2000 GMC YUKON Seats

1-12
If more cargo space is
desired, the third seat can
also be folded and tumbled
forward or removed if
necessary by pulling up on
the release lever labeled 2.
The seat locks into place and does not need to be removed
when carrying cargo. See ªRemoving the Third Row Seats º
for Utility later in this section for removal instructions.
Suburban/Yukon XL: The seatback of the third seat
(if equipped) in Suburban/Yukon XL models also folds
down to create more cargo space.
To fold the seatback down, pull up on the release lever,
labeled 1, located on the rear of the seatback, then push
the seatback forward.To return the seat to the passenger position, pull up on
the release lever and then pull up on the seatback until
it locks into the upright position. Push forward on the
seatback to make sure it is locked into position.
If still more cargo space is desired, the third seat can
also be folded and tumbled forward by using the lever,
labeled 2. To return the seats to their original position,
reverse the above steps.
Fold and Tilt Feature (Suburban/Yukon XL
Third Seat)
Once the third seatback has been folded down, the
entire seat can be tilted forward to create a flat load
floor. To do this, you will need to enter the rear cargo
area of the vehicle. Make sure the head restraints have
been lowered completely.
With the seat folded, unlatch the seat from the floor by
pulling up on the lever located under the carrying handle
at the rear of the seat labeled 2. Lift the rear of the seat
up, off of the floor. You will not be able to unlatch the
seat from the floor unless the seatback is folded down.
Tilt the seat fully forward and secure it in place using
the support rod located on the underside of the seat,
passenger side. Make sure the support rod pin is fully
engaged in the lock.

1-13
Push and pull on the seat, making sure that the support
rod is holding it firmly in place. Use the seat in this
position only when necessary for additional cargo space.
CAUTION:
If the support rod isn't properly engaged, the
folded third row seat could come loose in a
sudden stop or crash. That could cause injury to
people and damage to your vehicle. Always be
sure the support rod is properly engaged when
the third row seat is folded forward.
To return the seat to its seating position, push forward
on the seat and release the support lock rod. Secure the
support rod in its stored position on the underside of the
seat. Lower the seat to the floor and let the seat drop into
place. Lift up on the carrying handle to make sure the
seat is locked in place.
Return the seatback to the upright position by pulling
up on the release lever labeled 1 before the back can be
folded upright. Pull the seatback forward to make sure it
is locked into place.Removing the Third Row Seats
Utility: If your vehicle has third row seating, it can be
taken out for more cargo space.
To remove the seat, fully open the rear doors and enter
the rear of the vehicle.
Fold the seatback forward
into the seat cushion by
using the lever labeled 1.
The seat cannot be
removed unless the
seatback is folded.

1-14
To unlatch the seat from the
back of the floor, pull up on
the release lever labeled 2
at the rear of the seat and
lift the rear of the seat up
from the floor.
Pull on the release lever located in the lower middle to
unlatch the seat from the front of the floor and pull the
seat out. Use one hand on the release lever and the other
on the handle to pull the seat out.
Suburban/Yukon XL: If your vehicle has third row
seating, it can be taken out for more cargo space.
To remove the seat, fully open the rear doors and enter
the rear of the vehicle.Fold the seatback forward into the seat cushion by using
the lever labeled 1. The seat cannot be removed unless
the seatback is folded.
To unlatch the seat from the floor, pull up on the release
lever labeled 2 at the rear of the seat and lift the rear of
the seat up, off of the floor.
Pull on the strap at the rear of the seat to release the
front seat latches. Then, pull the seat straight back,
towards the rear of the vehicle and remove it. There are
wheels at the front of the seat to assist you.
Replacing the Rear Seat (Third Row Seats)
Utility: To put the seat back in, place the front of
the seat on the load floor facing towards the front of
the vehicle. Slide the wheels into the slots on the floor
and lock into place using the hooks there. Once the
latches are engaged pull on lever 3 to let the seat drop
into place. Release the lever labeled 1 to return the seat
to its upright position. Push and pull on the seat to make
sure it is locked into place.

1-16
CAUTION:
It is extremely dangerous to ride in a cargo
area, inside or outside of a vehicle. In a collision,
people riding in these areas are more likely to
be seriously injured or killed. Do not allow people
to ride in any area of your vehicle that is not
equipped with seats and safety belts. Be sure
everyone in your vehicle is in a seat and using a
safety belt properly.
Your vehicle has a light
that comes on as a reminder
to buckle up. (See ªSafety
Belt Reminder Lightº in
the Index.)In most states and Canadian provinces, the law says to
wear safety belts. Here's why: They work.
You never know if you'll be in a crash. If you do have
a crash, you don't know if it will be a bad one.
A few crashes are mild, and some crashes can be so
serious that even buckled up a person wouldn't survive.
But most crashes are in between. In many of them,
people who buckle up can survive and sometimes
walk away. Without belts they could have been badly
hurt or killed.
After more than 30 years of safety belts in vehicles,
the facts are clear. In most crashes buckling up does
matter ... a lot!

1-21
How to Wear Safety Belts Properly
Adults
This part is only for people of adult size.
Be aware that there are special things to know about
safety belts and children. And there are different
rules for smaller children and babies. If a child will be
riding in your vehicle, see the part of this manual called
ªChildren.º Follow those rules for everyone's protection.
First, you'll want to know which restraint systems your
vehicle has.
We'll start with the driver position.
Driver Position
This part describes the driver's restraint system.
Lap-Shoulder Belt
The driver has a lap-shoulder belt. Here's how to
wear it properly.
1. Close and lock the door.
2. Adjust the seat (to see how, see ªSeatsº in the Index)
so you can sit up straight.
3. Pick up the latch plate and pull the belt across you.
Don't let it get twisted.
The shoulder belt may lock if you pull the belt across
you very quickly. If this happens, let the belt go back
slightly to unlock it. Then pull the belt across you
more slowly.
4. Push the latch plate into the buckle until it clicks.

1-37
Q:What if I add a snow plow? Will it keep the
air bags from working properly?
A:We've designed our air bag systems to work
properly under a wide range of conditions,
including snow plowing with vehicles equipped
with the optional Snow Plow Prep Package
(RPO VYU). But don't change or defeat the
snow plow's ªtripping mechanism.º If you do,
it can damage your snow plow and your vehicle,
and it may cause an air bag inflation.
Center Passenger Position
Lap Belt
If your vehicle has front and rear bench seats, someone
can sit in the center positions.
When you sit in a center seating position, you have a
lap safety belt, which has no retractor. To make the belt
longer, tilt the latch plate and pull it along the belt.

1-48
A rear-facing infant restraint (B) positions an infant
to face the rear of the vehicle. Rear
-facing infant
restraints are designed for infants of up to about
20 lbs. (9 kg) and about one year of age. This type
of restraint faces the rear so that the infant's head,
neck and body can have the support they need in
a frontal crash. Some infant seats come in two
parts
-- the base stays secured in the vehicle and
the seat part is removable.

1-50
A booster seat (F) is designed for children who
are about 40 to 60 lbs., or even up to 80 lbs.
(18 to 27 kg, or even up to 36 kg), and about
four to eight years of age. A booster seat is
designed to improve the fit of the vehicle's safety
belt system. Booster seats with shields use lap
-only
belts; however, booster seats without shields use
lap
-shoulder belts. Booster seats can also help
a child to see out the window.When choosing a child restraint, be sure the child
restraint is designed to be used in a vehicle. If it is,
it will have a label saying that it meets federal motor
vehicle safety standards.
Then follow the instructions for the restraint. You may
find these instructions on the restraint itself or in a
booklet, or both. These restraints use the belt system
in your vehicle, but the child also has to be secured
within the restraint to help reduce the chance of personal
injury. The instructions that come with the infant or
child restraint will show you how to do that. Both the
owner's manual and the child restraint instructions are
important, so if either one of these is not available,
obtain a replacement copy from the manufacturer.