2000 Lexus ES300 radio

AUDIO
244
20E205
Push this button on the upper side to step up the
station band or on the lower side to step down.
Your radio automatically changes to stereo reception
when a stereo broadcast is received. ªSTº appears on
the display. If the signal becomes weak, the radio
reduces the amount of channel separation to prevent the
weak signal from creating noise. If the signal becomes
extremely weak, the radio switches from stereo to mono
reception. In this case, ªSTº disappears from the
display. (b) Presetting a station

AUDIO
245
20E206
1. Tune in the desired station.
2. Push one of the station selector buttons ( 1±6 )
and hold it until a beep is heard. This sets the station
to the button and the button number ( 1±6 ) appears
on the display.
Each button can store one AM station and two FM
stations. To change the preset station to a different one,
follow the same procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown
fuse. (c) Selecting a station
Your Lexus has an electronic tuning radio (ETR). Tune
in the desired station using one of the following methods.

AUDIO
246
20E139
Preset tuning: Push the button ( 1±6 ) for the station you
want briefly. The button number ( 1±6 ) and station
frequency appear on the display.
Manual tuning: Push the ªTUNE SEEKº button briefly.
Each time you push the button, the radio will step up or
down to another frequency.
Seek tuning: Push the ªTUNE SEEKº button and hold
it until you hear a beep. The radio will begin seeking up
or down for a station of the nearest frequency and will
stop on reception. Each time you push the button, the
stations will be searched out one after another.

AUDIO
247
20E125
To scan all the frequencies: Push the ªSCANº button.
ªSCANº appears on the display. The radio will find the
next station up the band, stay there for a few seconds,
and then scan again. To select a station, push the
ªSCANº button a second time.
To scan the preset stations: Push the ªP.SCANº
button. ªP.SCANº appears on the display. The radio will
tune in the next preset station up the band, stay there for
a few seconds, and then move to the next preset station.
To select a station, push the ªP.SCANº button a second
time.Cassette tape player operation
(a) Playing a cassette tape
20E173

AUDIO
264
Car audio system operating hints
NOTICE
To ensure the correct audio system operation:
Be careful not to spill beverages over the audiosystem.
Do not put anything other than a cassette tapeor CD magazine into the cassette tape slot or
CD changer.
The use of cellular phone inside or near thevehicle may cause a noise from the speakers of
the audio system which you are listening to. However, this does not indicate a malfunction.
Radio reception
Usually, the problem with radio reception does not mean
there is a problem with your radio ± it is just the normal
result of conditions outside the vehicle.
For example, nearby buildings and terrain can interfere
with FM reception. Power lines or telephone wires can
interfere with AM signals. And of course, radio signals
have a limited range. The farther you are from a station,
the weaker its signal will be. In addition, reception
conditions change constantly as your vehicle moves.
Here are some common reception problems that
probably do not indicate a problem with your radio:
FM
Fading and drifting stations ± Generally, the effective
range of FM is about 40 km (25 miles). Once outside this
range, you may notice fading and drifting, which
increase with the distance from the radio transmitter.
They are often accompanied by distortion.
Multi±path ± FM signals are reflective, making it
possible for two signals to reach your antenna at the
same time. If this happens, the signals will cancel each
other out, causing a momentary flutter or loss of
reception.
Static and fluttering ± These occur when signals are
blocked by buildings, trees, or other large objects.
Increasing the bass level may reduce static and
fluttering.

AUDIO
265
Station
swapping ± If the FM signal you are listening to
is interrupted or weakened, and there is another strong
station nearby on the FM band, your radio may tune in
the second station until the original signal can be picked
up again.
AM
Fading ± AM broadcasts are reflected by the upper
atmosphere ± especially at night. These reflected
signals can interfere with those received directly from
the radio station, causing the radio station to sound
alternately strong and weak.
Station interference ± When a reflected signal and a
signal received directly from a radio station are very
nearly the same frequency, they can interfere with each
other, making it difficult to hear the broadcast.
Static ± AM is easily affected by external sources of
electrical noise, such as high tension power lines,
lightening, or electrical motors. This results in static.
Caring for your cassette player and tapes
For the best performance for your cassette player and
tapes:
Clean the tape head and other parts regularly.
 A dirty tape head or tape path can decrease sound
quality and tangle your cassette tapes. The easiest
way to clean them is by using a cleaning tape. (A wet
type is recommended.) Use high±quality cassettes:

Low±quality cassette tapes can cause many
problems, including poor sound, inconsistent playing
speed, and constant auto±reversing. They can also
get stuck or tangled in the cassette player.
 Do not use a cassette if it has been damaged or
tangled or if its label is peeling off.
 Do not leave a cassette in the player if you are not
listening to it, especially if it is hot outside.
 Store cassettes in their cases and out of direct
sunlight.
 Avoid using cassettes with a total playing time longer
than 100 minutes (50 minutes per side). The tape
used in these cassette is thin and could get stuck or
tangled in the cassette player.

STARTING AND DRIVING
278ªSTARTº ± Starter motor on. The key will return to
the ªONº position when released.
For starting tips, see page 281.
ªONº ± Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the ªONº position if the
engine is not running. The battery will dischargeand the electronic ignition system/distributorignition system could be damaged.
ªACCº ± Accessories such as the radio operate, but
the engine is off.
If you leave the key in the ªACCº or ªLOCKº position and
open the driver's door, a buzzer will remind you to
remove the key.

ELECTRICAL COMPONENTS
440
No.FUSEAMPERECIRCUIT
1 ABS60Anti±lock brake system
2 INJ20No circuit
3 DRL NO.25Daytime Running Light System
4H±LP15*1Left±hand headlight (low beam)4 HLPLH(LWR)10*2
5H±LP15*1Right±hand headlight (lowbeam)5 HLPRH(LWR)10*2beam)
6 ALT100Charging system
7 T±STK30No circuit
8 HTR50Air conditioning system, Seat
heater
9 MAIN40Headlight, Starting system
10 DOME7.5
Theft deterrent system, Clock,
Door courtesy light, Interior
light, Ignition switch light, Vanity
light, Wireless remote control
system
11 ECU±B10Air conditioning system,
Power seat system
12 RADIO
NO.120Audio system
13 HAZARD15Emergency flashers, Turn
signal lights