2000 FORD MUSTANG hood release

OPENING THE HOOD
1. Inside the vehicle,
pull the hood release
handle located under
the bottom left corner
of the instrument
panel.
2. Go to the front of the vehicle and release the
auxiliary latch that is located under the front center
of the hood.
3. Lift the hood and secure it with the prop rod.
HOOD
Maintenance and care
135

²Turn signals
²Backup lamps
²License plate lamp
Do not remove lamp bulbs unless they will be
replaced immediately. If a bulb is removed for an
extended period of time, contaminants may enter
the lamp housings and affect performance.
Replacing headlamp bulbs
To remove the headlamp bulb:
1. Make sure headlamp switch is in OFF position,
then open the hood.
2. At the back of the
headlamp, pull two
retainer pins up to
release the headlamp
assembly.
3. Pull headlamp
assembly forward
disengaging the lamp
from the rear hidden snap retainers to expose the
back of the bulb.
4. Disconnect the
electrical connector
from the bulb by
pulling rearward.
5. Remove the bulb
retaining ring by
rotating it
counterclockwise
(when viewed from the
rear) to free it from
the bulb socket, and slide the ring off the plastic
base. Keep the ring to retain the new bulb.
Maintenance and care
178

2. Open the hood.
3. At the back of the
headlamp, pull two
retainer pins up to
release the headlamp
assembly.
4. Pull headlamp
assembly forward
disengaging the lamp
from the rear snap retainers to expose the back of
the bulb.
5. Rotate the bulb
socket
counterclockwise and
remove from lamp
assembly.
6. Carefully pull the
bulb straight out from
the socket and push in
the new bulb.
7. To complete installation, follow the removal
procedure in reverse order.
Replacing high-mount brakelamp bulbs
1. Open trunk.
2. Inside trunk, locate
access hole under the
rear decklid.
3. Remove the bulb
socket by rotating it 45
degrees and pulling it
out of the lamp
assembly.
4. Carefully pull bulb
straight out of socket and push in new bulb.
5. To complete installation, follow the removal
procedure in reverse order.
Maintenance and care
180

Item Information
Required fuel Unleaded fuel only - 87 octane
Fuel tank capacity 59.4L (15.7 gallons)
Engine oil capacity
(includes filter
change)4.7L (5.0 quarts). Use Motorcraft SAE
5W-30 Super Premium Motor Oil,
Ford specification WSS-M2C153-G
Tire size and
pressureSee label on inside of glove box door.
Hood release Pull handle under the left side of the
instrument panel.
Coolant
capacity-3.8L OHV
V6 engine
1
11.2L (11.8 quarts)
Coolant capacity-
4.6L SOHC V8
engine
1
13.3L (14.1 quarts)
Power steering fluid
capacityFill to line on reservoir or dipstick.
Use Motorcraft MERCONtAT F.
Manual transmission
fluid capacity-3.8L
OHV V6 engine
2
2.6L (5.6 pints). Use Motorcraft
MERCONtAT F.3
Manual transmission
fluid capacity-4.6L
SOHC V8 engine
2
3.1L (6.6 pints). Use Motorcraft
MERCONtAT F.3
Automatic
transmission fluid
capacity-3.8L OHV
V6 engine
2
13.1L (13.9 quarts). Use Motorcraft
MERCONtV ATF.4
Automatic
transmission fluid
capacity-4.6L SOHC
V8 engine
2
12.0L (12.8 quarts). Use Motorcraft
MERCONtV ATF.4
Windshield washer
fluid3.8L (4.0 quarts). Use Ultra-Clear
Windshield Washer Concentrate.
1Use Ford Premium Engine Coolant (green in color). DO NOT USE
Ford Extended Life Engine Coolant (orange in color). Refer to
Adding engine coolant, in the Maintenance and Care chapter.
2Ensure the correct automatic transmission fluid is used.
Transmission fluid requirements are indicated on the dipstick or on
the dipstick handle. MERCONtand MERCONtV are not
interchangeable. DO NOT mix MERCONtand MERCONtV. Refer to
your Scheduled Maintenance Guide to determine the correct service
interval.
Filling station information
223