2000 Citroen C5 ignition

Downloaded from www.Manualslib.com manuals search engine 196
RECOMMENDATIONS - PRECAUTIONS (AL 4 and 4 HP 20 AUTOMATIC GEARBOXES)
Engines : 6FZ - RFN - RHZ - XFX - 4HX
Towing
The front of the vehicle must be raised in order to be towed.
If the front of the vehicle cannot be raised :
IMPERATIVE : - Put gear lever in position «N».
- Do not add any oil.
AL4 gearbox
- Do not exceed 50 km/h (30mph) over a distance of 50 km (30 m).
4 HP 20 gearbox
- Do not exceed 70 km/h (45mph) over a distance of 100 km (60 m).
Driving.
Never drive with the ignition switched off.
Never push the vehicle to try to start it;
(impossible with an automatic gearbox).
Lubrication
The automatic gearbox is only lubricated when the engine is running.Removing - refitting. (Automatic gearbox).
WARNING : Never place the gearbox on its lower casing
(risk of deforming the tray and damaging the hydraulic valve block).
Never use the connections as handles for raising, turning, holding or
pushing the gearbox.
ESSENTIAL :
- Fit the converter retaining peg while the gearbox is removed.
- Fit the centring peg to locate the gearbox on the engine:
(remove the converter retaining peg just before locating)
WARNING :With the emergency programme selected, an impact is
felt when changing from ‘‘P’’‘‘R’’or ‘‘N’’‘‘R’’.
Precautions to be taken
CLUTCH
GEARBOX
DRIVESHAFTS

Downloaded from www.Manualslib.com manuals search engine 201
CLUTCH
GEARBOX
DRIVESHAFTS
RECOMMENDATIONS - PRECAUTIONS (4 HP 20 AUTOMATIC GEARBOX)
Engines : XFX - 4HX
SHIFT LOCK
The shift lockis a system which locks the gear selection lever in the park position"P".
Unlocking the «shift lock» (normal operation).
Switch on the ignition.
Apply the brake pedal and keep it pressed.
Using the selection lever, disengage from position «P».
Unlocking the «shift lock»(with a fault).
NOTE :It is impossible to unlock the «shift lock»with the «normal operation»method.
The causes of the fault may arise from the following components :
- «Shift lock».
- Gear lever position switch.
- Automatic gearbox ECU.
- Electrical harnesses.
- Battery voltage.
Remove :
- The gear lever knob(1)by pulling upwards.
- The cover (2)(unclip).
- The shutter.
Unlock the «shift lock» (4)using a screwdriver.
Using the selection lever, disengage from position «P».
C5FPOCUDC5FPOCTC

Downloaded from www.Manualslib.com manuals search engine 202
CLUTCH
GEARBOX
DRIVESHAFTS
4 HP 20 GEARBOX CONTROLS
Engines : XFX - 4HX
Selection control.
The gear selection control has 5 positions.
The selection lever is guided by the shape of the stepped gate and by a retaining spring which holds it
towards the left.
The gear selection control is equipped with the «shift lock», so you have to switch on the ignition and
apply the brake pedal to unlock the selection lever from the park position.
Selection (P): Park(locking and immobilisation of the vehicle).
Selection (R): Reverse gear.
Selection (N) : Neutral.
Selection (D): Drive (Use of the four gears in their autoadaptive automatic function).
Selection (M) : Manual (M + M -)allowing the driver to select gears by pulling and pushing the gear lever.
In position M, selection is by an electronic sensor located close to the gear lever.
The variation of flux necessary to the movement of the sensor cells is obtained by a magnet located on
the lever itself. This enables the change of status.
B2CP3DKD