2000 FORD MUSTANG turn signal bulb

WARNING LIGHTS AND CHIMES
Base instrument cluster
Optional instrument cluster
Turn signal
Illuminates when the
left or right turn signal
or the hazard lights are
turned on. If one or
both of the indicators stay on continuously or flash
faster, check for a burned-out turn signal bulb. Refer
toExterior bulbsin theMaintenance and care
chapter.
High beams
Illuminates when the
high beam headlamps
are turned on.
Safety belt
Momentarily illuminates
when the ignition is
turned to the ON
P! BRAKE
L
0
00000 00
C
E
FH
LH
10 203020 406080100
120
140
160
180
405060 70
80
90
100
11 0
1204
5
6
7 3
2
1
H
THEFT
RPMX1000
FUEL DOORSELECT/RESET
LOW
FUELO/D
OFF AIR
BAGSERVICE
ENGINE
SOON
MPH km/h
ABS
.
P! BRAKE
L
0
00000 00
C
E
FH
LH
102040608020 40608010 012 0 14 0
160
180
200
220
240
100
120
140
305070 90
110
13 0
1504
5
6
7
8 3
2
1
H
THEFT
RPMX1000
FUEL DOORSELECT/RESET
LOW
FUELO/D
OFF AIR
BAGSERVICE
ENGINE
SOON
MPH km/h
ABS
.
Instrumentation
8

²Turn signals
²Backup lamps
²License plate lamp
Do not remove lamp bulbs unless they will be
replaced immediately. If a bulb is removed for an
extended period of time, contaminants may enter
the lamp housings and affect performance.
Replacing headlamp bulbs
To remove the headlamp bulb:
1. Make sure headlamp switch is in OFF position,
then open the hood.
2. At the back of the
headlamp, pull two
retainer pins up to
release the headlamp
assembly.
3. Pull headlamp
assembly forward
disengaging the lamp
from the rear hidden snap retainers to expose the
back of the bulb.
4. Disconnect the
electrical connector
from the bulb by
pulling rearward.
5. Remove the bulb
retaining ring by
rotating it
counterclockwise
(when viewed from the
rear) to free it from
the bulb socket, and slide the ring off the plastic
base. Keep the ring to retain the new bulb.
Maintenance and care
178

6. Without turning,
remove the old bulb
from the lamp
assembly by gently
pulling it straight out of
the lamp assembly.
To install the new bulb:
Handle a halogen headlamp bulb carefully
and keep out of children's reach. Grasp the
bulb only by its plastic base and do not touch the
glass. The oil from your hand could cause the bulb
to break the next time the headlamps are
operated.
1. With the flat side of the new bulb's plastic base
facing upward, insert the glass end of the bulb into
the lamp assembly. You may need to turn the bulb
left or right to align the grooves in the plastic base
with the tabs in the lamp assembly. When the
grooves are aligned, push the bulb into the lamp
assembly until the plastic base contacts the rear of
the lamp assembly.
2. Install the bulb retaining ring over the plastic base
until it contacts the rear of the socket by rotating
clockwise until you feel a ªstop.º
3. Connect the electrical connector into the plastic
base until it snaps, locking it into position.
4. Install the headlamp on vehicle by aligning the
lamp with the rear snap retainers, push to seat and
secure with two retainer pins.
5. Turn the headlamps on and make sure they work
properly. If the headlamp was correctly aligned
before you changed the bulb, you should not need to
align it again.
Replacing front parking lamp/turn signal bulbs
1. Make sure the headlamp control is in the OFF
position.
Maintenance and care
179

GAWR (Gross Axle
Weight Rating) ........ 109
definition ............... 109
driving with
a heavy load .......... 109
location .................. 109
GVWR (Gross Vehicle
Weight Rating) ........ 109
calculating ............. 109
definition ............... 109
driving with
a heavy load .......... 109
location .................. 109
Hazard flashers ....... 117
Head restraints ......... 62
Headlamps ................. 18
aiming .................... 183
bulb
specifications ........ 182
daytime
running lights .......... 18
flash to pass ............ 41
high beam ............ 8,18
replacing bulbs ..... 178
turning on and off .. 18
warning chime ........ 13
Heating ...................... 20
heating and air
conditioning
system ..................... 20
Hood ........................ 135
Ignition ..................... 194
positions of the
ignition .................... 41
removing the key .. 109
Infant seats (see
Safety seats) ........ 82,83
Inspection/maintenance
(I/M) testing ............ 177
Instrument panel
cleaning ................. 188
cluster ................. 8,188lighting up panel
and interior ............. 19
location of
components ............... 8
Jump-starting
your vehicle ............. 128
Keys
key in
ignition chime ......... 13
positions of the
ignition .................... 41
removing from
the ignition ............ 109
Lamps
bulb replacement
specifications
chart ...................... 182
cargo lamps ............. 19
daytime
running light ........... 18
fog lamps ................. 48
headlamps ........ 18,178
headlamps,
flash to pass ............ 41
instrument panel,
dimming ................... 19
interior
lamps ......... 45,181,182
replacing bulbs ..... 177
178,179,180,181
Lane change indicator
(see Turn signal) ...... 40
Lights, warning and
indicator ...................... 8
air bag ........................ 9
anti-lock
brakes (ABS) ..... 12,96
anti-theft ................... 9
brake ........................ 12
charging system ........ 9
check coolant .......... 12
high beam ................. 8
Index
215