2000 CHRYSLER VOYAGER service reset

to non-emission codes, they will seem like an intermit-
tent. These codes require a set of parameters to be
performed (The DRBIIItpre-test screens will help
with this for MONITOR codes), this is called a ªTRIPº.
All EURO STAGE III OBD DTCs will be set after one
or in some cases two trip failures, and the MIL will be
turned on. These codes require three successful (no
failures) TRIPS to extinguish the MIL, followed by 40
warm-up cycles to erase the code.
3.3.2 INTERMITTENT CODE
A diagnostic trouble code that is not there every
time the PCM checks the circuit is an ªintermittentº
code. Most intermittent codes are caused by wiring
or connector problems. Defects that come and go
like this are the most difficult to diagnose; they
must be looked for under specific conditions that
cause them. The following checks may assist you in
identifying a possible intermittent problem:
²Visually inspect related wire harness connectors.
Look for broken, bent, pushed out, or corroded
terminals.
²Visually inspect the related harnesses. Look for
chafed, pierced, or partially broken wire.
²Refer to any Hotline Newsletters or technical
service bulletins that may apply.
²Use the DRBIIItdata recorder or co-pilot.
²Use the DRBIIItPEP module lab scope.
3.3.3 RESET COUNTER
The reset counter counts the number of times the
vehicle has been started since codes were last set,
erased, or the battery was disconnected. The reset
counter will count up to 255 start counts.
The number of starts helps determine when the
trouble code actually happened. This is recorded by
the PCM and can be viewed on the DRBIIItas
STARTS since set.
When there are no trouble codes stored in mem-
ory, the DRBIIItwill display ªNO DTC'S Detectedº
and the reset counter will show ªSTARTS since
clear = XXX.º
3.3.4 HANDLING NO TROUBLE CODE
PROBLEMS
Symptom checks cannot be used properly unless
the driveability problem characteristic actually
happens while the vehicle is being tested.
Select the symptom that most accurately de-
scribes the vehicle's driveability problem and then
perform the test routine that pertains to this symp-
tom. Perform each routine test in sequence until the
problem is found. For definitions, see Section 6.0
Glossary of Terms.SYMPTOM DIAGNOSTIC TEST
HARD START CHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING ENGINE VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
START AND
STALLCHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
8
GENERAL INFORMATION
ProCarManuals.com

Symptom:
P-0125 CLOSED LOOP TEMP NOT REACHED
When Monitored and Set Condition:
P-0125 CLOSED LOOP TEMP NOT REACHED
When Monitored: After engine is started, for ten minutes.
Set Condition: The engine temperature does not go above 10 degrees C (50 degrees F) by
13 minutes after the engine is started for 2 consecutive trips.
POSSIBLE CAUSES
PCM CONNECTOR AND TERM DAM, PSHD OUT, OR MISWIRED
ECT SENSOR CONN AND TERM DAM, PSHD OUT, MISWIRED
ECT SENSOR RESISTANCE >=11.00 K OHMS
PCM DEFECTIVE
THERMOSTAT DEFECTIVE
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRB, read the FREEZE FRAME DATA.
Using the FREEZE FRAME DATA, attempt to duplicate the condition that has set
this fault.
Note that the DTC is a 2 trip failure.
Does P0121 reset?All
Ye s®Go To 3
No®Go To 2
2 The conditions required to set the DTC are no longer present.
Ensure the engine cooling system is operating properly, coolant level is at specifica-
tion, and no external or internal coolant leaks. Refer to the appropriate service
category for cooling system information.
Is the Cooling System operating correctly?All
Ye s®Test complete
No®Repair as necessary.
Perform Powertrain verification Test VER-5A
3 Ignition off.
Disconnect the ECT Sensor Connector.
Note: Check Connectors - clean/repair as necessary.
Is any Terminal damaged, pushed out, or miswired?All
Ye s®Clean or repair connector as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 4
51
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition off.
Remove the Throttle Body per service information procedure.
Note: Clean Throttle Body in a well ventilated area and wear rubber gloves.
While holding the Throttle open spray entire Throttle Body Bore with Mopar parts
cleaner.
Using a soft scuff pad, clean the Throttle Body Bore and Throttle Plate.
Using compressed air, dry the Throttle Body and install Throttle Body on Manifold.
Reconnect IAC Motor Connector and reset the IAC Motor Steps with the DRB.
Start engine and let idle.
With the DRB, actuate the minimum air flow.
Is the idle RPM within the range shown in the chart? Refer to the Service
Information.All
Ye s®Test Complete.
No®Replace the Throttle Body.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Start engine, allow engine idle to stabilize for 60 seconds.
With the DRB, read target idle and engine RPM.
Is the engine RPM within +200/-100 RPM of target idle?All
Ye s®Go To 5
No®Go To 8
5 Ignition Off
Remove the IAC Motor from the housing.
Turn Ignition on with Engine Not Running.
With the DRB, actuate the IAC Stepper Motor.
Wiggle the Wiring Harness from the IAC Motor to the PCM.
Did the IAC stop operating at any time?All
Ye s®Repair the Harness or Connectors as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 7
7 Ignition On, Engine Not Running
Check Throttle Plate and Linkage for a binding condition.
The Throttle Linkage must be free and the Throttle Plate at the idle
position.
Ensure Throttle Plate is fully closed and against its stop.
Is the Throttle Plate and Linkage okay?All
Ye s®Test Complete.
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
181
DRIVEABILITY
P-1294 TARGET IDLE NOT REACHED ÐContinued
ProCarManuals.com

Verification Tests
VERIFICATION TEST VER-1A APPLICABILITY
No Start Verification
Use this test to verify that a No Start condition has been repaired and that the vehicle can be
returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. Inspect the engine oil for fuel contamination. Replace the oil and filter as necessary
3. Attempt to start the engine.
4. If the No Start condition is still present, refer to the symptom list and perform diagnostic
testing as necessary. Refer to any Technical Service Bulletins that may apply.
5. Run the engine for one warm-up cycle to verify proper operation. With the DRBIIIt, confirm
that no DTC's are present and that all components are functioning properly.
6. If DTC's are present, refer to the symptom list and perform diagnostic testing as necessary.ALL
VERIFICATION TEST VER-2A APPLICABILITY
Non-OBDII Verification
Use this test to verify that a non-OBDII symptom has been repaired and that the vehicle can
be returned to the customer. A non-OBDII symptom is a comprehensive component related
symptom that is not the result of a failed OBDII major monitor.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. With the DRBIIIt, Clear DTC's and Reset Memory (all engine values).
3. Run the engine for one warm-up cycle to verify proper operation.
4. Road test the vehicle. Use all accessories that may be related to this repair.
With the DRBIIIt, confirm that no DTC's are present and that all components are functioning
properly.
6. If this test is being performed after a No Trouble Code test, verify that the symptom is no
longer present. If the symptom is still present, or any other symptom or DTC is present, refer
to the symptom list for further diagnostic testing procedures. Check for any Technical Service
Bulletins that may apply.
7. If there are no DTC's present and all components are functioning properly, repair is
complete.ALL
317
VERIFICATION TESTS
ProCarManuals.com

VERIFICATION TEST VER-5A APPLICABILITY
OBDII Road Test Verification
Use this test to verify that the OBDII symptom has been repaired and that the vehicle can be
returned to the customer. The proper way to verify that an OBDII DTC has been repaired is to
allow the PCM to run and pass the appropriate OBDII monitor(s).
Note: If the Powertrain Control Module has been changed and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for further diagnostic testing
procedures.
3. With the DRBIIIt, Clear DTC's.
4. In order for an OBDII monitor to run, certain pre-test conditions must be met. Refer to the
applicable OBDII monitor pre-test screen on the DRBIIItfor monitor enabling conditions.
5. Operate the vehicle within the enabling conditions and allow the applicable monitor to run.
While the monitor is running, the OBDII monitor screen on the DRBIIItwill display ªIN
PROGRESSº and the DRBIIItwill beep. After the monitor is complete, view the results. Refer
to the appropriate service information as necessary. A monitor may have to fail more than once
in order to set a DTC.
If the monitor fails, or the DTC returns, or any other symptom or DTC is present, refer to the
symptom list for further diagnostic testing procedures. Check for any Technical Service
Bulletins that may apply.
If there are no DTC's present and all components are functioning properly, the repair is
complete.ALL
Powertrain Verification Test VER-5A2 APPLICABILITY
Fuel System Lean/Rich or Misfire Verification
Use this test to verify that the Fuel System Lean, Fuel System Rich, or Misfire symptom has
been repaired and that the vehicle can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret KEY data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for further diagnostic testing
procedures.
3. With the DRBIIIt, monitor the Similar Conditions Window and attempt to duplicate the
conditions that the vehicle was operating at when the DTC was set. If the conditions can be
duplicated, the Good Trip counter will change to one or more.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedures. Check for any Technical Service Bulletins that may apply.
5. If the monitor runs and the Good Trip Counter changes to one or more, the condition is no
longer present. If there are no DTCs and all components are functioning properly, the repair is
complete.ALL
320
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

Powertrain Verification Test VER-5A3 APPLICABILITY
OBDII Monitor Verification
Use this test to verify that the OBDII monitor symptom has been repaired and that the vehicle
can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for further diagnostic testing
procedures.
3. With the DRBIIIt, monitor the pre-test enabling conditions. Operate the vehicle within the
enabling conditions and allow the applicable monitor to run.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedurs. Refer to any Technical Service Bulletins that may apply.
5. If the monitor runs and the Good Trip Counter changes to one or more, the condition is no
longer present.
6. If there are no DTCs and all components are functioning properly, the repair is complete.All
Powertrain Verification Test VER-6A APPLICABILITY
LDP Monitor Verification
Use this test to verify that the LDP monitor symptom has been repaired and that the vehicle
can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and Transponder (ignition key).
1. Inspect the vehicle to ensure that all components are related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for futher diagnostic testing
procedures.
3. With the DRBIIIt, perform the LDP Monitor Test. Follow the instructions on the DRBIIIt
screen.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedures. Refer to any Technical Service Bulletins that mat apply.
5. If the monitor runs and test does not fail, the condition is no longer present.
6. If there are no DTCs and all components are functioning properly, the repair is complete.All
321
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com