engine coolant
temperature is
-20_
C1,250 - 1,450
r/min
DWithin six minutes
after engine
starting (Onlywhen
engine coolant
When engine coolant
temperature is 0_
C1,100 - 1,300
r/min
engine coolant
temperature is
80
_C)
When engine coolant
temperature is 20_
C1,000 - 1,200
r/min
When engine coolant
temperature is 40_
C900 - 1,100 r/min
When engine coolant
temperature is 80_
C550 - 650 r/min


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk