2000 LEXUS GS400 light

BE0GN±01
BE±152
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2453 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
PRE±CHECK
Make the vehicle in the initialized condition:
The initialized condition is the condition when the following conditions are satisfied.
(1) Key plate has not been inserted in the ignition key cylinder.
(2) All the doors are closed. (Door warning light is OFF.)
(3) All the doors are locked.
(4) Wireless door lock control switch (Buzzer switch) is ON.
Under the standard operation, when repeating UNLOCK and LOCK switch 3 times or more alternately, check the
UNLOCK±LOCK operation from 3rd time onward.

Following procedures are standard operation.
(1) Keep about 1 M away to the right direction from the outside handle of a driver's seat.
(2) Face the transmitter toward the vehicle and press one of transmitter switches for about 1 sec.


As of the security function, even the wireless function is normal, there may be the case that only UNLOCK opera-
tion will not work.

As of the body customize function, if ºoperation twiceº has been set using LEXUS hand±held tester, only driver's
seat is unlocked by unlock operation performed once.
Normal


Operative distance may differ according to
an operator, the way of holding the transmitter
or position.

Because weak electric wave is used, when
there is strong wave or noise in the used
frequency ,operation distance might be
shortened.
No Yes
Only wireless function (Remote control) will not operate.
(If a new transmitter or a transmitter of the same type that works properly with the vehicle is not available.)
Check when pressing UNLOCK switch
and LOCK switch under standard
operation, that the transmitter LED
lights up once more.
NoYe s
Basic function check:
Transmitter LED inspection:

BE0GO±04
I04149
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±157
2458 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control transmitter battery replace-
mentº on page BE±161.
(a) Using a screwdriver, remove the screw and cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (±) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, face the key plate of
the transmitter to the vehicle, and check the transmitter
operation when pressing transmission switch on the side
of the transmitter body.
Standard:

Remote control of vehicle door lock can be operated.

LED lights up more than once.
HINT:

The minimum operation distance differs according to op-
erator, the way of holding the transmitter, and location.

As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
(e) Install the battery (lithium battery).
(f) Install a cover so that O±ring is not distorted or slipped off.
(g) Using a screwdriver, tighten the screw.

I04026

Engine Room No.1 Junction Block
Fuses Relays
1. MAIN H±Fuse
2. FL ABS NO.1 H±Fuse
3. ALT H±Fuse
4. ABS NO.2 H±Fuse
5. H±LP CLN H±Fuse
6. RAD NO.1 Fuse
7. ALT±S Fuse
8. EFI Fuse
9. TURN HAZ Fuse
10. TEL Fuse
11. AM2 Fuse
13. HORN Fuse 12. ETCS Fuse
14. MPX±B Fuse
15. ECU±B1 Fuse
16. HTR FuseB. Starter Relay A. Headlight Control Relay
C. EFI Relay
17. FAN MAIN H±Fuse
18. CDS FAN H±Fuse
20. H±LP R LWR Fuse 19. RAD FAN H±Fuse
21. H±LP L LWR Fuse
22. H±LP R UPR Fuse
23. H±LP L UPR Fuse1
2 3 4 5 6 7 8 9 10 11 12 13
14 15
16 18 17 19
20 21 22 23 A
BC
± BODY ELECTRICALPOWER SOURCE
BE±17
2318 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04028

Engine Room No.3 Relay Block
Relays
A. FAN NO.1 Relay
B. FAN NO.2 Relay
C. A/C COMP Relay
D. FAN NO.3 Relay

Engine Room No.2 Relay Block
Relays
A. Horn Relay
B. ABS SOL Relay
C. TRC MTR Relay
D. ABS MTR Relay
I04027
I04028
A
B
C
D
EE. Headlight Dimmer
(Daytime Running Light No.2) Relay
A
B
C
DFuses
1. H±LP R UPR Fuse
(w/ Daytime Running Light System)
2 H±LP L UPR Fuse
(w/ Daytime Running Light System) 12 BE±18
± BODY ELECTRICALPOWER SOURCE
2319 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04029
Fuses
Relays 1. AM1 H±Fuse
2. WASHER Fuse
3. FOG Fuse
4. TAIL Fuse
B. Taillight Control Relay A. Fog Light Relay
C. Body ECU No.2
Driver Side Instrument Panel Junction Block
5. SRS±ACC Fuse
6. GAUGE Fuse
7. FUEL OPN Fuse
8. D FR DOOR Fuse
9. PANEL Fuse
10. HTR Fuse
11. SRS±B Fuse
12. P/SEAT (D) Fuse
13. RAD NO.2 Fuse
14. WIP Fuse
15. OBD Fuse
16. STOP Fuse
17. CIG Fuse
18. ECU±IG Fuse
19. STARTER Fuse
20. IGN Fuse
21. D FR DOOR Fuse
2
21 34 5
678 9
10 11 12 13
14 15 16 17
18 19 20AB
C 1
± BODY ELECTRICALPOWER SOURCE
BE±19
2320 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

BE0HD±04
I05186
ºBrightº ºDarkº1
2
3
4
Black coloured tape
I04048
Wire Harnes Side BE±182
± BODY ELECTRICALELECTRO CHROMIC MIRROR SYSTEM
2483 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT ELECTRO CHROMIC INNER MIRROR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 4.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 2 and the negative (±) lead to terminal 3.
(c) Attach a black coloured tape to forward sensor to prevent
it from sensing.
(d) When the mode is turned to AUTO, check that indicator
light lights up.
(e) Light up the mirror with an electric light, and check that
there is battery positive voltage and mirror surface
changes ºbrightº to ºdarkº.
If operation is not as specified, replace the inner mirror.
2. INSPECT ELECTRO CHROMIC INNER MIRROR CIR-
CUIT
Disconnect the connector from the mirror and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
4 ± GroundConstantContinuity
1 ± GroundIgnition switch LOCK or ACCNo voltage
1 ± GroundIgnition switch ONBattery positive voltage
If circuit is not as specified, inspect the circuits connected to
other parts.

BE0GI±07
I04180e±6±2±H
I04181
4 6
L
R Switch
L Switch
I04182
Seat back connector ºAº
Seat cushion
inner
connector ºBº
± BODY ELECTRICALSEAT HEATER SYSTEM
BE±185
2486 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT SEAT HEATER SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Right side3 ± 4 ± 6Continuity
OFF±No continuity
Left side2 ± 4 ± 6Continuity
Illumination circuit1 ± 5Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SEAT HEATER INDICATOR LIGHT OPERA-
TION
(a) Connect the positive (+) lead from the battery to terminal
6 and the negative (±) lead to terminal 4.
(b) Push the seat heater switch Right or Left side and check
that the indicator light lights up.
If operation is not as specified, replace the switch and inspect
the circuits connected to other parts.
3. INSPECT SEAT HEATER CUSHION CONTINUITY
(a) Heat the thermostat with a light.
(b) Inspect the seat heater cushion continuity between termi-
nals, as shown.
Tester connectionConditionSpecified condition
A2 ± B1ConstantContinuity
A1 ± A2Seat heater temperature below 25 °C (77 °F)Continuity
B1 ± B2Seat heater temperature above 45 °C (113 °F)No continuity
If continuity is not as specified, replace the seat cushion pad.

27 Noise NOISE PRODUCED BY VIBRATION OR SHOCK WHILE DRIVING
No
Ye s Is speaker properly installed?
Noise is produced from static eletricity accumulating in the vehicle body. With vehicles stationary lightly tap each system.
Is noise produced?Install properly.
Each system faulty. Is speaker properly installed?
No
No Ye s
Ye s
28 Noise NOISE PRODUCED WHEN ENGINE STARTS
NoYe s Whistling noise which becomes high±pitched when
accelerator strongly depressed, disappears shortly
after engine stops.Generator noise.
A/C noise.
Fuel gauge noise.
Horn noise.
Ignition noise.
Turn signal noise.
Washer noise.
Engine coolant temp. gauge noise.
Wiper noise. Whining noise occurs when A/C is operating.
Scratching noise occurs during sudden acceleration, driving on rough
roads or when ignition switch is turned ON.
Clicking sound is heard when horn button is pressed, then
released. Whirring/grating sound is heard when pushed
continuously.
Murmuring sound stops when engine stops.
Tick±tack noise occurs in co±ordination with blinking
offlasher.
Noise occurs during window washer operation.
Scratching noise occurs while engine is running,
and continues a while even after engine stops.
Scraping noise in line with wiper beat.
Other type of noiseYe s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s No
No
No
No
No
No
No
No
± BODY ELECTRICALAUDIO SYSTEM
BE±215
2516 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)