2000 LEXUS GS400 lights

BE0GW±08
I01355
Ignition Switch
Driver Side Junction Block

GAUGE Fuse
Back±up Lights
Park/Neutral Position Switch
± BODY ELECTRICALBACK±UP LIGHT SYSTEM
BE±67
2368 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BACK±UP LIGHT SYSTEM
LOCATION

BE0H6±08
I01356
Stop Light Switch
Driver Side Junction Block

STOP Fuse
Light Failure Sensor
Stop Lights
± BODY ELECTRICALSTOP LIGHT SYSTEM
BE±69
2370 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
STOP LIGHT SYSTEM
LOCATION

I04250

Combination Meter Wiring Circuit ± 1
:Speedometer
:Tachometer
:Fuel Receiver Gauge
:Engine Coolant
Temperature
Receiver Gauge
Speed Control Unit
CLOCK
to GAUGE Fuse
to MPX±B Fuse
to SRS Fuse
Tilt and Telescopic ECU
Body ECU NO.2ECM (GS400)
Ignitor (GS300)
Fuel Main Sender GaugeGround
Fuel Sub Sender Gauge
Light Control Rheostat
Illuminations
ABS, TRAC and VSC ECU
ABS, TRAC and VSC ECU Speed Signal Passenger seat
belt warning
Rr LIGHTS
SEAT BELT
OIL PRESS
OIL LEVEL
DOOR IG+
SRS +BA/T P
A/T R
A/T N
A/T D
A/T 4
A/T 3
A/T 2
A/T L
CRUISE MPX+BIG+IG+
5V
+B
to ECUto
PANEL
Fuse B4
B5
B6
B9
A5
A17A3A8 B16
LCDECU S
T
F
E
Power Source
Brake
Buzzer A11A2 A1 A6
B1
B13
B14A4
B22 ECU
ECU
ECU
S
T
F
E
CHARGE
FUEL LVL
ECT PWR
ECT SNOW TAIL or HEAD
Ground IG+IG+ IG+ IG+
+B
± BODY ELECTRICALCOMBINATION METER
BE±83
2384 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04079
Connector ºCº Connector ºDº
Connector ºFº Connector ºEº
Connector ºGº
1 131 13
1 201 12
± BODY ELECTRICALCOMBINATION METER
BE±93
2394 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
2. INSPECT COMBINATION METER CIRCUIT PLATE
Warning light circuit plate:
(a) Remove meter cover.
(b) Disconnect connectors ºCº, ºDº, ºEº, ºFº and ºGº from the
meter circuit plate and inspect the connectors on the wire
harness side as shown in the table.
Tester connectionCheck indicator lightSpecified condition
D10 (+) ± D12 (±)Fuel level warning lightContinuity
D6 (+) ± D8 (±)Headlight indiactor light (USA)
Taillight indiactor light (CANADA)Continuity
D2 (+) ± D4 (±)Hi±beam indicator lightContinuity
C3 (+) ± C7 (±)Engine oil level warning lightContinuity
C3 (+) ± C5 (±)Malfunction indicator lightContinuity
E19 (±) ± E20 (+)Slip warning lightContinuity
E18 (±) ± E20 (+)TRAC OFF indicator lightContinuity
E17 (±) ± E20 (+)Window washer level warning lightContinuity
E16 (±) ± E20 (+)ABS warning lightContinuity
E15 (±) ± E20 (+)VSC OFF indicator lightContinuity
E14 (±) ± E20 (+)Brake warning lightContinuity
E13 (±) ± E20 (+)ECT SNOW indicator lightContinuity
E12 (±) ± E20 (+)Low oil pressure warning lightContinuity
E11 (±) ± E20 (+)ECT PWR indicator lightContinuity
E10 (±) ± E20 (+)Discharge warning lightContinuity
E9 (±) ± E20 (+)CRUISE MAIN indicator lightContinuity
E8 (±) ± E20 (+)Seat belt warning lightContinuity
E7 (±) ± E20 (+)Rear Lights warning lightContinuity
E6 (±) ± E20 (+)Headlight leveling indiactorContinuity
E4 (+) ± E5 (±)SRS warning lightContinuity
E3 (±) ± E4 (+)Open door warning lightContinuity
F4 (±) ± F12 (+)A/T shift indicator light (L)Continuity
F11 (±) ± F12 (+)A/T shift indicator light (2)Continuity
F10 (±) ± F12 (+)A/T shift indicator light (3)Continuity
F8 (±) ± F12 (+)A/T shift indicator light (P)Continuity

I04091
F
E1
2
1/2
I04094
A
D
C
B
I01277
Battery Ignition
SwitchWarning Light
Wire Harness Side
1 BE±98
± BODY ELECTRICALCOMBINATION METER
2399 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
13. INSPECT FUEL SUB SENDER GAUGE RESISTANCE
Measure the resistance between terminals 1 and 2 for each
float position.
Float position mm (in.)Resistance (W)
F: Approx. 9.5 (0.37) ± 3 (0.12)Approx. 2.0 ± 1.0
1/2: Approx. 110.5 (4.35) ± 3 (0.12)Approx. 33.0 ± 3.0
E: Approx. 206.5 (8.13) ± 3 (0.12)Approx. 61.3 ± 1.0
If resistance value is not as specified, replace the sub sender
gauge.
14. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION (See page DI±754)
15. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE RESISTANCE
Measure the resistance between terminals with fixing pointer to
the stopper.
Tester connectionResistance (W)
A ± B140 ± 185
C ± D130 ± 175
If resistance value is not as specified, replace the receiver
gauge.
HINT:
This circuit includes the diode.
If resistance value is not as specified, replace the receiver
gauge.
16. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, test the bulb.

I01278
I01279
Battery Ignition
SwitchWarning Light
I04095
OFF
ON
I04096
± BODY ELECTRICALCOMBINATION METER
BE±99
2400 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
17. INSPECT LOW OIL PRESSURE SWITCH CONTINUITY
(a) Disconnect the connector from the switch.
(b) Check that continuity exists between terminal and ground
with the engine stopped.
(c) Check that no continuity exists between terminal and
ground with the engine running.
HINT:
Oil pressure should be over 24.5 kPa (0.25 kgf/cm
2, 3.55 psi).
If operation is not as specified, replace the switch.
18. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connector from the brake fluid warning
switch.
(b) Release the parking brake pedal.
(c) Connect the terminals on the wire harness side of the lev-
el warning switch connector.
(d) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or wire har-
ness.
19. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
CONTINUITY
(a) Remove the reservoir tank cap and strainer.
(b) Disconnect the connector.
(c) Check that no continuity exists between the terminals with
the switch OFF (float up).
(d) Use siphon, etc. to take fluid out of the reservoir tank.
(e) Check that continuity exists between the terminals with
the switch ON (float down)
(f) Pour the fluid back in the reservoir tank.
If operation is not as specified, replace the switch.
20. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
CIRCUIT (See page DI±835)
21. INSPECT PARKING BRAKE SWITCH CONTINUITY
(a) Check that continuity exists between the terminal and
switch body with the switch ON (switch pin released).
(b) Check that no continuity exists between the terminal and
switch body with the switch OFF (switch pin pushed in).
If operation is not as specified, replace the switch or inspect
ground point.
22. INSPECT PARKING BRAKE SWITCH CIRCUIT
(See page DI±796)

I04097
Battery Ignition
SwitchWarning Light
Wire Harness Side
I04098
Wire Harness Side
I04099
BatteryIgnition
SwitchWarning Light
Wire Harness Side BE±100
± BODY ELECTRICALCOMBINATION METER
2401 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
23. INSPECT REAR LIGHTS WARNING LIGHT
(See page DI±841)
(a) Disconnect the connector from the light failure sensor and
ground terminal 3 on the wire harness side connector.
(b) Start the engine, check that the warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
24. INSPECT LIGHT FAILURE SENSOR CIRCUIT
Disconnect connector from the light failure sensor and inspect
the connectors on the wire harness side as follows.
Tester connectionConditionSpecified condition
1 ± GroundConstantContinuity *
2 ± GroundConstantContinuity *
6 ± GroundConstantContinuity *
7 ± GroundConstantContinuity *
11 ± GroundConstantContinuity
12 ± GroundConstantContinuity *
5 ± GroundLight control switch OFFNo voltage
5 ± GroundLight control switch in TAIL or HEADBattery positive voltage
8 ± GroundIgnition switch in LOCK or ACCNo voltage
8 ± GroundIgnition switch ONBattery positive voltage
9, 10 ± GroundStop light switch OFFNo voltage
9, 10 ± GroundStop light switch ONBattery positive voltage
*: There is resistance because this circuit is grounded through
the bulb.
If circuit is as specified, replace the relay.
If circuit is not as specified, wiring diagram and inspect the cir-
cuits connected to other parts.
25. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Run the engine.
(c) Turn the ignition switch ON, check that the warning light
lights up approximatery 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.

I04102
ON OFF
I04103
ON OFF
I04104
Wire Harness Side
I01286
BatteryWarning Light
± BODY ELECTRICALCOMBINATION METER
BE±101
2402 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
26. INSPECT ENGINE OIL LEVEL WARNING SENSOR
(a) Check that continuity exists between terminals with the
switch to below 40 °C (104 °F). (Warning switch ON)
(b) Heat the switch to above 60 °C (140 °F) in an oil bath.
(c) Check that there is continuity between terminals with the
switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
27. INSPECT ENGINE OIL LEVEL WARNING SENSOR
CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.
Tester connectionConditionSpecified condition
2 ± GroundConstantContinuity
If continuity is not as specified, inspect the wire harness or
ground point.
28. INSPECT OPEN DOOR WARNING LIGHT
Disconnect the connector from the door courtesy switch and
ground terminal 1 on the wire harness side, and check that the
warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
29. INSPECT DOOR COURTESY SWITCH CONTINUITY
AND CIRCUIT (See page BE±60)