2000 MITSUBISHI MONTERO fuel

DIESEL FUEL <4M4> -Troubleshooting13C-37
ACTUATOR TEST TABLE
Item
No.Check itemDrive Con-
tentsInspection
conditionsValue to be determined
as normalCode No.
or inspec-
tion proce-
dure No.Reference
page
02Glow plug relayTurning theIgnition switch:Battery charge is––
relay from
OFF to ON orONenergized to the glow
plug when the glow
from ON to
OFFplug relay is ON.
03A/C compressorTurning theIgnition switch:The A/C compressor––
relayrelay from
OFF to ON orONclutch makes an
audible sound.
from ON to
OFF
11Timing control
valveTurn the
timing control
valve to ONDIgnition
switch: ON
DEngine:
IdlingMakes an audible
soundCode
No.4313C-20
12Turn the
timing control
valve to OFF
Idling
DTimer piston
position
sensor:
Normal
15Glow lampTurn the glow
lamp on or offIgnition switch:
ONThe glow lamp turns
on––
16Warning lampTurn the
warning lamp
on or offIgnition switch:
ONThe warning lamp
turns onProcedure
No.3, 413C-25
22Condenser fan
relayTurning the
relay from
OFF to ON or
from ON to
OFFIgnition switch:
ONThe condenser fan
rotates.––
23Main throttle
solenoid valveTurn the
solenoid
valve from
OFF to ON or
from ON to
OFFDIgnition
switch: ON
DVehicle
speed:
0 km/h
DEngine
speed:
1,000 r/min
or lowerMakes an audible
soundCode
No.4113C-19
24Sub throttle
solenoid valveTurn the
solenoid
valve from
OFF to ON or
from ON to
OFFDIgnition
switch: ON
DVehicle
speed:
0 km/h
DEngine
speed:
1,000 r/min
or lowerMakes an audible
sound––


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

DIESEL FUEL <4M4> -Troubleshooting13C-38
Item
No.Reference
page Code No.
or inspec-
tion proce-
dure No. Value to be determined
as normal Inspection
conditions Drive Con-
tents Check item
25GE actuatorTurn the GE
actuator to
ONDIgnition
switch: ON
DEngine
speed:
0 r/min orMakes an audible
soundCode
No.4813C-21
26Turn the GE
actuator to
OFF
0 r/min or
lower
DControl
sleeve posi-
tion sensor:
Normal
27Fuel cut solenoid
valveTurn the
solenoid
valve to ONDIgnition
switch: ON
DVehicle
speed:
0 km/hMakes an audible
sound––
28EGR solenoid
valve No.1Turn the
solenoid
valve to ONDIgnition
switch: ON
DVehicleMakes an audible
sound––
29Turn the
solenoid
valve to ONspeed:
0 km/h
30EGR solenoid
valve No.2Turn the
solenoid
valve from
OFF to ON or
from ON to
OFFDIgnition
switch: ON
DVehicle
speed:
0 km/hMakes an audible
sound––
33PTC heaterSwitch the
PTC heater
relay ON/
OFF.DIgnition
switch: ONVoltage on the ECU
terminal No.9: 0 - 1V––
34Middle position
of GE actuatorHold the
injection
governor in
its middle
position.DIgnition
switch: ONWhen the crankshaft
is turned clockwise
during the adjustment
of the injection timing,
the injection pipes
spray out fuel.Code
No.4813C-21


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

DIESEL FUEL <4M4> -Troubleshooting13C-40
Terminal
No.Normal condition: Inspection conditions (engine status) Check item
36Selector switch be-
tween A/T and M/TIgnition switch: ON0-1V
37Inhibitor switchIgnition switch: ON
(Engine stops)Set the selector lever to P
or N0-1V
Set the selector lever to D,
2, L, or RSystem voltage
39Stop lamp switchDepress the brake pedalSystem voltage
40Brake switchDepress the brake pedal0-1V
46Control relayIgnition switch: ON0-1V
Ignition switch: ON®OFF (in about 8 seconds)System voltage
51Engine speed sensor
(backup)Engine: Idling1.5 - 2.5 V
55Accelerator pedal posi-
tion sensor (sub)Ignition switch: ONAccelerator pedal: Idling
position0.9 - 1.1 V
Accelerator pedal: Fully
opened position4.1 V or higher
71Ignition switch-STEngine: Cranking8 V or higher
74Control sleeve positionIgnition switch: ON (Engine stops)2.2 - 2.7 V
73sensor2.0 - 4.0 V
752.0 - 4.0 V
76Timer piston positionIgnition switch: ON (Engine stops)2.2 - 2.7 V
77sensor2.0 - 4.0 V
782.0 - 4.0 V
80Back-up power supplyIgnition switch: OFFSystem voltage
82Ignition switch-IGIgnition switch: ONSystem voltage
83Engine coolant tem-
perature sensorIgnition switch: ONEngine coolant tempera-
ture: 0_C3.4 - 4.5 V
Engine coolant tempera-
ture: 20_C2.6 - 3.6 V
Engine coolant tempera-
ture: 40_C1.8 - 2.5 V
Engine coolant tempera-
ture: 80_C0.7 - 1.1 V
84Accelerator pedal posi-
tion sensor (main)Ignition switch: ONAccelerator pedal: Idling
position0.9 - 1.1 V
Accelerator pedal: Fully
opened position4.1 V or higher
85Boost pressure sensorIgnition switch: ON (760 mmHg)1.2 - 1.6 V
86Vehicle speed sensorDIgnition switch: ON
DMove the vehicle forward slowly0V«5 V (repeat the
change)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

DIESEL FUEL <4M4> -Troubleshooting13C-41
Terminal
No.Normal condition: Inspection conditions (engine status) Check item
87Fuel temperature sen-Ignition switch: ONFuel temperature: 0_C3.2 - 3.6 V
sorFuel temperature: 20_C2.3 - 2.7 V
Fuel temperature: 40_C1.4 - 1.8 V
Fuel temperature: 80_C0.4 - 0.8 V
88Boost air temperature
sensorIgnition switch: ONIntake air temperature:
0_C3.2 - 3.8 V
Intake air temperature:
20_C2.3 - 2.9 V
Intake air temperature:
40_C1.5 - 2.1 V
Intake air temperature:
80_C0.4 - 1.0 V
89Engine speed sensorEngine: Idling1.5 - 2.5 V
91Neutral switchIgnition switch: ON
(Engine stops)Set the selector lever to P
or N0-1V
Set the selector lever to D,
2, L, or RSystem voltage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

I
N JE C TIO N NO ZZLE
R EM OVA L AND IN STA LLA TIO N 3
1
±1
N
×m
1
4 1
3
±2
N
×m
2 1
±2
N
×m
(E ngin e oil)
(
E ngin e oil)
7 1
1 2
2
±4
N
×m 4
4
±8
N
×m
R em oval ste p s
1 . E ngin e oil le ve l gauge and guid e
2 . A /T oil le ve l gauge and guid e
3 . C la m p
4 . In je ctio n pip e sta y
A A"
"
CA
5. In je ctio n pip e
" CA
6. In je ctio n pip e se al
" BA
7. Fuel re tu rn hose
8 . Fuel re tu rn pip e 9
. Fuel re tu rn pip e gaske t
D Rocke r co ve r
( R efe r to GRO UP 11 C -Cam sh aft.)
1 0. Fuel le ak off pip e
1 1 . Fuel le ak off pip e gaske t
A B"
12. In je ctio n nozzle asse m bly
" AA
13. N ozzle gaske t
" AA
14. In je ctio n nozzle
w
ww.W ork sh opM an uals .c o .u k
P urc h ased f r o m w ww.W ork sh opM an uals .c o .u k

I
N JE C TIO N PU M P
R EM OVA L AND IN STA LLA TIO N 5
.0
±1
.0 N
×m 5
.0
±1
.0 N
×m (
E ngin e oil) 1
2
5 8
1 3
3
6 14
1
5
R em oval ste p s
1 . In je ctio n pum p co nnecto r
2 . E ngin e sp eed se nso r co nnecto r
3 . E ngin e sp eed se nso r 1 co nnecto r
4 . E ngin e sp eed se nso r 1
5 . E ngin e sp eed se nso r 2 co nnecto r
6 . E ngin e sp eed se nso r 2
" CA
7. Fuel re tu rn hose
" BA
8. Fuel re tu rn hose "
BA
9. Fuel m ain hose
1 0. In je ctio n pum p sta y
1 1 . In je ctio n pum p co ve r asse m bly
1 2. In su la to r co lla r
1 3. In su la to r
1 4. In je ctio n pum p co ve r
A A"
"
AA
15. In je ctio n pum p asse m bly
w
ww.W ork sh opM an uals .c o .u k
P urc h ased f r o m w ww.W ork sh opM an uals .c o .u k

13C-1
DIESEL FUEL
<4M4>
CONTENTS
GENERAL 2.................................
Outline of Changes 2...........................
SERVICE SPECIFICATIONS 2.................
TROUBLESHOOTING 2.......................ON-VEHICLE SERVICE 12....................
Throttle Body Assembly Check 12................
INJECTION PUMP 13.........................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

DIESEL FUEL <4M4> -General/Service Specifications/Troubleshooting13C-2
GENERAL
OUTLINE OF CHANGES
Some service procedures have been established as the following changes have been made due to the
compliance with the Emission Regulation StepIII.
DThe intake manifold cover and injection pump cover have been reshaped.
DThe throttle body assembly has been changed.
DThe EGR valve assembly has been changed.
SERVICE SPECIFICATIONS
ItemStandard value
Throttle body assembly resistanceΩat - 10 - 50_C12 - 20
at 50 - 100_C12 - 23
TROUBLESHOOTING
FAIL-SAFE, BACKUP FUNCTIONS
When abnormalities in the major sensors are detected by diagnosis functions, pre-set control logic operates
to maintain a safe driving condition for the vehicle.
Diagnosis itemControl features in malfunction
Accelerator pedal position sensorDAccelerator pedal released (idle switch ON)
Acceleration opening degree = 0 %
DAccelerator pedal applied (idle switch OFF)
Engine controlled at low speed
Acceleration opening degree = 40 % , 28 %
DVoid cruise control
Idle switchDVoid idling speed control
DVoid cruise control
Engine speed sensorDEngine controlled at low speed
DVoid cruise control
Boost air temperature sensorMaintain the intake air temperature at 50_C
Vehicle speed sensorDVoid idling speed control
DVoid cruise control
DWith accelerator pedal released (when idle switch is on)
Accelerator opening angle = 0 %
DWith accelerator pedal depressed (when idle switch is off)
Accelerator opening angle = Fixed at 40 % (M/T), 28 % (A/T)
Engine coolant temperature sensorMaintain the engine coolant temperature at 80_C (engine running), 0_C
(engine stopped or just started)
Control sleeve position sensorDWith accelerator pedal released (when idle switch is on)
Engine speed = 800 r/min
DWith accelerator pedal depressed (when idle switch is off)
Engine speed = 2,000 r/min
DVoid cruise control
Timer piston position sensorDOpen control by means of engine speed
DVoid cruise control
Barometric pressure sensor (ECU built-in)Keep the barometric pressure at 101 kPa


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk