2000 LEXUS GS400 engine

I04038
I04039
BE±42
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
2343 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)8 ± Ground
Headlight dimmer switch HIGH beam or FLASHContinuity
1 ± GroundIgnition switch LOCK or ACCNo voltage
1 ± GroundIgnition switch ON or STARTBattery positive voltage
5 ± GroundEngine StopNo voltage
5 ± GroundEngine RunningBattery positive voltage
7 ± GroundConstantBattery positive voltage
9 ± GroundConstantBattery positive voltage
If circuit is specified, try replacing the relay with a new one.
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
16. INSPECT AUTOMATIC LIGHT CONTROL
AUTO ON:
(a) Turn the ignition switch ON.
(b) Turn the light control switch to AUTO.
(c) Gradually cover the top of the sensor.
(d) Check the accessory lights and the headlights should turn
ON.
17. INSPECT AUTOMATIC LIGHT CONTROL
AUTO OFF:
(a) Gradually expose the sensor.
(b) Check the headlights and the accessory lights should turn
OFF.
18. INSPECT LIGHT±OFF CONDITION
(a) Turn the ignition switch ON.
(b) Gradually cover the top of the sensor.
Lights auto ON:
(c) Check that the lights go off under the following conditions.
(1) Light control switch is OFF.
(2) The area surrounding the sensor gets bright.
(3) The driver's door is opened with the ignition switch
OFF.

I07728
20.9 mm (0.823 in.)
0.4°
3 m (9.84 ft)
W
V Center
Line
V LH Line V RH Line
H
HRH Line3 cm
(0.57°)LH
Line
W
I04297
Beam Angle Gauge
(Vertical Alignment)
Acceptable
Range
Bubble
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE±47
2348 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(c) Check the headlight aimming.
(1) Prepare the thick white colored paper.
(2) Stand the paper perpendicularly and ensure the
distance from it to the head lights is 9.84 ft.
(3) Ensure that the center line of vehicle and the paper
are at a 90 degree angle as shown in the illustration.
(H line)
(4) Engine running.
(5) Draw a horizontal line on the paper where the head
lights of the vehicle are to be.
(6) Draw a vertical line on the paper where the center
line of the vehicle is to be. (V center line)
(7) Take an appropriate measure to avoid affecting the
other light. (V RH and LH lines)
NOTICE:

Disconnect the connector of the other light to avoid
heat affection from the light because the outer lens of
the head light assembly is made of synthetic resin.
When connecting the connector again take care not
to wake the aiming out of adjustment.

When covering the headlight, finish it within 3 min-
utes.
(8) Turn the head lights ON.
(9) Check that the head lights light up the paper as
shown in the illustration.
(10) When the paper is not lighted up properly, adjust the
lights in the vertical or horizontal direction.
HINT:
As shown in the illustration, adjust aiming of the LH and RH
lights along each vertical line respectively.
(d) Vertical Alignment:
Adjust the headlight aimming.
(1) Using adjustment bolt A, adjust the headlight aim-
ing to within the specifiactions.
(2) Make sure the gauge bubble is within the accept-
able range.
HINT:
If the gauge bubble is outside the acceptable range, check that
the vehicle is parked on a level spot.
Readjust the headlight aiming after parking the vehicle on a lev-
el spot.

BE01R±06
I01351
Headlight Beam Level Control Actuator
Height Control SensorHeadlight Beam Level Control ECU
Driver Side Junction Block

ECU±IG Fuse

GAUGE Fuse
± BODY ELECTRICALHEADLIGHT BEAM LEVEL CONTROL SYSTEM
BE±49
2350 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
HEADLIGHT BEAM LEVEL CONTROL SYSTEM
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE0H2±08
I01352
Front Fog Lights
Combination Switch

Front Fog Light Switch Driver Side Junction Block

FOG Fuse

Fog Light Relay

Body ECU No.2
BE±52
± BODY ELECTRICALFOG LIGHT SYSTEM
2353 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
FOG LIGHT SYSTEM
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE0H0±06
I01353
Turn Signal LightsEngine Room No.1
Junction Block

TURN HAZ Fuse
Ignition Switch
Combination Switch

Turn Signal Switch
Hazard Warning Switch
Turn Signal Lights Turn Signal Lights
Driver Side Junction Block

GAUGE FuseCowl Side No.5
Junction Block

Turn Signal Flaher
± BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
BE±55
2356 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE023±07
I01357
Headlight Cleaner Relay Washer Tank

Headlight Cleaner Motor
Headlight Cleaner Switch
Headlight Cleaner Nozzle
Engine Room No.1
Junction Block

H±LP CLN H±Fuse
Ignition Switch
Driver Side Junction Block

WASHER Fuse
BE±72
± BODY ELECTRICALHEADLIGHT CLEANER SYSTEM
2373 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
HEADLIGHT CLEANER SYSTEM
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE0HN±07
I01358
Wiper Motor
Washer Tank

Washer Motor
Combination Switch

Wiper and Washer Switch
Driver Side Junction Block

WIPER Fuse

WASHER Fuse
Ignition Switch
BE±76
± BODY ELECTRICALWIPER AND WASHER SYSTEM
2377 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
WIPER AND WASHER SYSTEM
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE0HH±07
I01359
Brake Master Cylinder

Brake Fluid Level
Warning Switch
Combination Meter
and Telltale Light
Assembly
Airbag Sensor Assembly Parking Brake Switch
Driver Side
Junction Block

GAUGE Fuse

SRS±B FuseIgnition Switch
ECM
Washer Tank

Washer Level
Warning Switch Engine Room No.1
Junction Block

MPX±B Fuse
Seat Belt Buckle Switch
Rheostat Light Control
ABS, TRAC and VSC ECU
Clock Assembly

Passenger Seat Belt
Waning Light
BE±80
± BODY ELECTRICALCOMBINATION METER
2381 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
COMBINATION METER
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.