2000 LEXUS GS400 Throttle

± ENGINE MECHANICAL (2JZ±GE)VALVE CLEARANCE
EM±9
1363 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
15. REINSTALL SPARK PLUGS
16. REINSTALL IGNITION COILS AND HIGH±TENSION
CORD SET ASSEMBLY (See page IG±9)
17. REINSTALL NO.3 TIMING BELT COVER
(a) Install the gasket to the timing belt cover.
(b) Using a 5 mm hexagon wrench, install the timing belt cov-
er with the 4 bolts.
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)
(c) Install the oil filler cap.
18. REINSTALL THROTTLE BODY AND INTAKE AIR CON-
NECTOR ASSEMBLY
(a) Install a new gasket to the air intake chamber.
(b) Place the throttle body together with the intake air con-
nector on the cylinder head.
(c) Connect the vacuum hose (from actuator for ACIS) to the
No.1 vacuum pipe.
(d) Connect the 2 water bypass hoses to the throttle body.
(e) Install the 4 bolts and 2 nuts holding the intake air connec-
tor to the air intake chamber.
Torque: 28 N´m (280 kgf´cm, 21 ft´lbf)
(f) Install the 2 nuts holding the throttle body bracket to the
cylinder head.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(g) Connect the air assist hose to the intake air connector.
(h) Install the PCV hose to the intake air connector.
(i) Install the EVAP hose (from charcoal canister) to the VSV
for EVAP.
(j) Install the vacuum hose (from No.2 vacuum pipe) to the
No.1 vacuum pipe.
(k) Install the throttle position sensor connector.
(l) Install the accelerator pedal position sensor connector.
(m) Install the throttle control motor connector.
(n) Install the VSV connector for EVAP.
(o) Secure the engine wire with the clamp on the throttle body
bracket.
(p) Install the engine wire clamp with the clamp bracket of the
throttle body.
(q) Connect the accelerator cable to the throttle body.
19. REINSTALL INTAKE AIR RESONATOR
20. REINSTALL ENGINE COVER
Install the engine cover with the 4 nuts.
21. REFILL WITH ENGINE COOLANT
22. START ENGINE AND CHECK FOR LEAKS

A02735
A09752
A11121
Case Clamp
New Clamp
A02819
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
EM±57
1411 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
15. INSTALL VACUUM CONTROL VALVE SET AND NO.2
VACUUM PIPE
(a) Install the vacuum control valve set and No.2 vacuum
pipe with the 3 nuts.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(b) Install the engine wire clamp to the clamp bracket of the
No.2 vacuum pipe.
(c) Connect the VSV connector for the ACIS.
16. INSTALL AIR INTAKE CHAMBER (See page SF±49)
17. INSTALL OIL DIPSTICK AND GUIDE FOR A/T
(See page EM±68)
18. INSTALL OIL DIPSTICK AND GUIDE FOR ENGINE
(See page LU±12)
19. INSTALL THROTTLE BODY AND INTAKE AIR
CONNECTOR ASSEMBLY (See page EM±5)
20. INSTALL WATER BYPASS OUTLET AND NO.1 WATER
BYPASS PIPE (See page CO±13)
21. INSTALL EXHAUST MANIFOLD
(a) Install 2 new gaskets to the cylinder head.
(b) Using a 14 mm deep socket wrench, install the exhaust
manifold with the 8 nuts. Uniformly tighten the nuts in sev-
eral passes.
Torque: 40 N´m (408 kgf´cm, 30 ft´lbf)
(c) Connect the 3 heated oxygen sensor connectors and
clamp.
(d) Install a new clamp and the case clamp as shown in the
illustration.
22. CONNECT FRONT EXHAUST PIPE TO EXHAUST
MANIFOLD
(a) Temporarily install the pipe support bracket to the trans-
mission with the 2 bolts.
(b) Install 2 new gaskets to front end of the front exhaust pipe,
and connect the front exhaust pipe to the exhaust man-
ifold with the 3 bolts and nuts.
Torque: 44 N´m (440 kgf´cm, 32 ft´lbf)
(c) Tighten the 2 bolts holding the pipe support bracket to the
transmission.

EM0DH±05
A02753
EVAP
Hose
Clamp
MAF Meter
Connector
A02751
EM±62
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
1416 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE HOOD
NOTICE:
Be careful not to damage the body or glass with the hood
end.
2. REMOVE ENGINE UNDER COVER
3. DRAIN ENGINE COOLANT
4. DRAIN ENGINE OIL
5. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
6. REMOVE AIR CLEANER INLET
7. REMOVE AIR CLEANER, MAF METER AND INTAKE
AIR RESONATOR ASSEMBLY
(a) Disconnect the MAF meter connector.
(b) Disconnect the engine wire clamp from the air cleaner
case.
(c) Disconnect the EVAP hose from the air cleaner case.
(d) Disconnect the PS air hose from the No.4 timing belt cov-
er.
(e) Disconnect the PCV hose from the No.2 cylinder head
cover.
(f) Loosen the hose clamp bolt holding the intake air resona-
tor to the throttle body.
(g) Remove the 3 bolts, the air cleaner, MAF meter and intake
air resonator assembly.
8. DISCONNECT ACCELERATOR CABLE FROM EN-
GINE
9. REMOVE RADIATOR ASSEMBLY (See page CO±18)
10. REMOVE DRIVE BELT (See page CH±1)
11. REMOVE FRONT SUSPENSION MEMBER BRACE
Remove the 6 bolts and brace.

A02765
EVAP Hose
A02751
A02753
EVAP
Hose Clamp
MAF Meter
Connector
EM±72
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
1426 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(g) Connect the heated oxygen sensor (bank 1 sensor 1)
connector.
(h) Connect the heated oxygen sensor (bank 1 sensor 2)
connector.
(i) Connect the EVAP hose to the pipe (from charcoal canis-
ter).
(j) Connect the heater hose to the heater pipe.
(k) Connect the heater hose to the water bypass pipe.
(l) Connect the ground strap to the dash panel.
(m) Connect the fuel inlet hose to the fuel pipe support.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
(n) Connect the starter wire to the terminal and manifold stay.
(o) Connect the ground wire to the floor.
16. INSTALL FRONT SUSPENSION MEMBER BRACE
Install the brace with the 6 bolts.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
17. INSTALL DRIVE BELT (See page CH±1)
18. INSTALL RADIATOR ASSEMBLY (See page CO±23)
19. CONNECT ACCELERATOR CABLE TO ENGINE
20. INSTALL AIR CLEANER, MAF METER AND INTAKE
AIR CONNECTOR PIPE ASSEMBLY
(a) Connect the intake air resonator to the throttle body.
(b) Install the air cleaner case with the 3 bolts.
(c) Tighten the hose clamp bolt holding the intake air resona-
tor to the throttle body.
(d) Connect the MAF meter connector.
(e) Connect the engine wire clamp to the air cleaner case.
(f) Connect the EVAP hose to the air cleaner case.
(g) Connect the PS air hose to the No.4 timing belt cover.
(h) Connect the PCV hose to the No.2 cylinder head cover.
21. INSTALL AIR CLEANER INLET
22. INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.
23. FILL WITH ENGINE COOLANT
24. FILL WITH ENGINE OIL
25. START ENGINE AND CHECK FOR LEAKS
26. INSTALL ENGINE UNDER COVER

DTC No.
Indicates the diagnostic trouble code.

Page or Instructions
Indicates the page where the inspection procedure
for each circuit is to be found, or gives instructions
for checking and repairs.

Detection Item
Indicates the system of the problem or
contents of the problem.
Trouble Area
Indicates the suspect area of the
problem.
Mass Air Flow Circuit MalfunctionDetection Item

Open or short in mass air flow meter circuit

Mass air flow meter

ECM DTC No.
(See page)Trouble AreaMIL* MemoryP0100
(DI±24)
P0101
(DI±28)
P0115
(DI±33)
Open or short in intake air temp. sensor
circuit

Intake air temp. sensor

ECM Intake Air Temp. Circuit
Malfunction P0110
(DI±29)

Open or short in engine coolant temp. sensor circuit

Engine coolant temp. sensor

ECM
Throttle/ Pedal Position Sensor/Switch
ºAº Circuit MalfunctionEngine Coolant Temp.
Circuit Malfunction

Open or short in throttle position sensor circuit

Throttle position sensor

ECM
DTC CHART (SAE Controlled)
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument or other
factors.
If a malfunction code is displayed during the DTC check mode, check the circuit for that code listed in the table
below. For details of each code, turn to the page referred to under the ºSee pageº for the respective ºDTC No.º
in the DTC chart.
Mass Air Flow Circuit
Range/ Performance Problem
Mass air flow meter

Throttle position sensor Throttle/ Pedal Position Sensor/ Switch
ºAº Circuit Range / Performance Prob-
lem P0116
(DI±37)Engine Coolant Temp.
Circuit Range/ Performance Problem
Engine coolant temp. sensor

Cooling system
± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN±27
27 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
4. DIAGNOSTIC TROUBLE CODE CHART
The inspection procedure is shown in the table below. This table permits efficient and accurate troubleshoot-
ing using the diagnostic trouble codes displayed in the diagnostic trouble code check. Proceed with trouble-
shooting in accordance with the inspection procedure given in the diagnostic chart corresponding to the
diagnostic trouble codes displayed. The engine diagnostic trouble code chart is shown below as an example.

± INTRODUCTIONTERMS
IN±37
37 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) CW
Curb Weight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro±Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR±VMEgr±Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E±VRVElectric Vacuum Regulating Valve
EXHExhaust
FEFuel Economy
FFFront±Engine Front±Wheel±Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront±Engine Rear±Wheel±Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront±Wheel±Drive
GASGasoline
GNDGround
HACHigh Altitude Compensator
H/BHatchback

± INTRODUCTIONTERMS
IN±39
39 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) OEM
Original Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead Valve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take±Off
R & PRack And Pinion
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight±Hand
RHDRight±Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear±Engine Rear±Wheel Drive
RRSRigid Rear Suspension
RWDRear±Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold±Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
TCTurbocharger
TCCSTOYOTA Computer±Controlled System
TCVTiming Control Valve
TDCTop Dead Center

IN0D6±01
± INTRODUCTIONTERMS
IN±41
41 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
GLOSSARY OF SAE AND LEXUS TERMS
This glossary lists all SAE±J1930 terms and abbreviations used in this manual in compliance with SAE rec-
ommendations, as well as their LEXUS equivalents.
SAE
ABBREVIATIONSSAE TERMSLEXUS TERMS
( )±±ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal±
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection±
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position±
CTOXContinuous Trap Oxidizer±
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition±
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode±
ECLEngine Control Level±
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control±
FEEPROMFlash Electrically Erasable Programmable Read Only
Memory±
FEPROMFlash Erasable Programmable Read Only Memory±
FFFlexible Fuel±
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)