2000 CHRYSLER VOYAGER airbag off

VERIFICATION TEST VER-3A APPLICABILITY
Charging System Verification
Use this test to verify that the Charging System symptom has been repaired and that the
vehicle can be returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. With the DRBIIIt, Clear DTC's.
3. Perform generator output test. Refer to the appropriate service information as necessary.
4. Start the engine and set engine speed to 2000 RPM for at least thirty seconds.
5. Turn the ignition OFF.
6. Turn the ignition ON, with the engine not running.
7. With the DRBIIIt, Read the DTC's. If the DTC returns, or any other symptom or DTC is
present, refer to the symptom list for further diagnostic testing procedures. Check for any
Technical Service Bulletins that may apply.
8. If there are no DTC's present and all components are functioning properly, the repair is
complete.All
318
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

VERIFICATION TEST VER-4A APPLICABILITY
Speed Control Verification
Use this test to verify that the Speed Control symptom has been repaired and that the vehicle
can be returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. With the DRBIIIt, Clear DTC's.
3. Road test the vehicle at a speed above 35 MPH.
4. Turn the Speed Control ON.
5. Press and release the Set switch. Verify that the speed control engages.
6. With the Speed Control engaged:
A. Press and hold the ACCEL switch. Verify that the speed increases.
B. Press and hold the SET (or DECEL) switch. Verify that the vehicle speed decreases.
C. Press and release the CANCEL switch. Verify that the Speed Control disengages.
D. Allow the vehicle speed to drop below 25 MPH. Press and release the RESUME switch.
Verify that the previously set vehicle speed is attained.
E. Using caution, press and release the brake pedal. Verify that the Speed Control
disengages.
F. Increase vehicle speed by at least 10 MPH. Press and release the SET switch. Verify the
Speed Control maintains this speed.
G. Press and release the ON/OFF switch (turn the Speed Control OFF.) Verify that the Speed
Control disengages.
If any or all of these functions are not operating properly, refer to the symptom list for the
appropriate diagnostic testing procedures.
7. With the DRBIIIt, Read DTC's. If the DTC returns, or any other symptom or DTC is present,
refer to the symptom list for further diagnostic testing procedures. Check for any Technical
Service Bulletins that may apply.
8. If there are no DTC's present and all components are functioning properly, the repair is
complete.All
319
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

BRAKE SHIFT INTERLOCK SOLENOID (EXCEPT BUILT-UP EXPORT)-2WAYCAV CIRCUIT FUNCTION
1 K29 20WT/PK RED BRAKE WARNING LAMP DRIVER
2 F11 20RD/WT FUSED IGNITION SWITCH OUTPUT (ST-RUN-OFF)
CAMSHAFT POSITION SENSOR - BLACK 3-WAYCAV CIRCUIT FUNCTION
1 K7 18OR 8V SUPPLY
2 K4 18BK/LB SENSOR GROUND
3 K44 18TN/YL CAMSHAFT POSITION SENSOR SIGNAL
CLOCKSPRING C1 - YELLOW 2 WAYCAV CIRCUIT FUNCTION
1 R43 18BK/LB DRIVER AIRBAG LINE 1
2 R45 18DG/LB DRIVER AIRBAG LINE 2
CLOCKSPRING C2 - NATURAL 5 WAYCAV CIRCUIT FUNCTION
1 X3 20BK/RD HORN RELAY CONTROL SENSE
2 X10 20RD/WT (RADIO RE-
MOTE CONTROL)RADIO MUX
3 Z2 20BK/LG (SPEED CON-
TROL)GROUND
4 V37 20RD/LG (SPEED
CONTROLSPEED CONTROL SWITCH SIGNAL
5 X20 20RD/BK (RADIO RE-
MOTE CONTROL)RADIO CONTROL MUX
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
334
CONNECTOR PINOUTS
ProCarManuals.com