2000 LEXUS GS400 sensor

D01005
Q03721
D01048
Q06925
AT±36
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (1UZ±FE)
1984 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(b) Turn the crankshaft to gain access to each bolt.
(c) Hold the crankshaft pulley nut with a wrench and remove
the 6 bolts.
Torque: 48 N´m (490 kgf´cm, 35 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
First install the black colored bolt and then the 5 other bolts.
12. SUPPORT TRANSMISSION WITH JACK
13. REMOVE 4 ENGINE REAR MOUNTING SET BOLTS
Torque: 26 N´m (270 kgf´cm, 20 ft´lbf)
14. DISCONNECT CONNECTORS AND WIRE HARNESS
(a) Tilt down the transmission.
NOTICE:
Take care so that the cooling fan does not come in contact
with the fan shroud.
(b) Disconnect the following connectors:
(1) O/D direct clutch speed sensor connector
(2) Vehicle speed sensor connector
(3) Park/neutral position switch connector
(4) Solenoid connector
(c) Disconnect the wire harness from the clamp on the trans-
mission.

AT05Y±01
D00910
Q07487
SST
AT0103
± AUTOMATIC TRANSMISSIONATF TEMPERATURE SENSOR
AT±5
1953 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
ATF TEMPERATURE SENSOR
ON±VEHICLE REPAIR
CAUTION:
When working with FIPG material, you must observe the follow-
ing items.

Using a razor blade and gasket scraper, remove all the old
FIPG material from the gasket surfaces.

Thoroughly clean all components to remove all the loose
material.

Clean both sealing surfaces with a non±residue solvent.

Apply FIPG in an approx. 1 mm (0.04 in.) wide bead along
the sealing surface.

Parts must be assembled within 10 minutes of application.
Otherwise, the FIPG material must be removed and reap-
plied.
1. REMOVE DRAIN PLUG WITH GASKET AND DRAIN
AT F
2. REMOVE OIL PAN
NOTICE:
Some fluid will remain in the oil pan.
(a) Remove the 19 bolts.
(b) Install the blade of SST between the transmission case
and oil pan, cut off applied sealer, and remove the oil pan.
SST 09032±00100
NOTICE:
When removing the oil pan, be careful not to damage the oil
pan flange.
3. EXAMINE PARTICLES IN PAN
Remove the magnets and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and
on the magnets to anticipate the type of wear you will find in the
transmission.
Steel (magnetic) ... bearing, gear and clutch plate wear
Brass (non±magnetic) ... bushing wear

D00752
D00753
D00909
D00916
D00909
AT±6
± AUTOMATIC TRANSMISSIONATF TEMPERATURE SENSOR
1954 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
4. REMOVE OIL STRAINER
NOTICE:
Be careful as some fluid will come out of the oil strainer.
(a) Remove the 4 bolts and oil strainer.
(b) Remove the 3 gaskets from the oil strainer.
5. REMOVE SOLENOID WIRING WITH ATF TEMPERA-
TURE SENSOR
(a) Disconnect the ATF temperature sensor.
(b) Remove the bolt and clamp.
(c) Disconnect the 7 connectors from the solenoid valves.
(d) Remove the bolt and pull out the solenoid connector.
6. INSTALL SOLENOID WIRING WITH ATF TEMPERA-
TURE SENSOR
(a) Install the solenoid connector with the bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Connect the 7 connectors to the solenoid valves.
(c) Install the clamp with the bolt.
Torque: 6.4 N´m (65 kgf´cm, 56 in.´lbf)
(d) Connect the ATF temperature sensor.

D00753
D00752
D00912
D01917
Seal Breadth 2 ~ 3 mm (0.08 ~ 0.12 in.)
D00910
ºAº
± AUTOMATIC TRANSMISSIONATF TEMPERATURE SENSOR
AT±7
1955 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. INSTALL OIL STRAINER
(a) Install 3 new gaskets.
(b) Install the oil strainer with the 4 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
8. INSTALL OIL PAN
(a) Install the 3 magnets in the indications of the oil pan.
(b) Remove any packing material and be careful not to drop
oil on the contacting surfaces of the transmission case
and oil pan.
(c) Apply FIPG to the oil pan.
FIPG:
Part No. 08826 ± 00090, THREE BOND 1281 or
equivalent
(d) Install the oil pan with the 19 bolts.
Torque: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
HINT:
Replace the only ºAº bolt with a new one.
9. INSTALL DRAIN PLUG WITH NEW GASKET
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
10. FILL FLUID AND CHECK FLUID
(See page DI±318)

AT05Z±01
D00754
D01741
Spring Check Ball Body AT±8
± AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
1956 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
VALVE BODY ASSEMBLY
ON±VEHICLE REPAIR
CAUTION:
When working with FIPG material, you must observe the follow-
ing items.

Using a razor blade and gasket scraper, remove all the old
FIPG material from the gasket surfaces.

Thoroughly clean all components to remove all the loose
material.

Clean both sealing surfaces with a non±residue solvent.

Apply FIPG in an approx. 1 mm (0.04 in.) wide bead along
the sealing surface.

Parts must be assembled within 10 minutes of application.
Otherwise, the FIPG material must be removed and reap-
plied.
1. REMOVE DRAIN PLUG WITH GASKET AND DRAIN
AT F
2. REMOVE OIL PAN (See page AT±5)
3. EXAMINE PARTICLES IN PAN (See page AT±5)
4. REMOVE OIL STRAINER (See page AT±5)
5. REMOVE SOLENOID WIRING WITH ATF TEMPERA-
TURE SENSOR (See page AT±5)
6. REMOVE VALVE BODY
Remove the 21 bolts and valve body.
7. REMOVE CHECK BALL BODY AND SPRING
NOTICE:
Do not drop the check ball body and spring.

D00754
A
CB
B
B
B
C
CA
DB
AT±10
± AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
1958 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(b) Install the 21 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
Bolt length:
Bolt A: 23 mm (0.91 in.)
Bolt B: 28 mm (1.10 in.)
Bolt C: 36 mm (1.42 in.)
Bolt D: 55 mm (2.17 in.)
12. INSTALL SOLENOID WIRING WITH ATF TEMPERA-
TURE SENSOR (See page AT±5)
13. INSTALL OIL STRAINER (See page AT±5)
14. INSTALL OIL PAN (See page AT±5)
15. INSTALL DRAIN PLUG WITH NEW GASKET
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
16. FILL FLUID AND CHECK FLUID (See page DI±318)

BE02C±02
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE±111
2412 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
POWER WINDOW CONTROL SYSTEM
TROUBLESHOOTING
1. WINDOW DOES NOT OPERATE WITH POWER WINDOW MASTER SWITCH. (MANUAL OR AU-
TOMATIC OPERATION CAN NOT BE PERFORMED.)
TroubleSuspect Area (terminal No.)Parts name
All windows do not operate with master
switch of each window.
PWS terminal of body ECU does not output sig-
nal.

Body ECU PWS terminal (B8) output

Master Switch PW terminal (15) output

Check wire harness between PWS terminal
and PW terminal (15)

Body ECU

Master switch
Windows except driver's do not operate
with master switch of each window.
Master switch (window lock circuit) faulty

Check continuity between master switch PW
terminal (15) and W/L2 terminal (10)

Check wire harness between W/L2 terminal of
master switch (10) and PCT terminals of each
power window switch.

Master switch
Only specific window does not operate.
(Manual and automatic operation can not
be performed.)
FLOW CHART ±
Only specific window does not operate.
(Automatic operation can not be per-
formed.)When ºJam Protectionº sensor is defective, auto-
matic function as a fail±safe function might be
unable.
Master switch

Power window switch

Door control ECU

BE±114
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
2415 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) Only AUTO DOWN operation does not
operate.
(All window (Except driver side) doors.)
Master switch ON SC3 terminal does not output.
Driver door control ECU SC3 terminal does not
input.

Master switch SC3 terminal (13)

Driver door control ECU SC3 terminal (B11)

Check wire harness between terminal SC3 (13)
and SC3 (B11)

Driver door control ECU

Master switch
Only AUTO DOWN operation does not
operate.
(Only specific window does not operate.)Master switch faulty

Check continuity of master switch.
3. THE KEY RELATED POWER WINDOW OPERATION DOES NOT OPERATE WITH DRIVER SIDE
DOOR KEY CYLINDER. (MASTER SWITCH OPERATION IS NORMAL.)
TroubleSuspect Area (terminal No.)Parts name
Door lock system does not operate with
door key.Refer to ºPOWER DOOR LOCK CONTROL
SYSTEMº.±
Door lock system does not operate with
door key.
Fail±safe mode caused by error on jam protec-
tion sensor of power window.
(Operation of power window with multi±function
transmitter is prohibited.)
HINT: DTC 31 ± 38 output
Refer to ºMultiplex Communication Systemº.
4. POWER WINDOW DOES NOT OPERATE WITH MULTI±FUNCTION TRANSMITTER. (WINDOWS
OPERATE NORMALLY WITH MASTER SWITCH.)
TroubleSuspect Area (terminal No.)Parts name
Door lock and luggage compartment
opener do not operate with multi±function
transmitter.Refer to ºWIRELESS DOOR LOCK CONTROL
SYSTEMº.±
Only luggage compartment opener oper-
ates with multi±function transmitter.Wireless door lock transmitter faulty.Check wireless door lock transmitter.
Door lock and luggage compartment
opener operate with multi±function trans-
mitter.
Fail±safe mode caused by error on jam protec-
tion sensor of power window.
(Operation of power window with multi±function
transmitter is prohibited.)
HINT: DTC 31 ± 38 output
Refer to ºMultiplex Communication Systemº.
5. WINDOW MOVES DOWN WITHOUT BEING ORDERED DURING THE UP OPERATION
TroubleSuspect Area (terminal No.)Parts name
After the window is fully closed, it starts to
move down.
Power window motor limit switch wire harness
faulty.

Power window motor reset switch is reset.

Driver door control ECU LMT terminal (B12)

Driver door control ECU
The window moves down during the up
operation.FLOW CHART ±