2000 LEXUS GS400 wheel alignment

SA0RL±01
SA±28
± SUSPENSION AND AXLEFRONT UPPER SUSPENSION ARM
2028 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±26).
AFTER INSTALLATION, CHECK ABS SPEED SENSOR (See page DI±389) AND FRONT WHEEL
ALIGNMENT (See page SA±4)

SA0RO±01
± SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
SA±33
2033 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±30).
AFTER INSTALLATION, CHECK ABS SPEED SENSOR SIGNAL (See page DI±389) AND FRONT
WHEEL ALIGNMENT (See page SA±4)

SA0RT±01
SA±38
± SUSPENSION AND AXLEFRONT LOWER BALL JOINT
2038 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±36).
AFTER INSTALLATION, CHECK FRONT WHEEL ALIGNMENT (See page SA±4)

F02399
FRONT
REARSA0R3±01
Z03382
SA3213
A
DB
C Front
SA±4
± SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
2004 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
FRONT WHEEL ALIGNMENT
INSPECTION
1. MEASURE VEHICLE HEIGHT
Tire sizeFront*1 mm (in.)Rear*2 mm (in.)
P215/60R16 94V245 (9.63)226 (8.90)
225/55R16 94V240 (9.45)221 (8.70)
235/45ZR17238 (9.37)219 (8.62)
*1: Front measuring point
Measure from the ground to the center of the lower suspension
arm mounting bolt.
*
2: Rear measuring point
Measure from the ground to the center of the No.2 lower sus-
pension arm mounting bolt.
NOTICE:
Before inspecting the wheel alignment, adjust the vehicle
height to the specification.
If the vehicle height is not within the specification, try to adjust
it by pushing down on or lifting the body.
2. INSTALL CAMBER±CASTER±KINGPIN GAUGE
ONTO WHEEL ALIGNMENT TESTER
Follow the specific instructions of the equipment manufacturer.
3. INSPECT CAMBER, CASTER AND STEERING AXIS
INCLINATION
Camber
Left±right error±0°16' ± 30' (±0.27° ± 0.5°)
30' (0.5°) or less
Caster
Left±right error7°33' ± 30' (7.55° ± 0.5°)
30' (0.5°) or less
Steering axis inclination
Left±right error8°52' ± 30' (8.87°± 0.5°)
30' (0.5°) or less
If the camber is not within the specification, adjust it by adjusting
cam.
4. INSPECT TOE±IN
Toe±in
(total)A + B: 0°09' ± 12' (0.15° ± 0.2°)
C ± D: 1.5 ± 2 mm (0.06 ± 0.08 in.)
If the toe±in is not within the specification, adjust it at the tie rod
end.

F02400
SA1204
± SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
SA±5
2005 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. ADJUST CAMBER
HINT:

After adjusting the camber, inspect the caster and toe±in.

Try adjusting the camber to the center value of the specifi-
cation.
(a) Loosen the camber adjusting cam nut of the lower sus-
pension arm.
(b) Turn the camber adjusting cam of the lower suspension
arm and adjust camber.
HINT:
Camber changes about 5' (0.08°) with each graduation of the
adjusting cam.
(c) Torque the camber adjusting cam nut of lower suspension
arm.
Torque: 172 N´m (1,755 kgf´cm, 127 ft´lbf)
6. ADJUST TOE±IN
(a) Remove the boot clips.
(b) Loosen the tie rod end lock nuts.
(c) Turn the left and right rack ends an equal amount to adjust
the toe±in.
HINT:

Try to adjust the toe±in to the center value.

Make sure that the lengths of the left and right rack ends
are same.
Rack end length difference: 1.5 mm (0.059 in.) or less
(d) Torque the tie rod end lock nuts.
Torque: 56 N´m (570 kgf´cm, 41 ft´lbf)
(e) Place the boot on the seat and clamp it.
HINT:
Make sure that the boots are not twisted.

SA0028
Front
A: Inside
B: Outside A
A
BB
SA±6
± SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
2006 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. INSPECT WHEEL ANGLE
Turn the steering wheel fully, and measure the turning angle.
Inside wheel38°51' (36°51' ± 39°51')
38.85° (36.85° ± 39.85°)
Outside wheel (Reference)32°05'
32.08°
If the wheel angles differ from the standard of the specification,
inspect the toe±in.

SA0R4±01
SA3213
D AB
C Front
F03479
A
B
F02401
± SUSPENSION AND AXLEREAR WHEEL ALIGNMENT
SA±7
2007 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REAR WHEEL ALIGNMENT
INSPECTION
1. MEASURE VEHICLE HEIGHT (See page SA±4)
2. INSTALL CAMBER±CASTER±KINGPIN GAUGE
ONTO WHEEL ALIGNMENT TESTER
Follow the specific instructions of the equipment manufacturer.
3. INSPECT CAMBER
Camber
Left±right error±0°47' ± 30' (±0.78° ± 0.5°)
30' (0.5°) or less
4. INSPECT TOE±IN
Toe±in
(total)A + B: 0°08' ± 12' (0.13° ± 0.2°)
C ± D: 1.4 ± 2 mm (0.056 ± 0.08 in.)
5. ADJUST CAMBER AND TOE±IN
(a) Measure the lengths of the toe control link and No.2 lower
suspension arm, as shown in the illustration.
Length: A ± B = 4.0 mm (0.16 in.) or less
If they are not within the specifications, adjust the lengths of
them by turning the adjusting cam, as shown, until (A ± B) is less
than 4.0 mm (0.16 in.).
(b) Measure the camber and toe±in.
(c) Adjust the camber.
(1) Loosen the camber adjusting cam nut of lower sus-
pension arm No.2.
(2) Turn the camber adjusting cam of lower suspension
arm No.2 and adjust camber.
HINT:
Camber changes about 5.0' (0.08°) with each graduation of the
cam.
(3) Torque the camber adjusting cam nut.
Torque: 110 N´m (1,120 kgf´cm, 81 ft´lbf)

F02402
SA±8
± SUSPENSION AND AXLEREAR WHEEL ALIGNMENT
2008 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(d) Adjust the toe±in.
(1) Loosen the camber adjusting cam nut of toe control
link.
(2) Turn the camber adjusting cam of toe control link
and adjust toe±in.
HINT:
Camber changes about 5.0' (0.08°) with each graduation of the
cam.
(3) Torque the camber adjusting cam nut.
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)