2000 CHRYSLER VOYAGER check oil

TABLE OF CONTENTS - Continued
P-1492 BATTERY TEMP SENSOR VOLTAGE TOO HIGH......................18
P-1493 BATTERY TEMP SENSOR VOLTAGE TOO LOW.......................18
P-1594 CHARGING SYSTEM VOLTAGE TOO HIGH...........................19
P-1682 CHARGING SYSTEM VOLTAGE TOO LOW...........................21
* CHECKING CHARGING SYSTEM OPERATION WITH NO DTC'S..............24
DRIVEABILITY
P-0106 BAROMETRIC PRESSURE OUT OF RANGE..........................27
P-0107 MAP SENSOR VOLTAGE TOO LOW.................................30
P-0108 MAP SENSOR VOLTAGE TOO HIGH................................32
P-0112 INTAKE AIR TEMP SENSOR VOLTAGE LOW..........................34
P-0113 INTAKE AIR TEMPERATURE SENSOR VOLT HIGH....................36
P-0117 ECT SENSOR VOLTAGE TOO LOW.................................38
P-0118 ECT SENSOR VOLTAGE TOO HIGH.................................40
P-0121 TPS VOLTAGE DOES NOT AGREE WITH MAP........................42
P-0122 THROTTLE POSITION SENSOR VOLTAGE LOW......................45
P-0123 THROTTLE POSITION SENSOR VOLTAGE HIGH......................48
P-0125 CLOSED LOOP TEMP NOT REACHED...............................51
P-0131 1/1 O2 SENSOR VOLTAGE SHORTED TO GROUND...................53
P-0132 1/1 O2 SENSOR SHORTED TO VOLTAGE............................55
P-0133 1/1 O2S SLOW RESPONSE........................................57
P-0134 1/1 O2 SENSOR STAYS AT CENTER................................60
P-0135 O2S HEATER FAILURE............................................62
P-0137 1/2 O2 SENSOR VOLTAGE SHORTED TO GROUND...................64
P-0138 1/2 O2 SENSOR SHORTED TO VOLTAGE............................66
P-0139 1/2 O2S SLOW RESPONSE........................................68
P-0140 1/2 O2 SENSOR STAYS AT CENTER................................71
P-0141 1/2 O2S HEATER FAILURE........................................73
P-0171±1/1 FUEL SYSTEM LEAN..........................................75
P-0201 INJECTOR #1 CONTROL CIRCUIT..................................83
P-0202 INJECTOR #2 CONTROL CIRCUIT..................................86
P-0203 INJECTOR #3 CONTROL CIRCUIT..................................89
P-0204 INJECTOR #4 CONTROL CIRCUIT..................................92
P-0205 INJECTOR #5 CONTROL CIRCUIT..................................95
P-0206 INJECTOR #6 CONTROL CIRCUIT..................................97
P-0300 MULTIPLE CYLINDER MIS-FIRE...................................100
P-0301 CYLINDER #1 MIS-FIRE..........................................100
P-0302 CYLINDER #2 MIS-FIRE..........................................100
P-0303 CYLINDER #3 MIS-FIRE..........................................100
P-0304 CYLINDER #4 MIS-FIRE..........................................100
P-0305 CYLINDER #5 MIS-FIRE..........................................104
P-0306 CYLINDER #6 MIS-FIRE..........................................104
P-0320 NO CRANK REFERENCE SIGNAL AT PCM..........................108
P-0340 NO CAM SIGNAL AT PCM........................................113
P-0351 IGNITION COIL #1 PRIMARY CIRCUIT..............................122
P-0352 IGNITION COIL #2 PRIMARY CIRCUIT..............................125
P-0353 IGNITION COIL #3 PRIMARY CIRCUIT..............................128
P-0401 EGR SYSTEM FAILURE..........................................131
P-0403 EGR SOLENOID CIRCUIT........................................133
P-0420 1/1 CATALYTIC CONVERTER EFFICIENCY..........................136
P-0441 EVAP PURGE FLOW MONITOR FAILURE...........................138
P-0442 EVAP LEAK MONITOR SMALL LEAK DETECTED.....................140
P-0455 EVAP LEAK MONITOR LARGE LEAK DETECTED.....................140
ii
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Turn Ignition On (Engine Off).
During the following voltage drop measurement, wiggle wires between O2S Connec-
tor and PCM Connector.
Using a voltmeter, backprobe O2S (Signal) Circuit between O2S Connector (O2S
Signal) and PCM Connector (O2S Signal).
While wiggling wires, is the voltage drop reading below 0.10 VDC?All
Ye s®Go To 4
No®Repair poor connection (high resistance) on O2S Signal Circuit.
Perform VERIFICATION TEST VER-5A3.
4 At this time the 1/1 O2S SLOW RESPONSE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME pay particular attention to the fault setting condi-
tions, such as speed, temp, load, and map vacuum.
Does the 1/1 O2S SLOW RESPONSE reoccur?All
Ye s®Go To 5
No®The 1/1 O2S SLOW RESPONSE no longer exists.
Perform VERIFICATION TEST VER-5A3.
5 The following are possible causes for O2 Sensor Slow Response: exhaust leak, fuel
contamination, O2 sensor failure, electrical wiring connectors, electrical mechanical,
and O2 heater failure.
Start the Engine.
NOTE: Check the exhaust for excessive smoke caused by oil or coolant
consumption.
Is there an oil or coolant consumption condition present?All
Ye s®Repair engine mechanical as necessary and replace O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
No®Go To 6
6 The following are possible causes for O2 Sensor Slow Response: exhaust leak, fuel
contamination, O2 sensor failure, electrical wiring connectors, electrical mechanical,
and O2 heater failure.
Start the Engine.
Check the Exhaust System for leaks between the Engine and the catalyst.
Are there any leaks?All
Ye s®Repair or replace leaking Exhaust System as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Go To 7
7 The following are possible causes for O2 Sensor Slow Response: exhaust leak, fuel
contamination, O2 sensor failure, electrical wiring connectors, electrical mechanical,
and O2 heater failure.
Turn Ignition On (Engine Off).
Using a voltmeter, backprobe O2S (Signal) Circuit between O2S Connector (O2S
Signal) and PCM Connector (O2S Signal).
Is the voltage drop reading below 0.10 VDC?All
Ye s®Go To 8
No®Repair poor connection (high resistance) on O2S Signal Circuit.
Perform VERIFICATION TEST VER-5A3.
58
DRIVEABILITY
P-0133 1/1 O2S SLOW RESPONSE ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Turn Ignition On (Engine Off).
During the following voltage drop measurement, wiggle wires between O2S Connec-
tor and PCM Connector.
Using a voltmeter, backprobe O2S (Signal) Circuit between O2S Connector (O2S
Signal) and PCM Connector (O2S Signal).
While wiggling wires, is the voltage drop reading below 0.10 VDC?All
Ye s®Go To 4
No®Repair poor connection (high resistance) on O2S Signal Circuit.
Perform VERIFICATION TEST VER-5A3.
4 At this time the 1/2 O2S SLOW RESPONSE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/2 O2S SLOW RESPONSE reoccur?All
Ye s®Go To 5
No®The 1/2 O2S SLOW RESPONSE no longer exists.
Perform VERIFICATION TEST VER-5A3.
5 The following are possible causes for O2 Sensor Slow Response: exhaust leak, fuel
contamination, O2 sensor failure, electrical wiring connectors, electrical mechanical,
and O2 heater failure.
Start the Engine.
NOTE: Check the exhaust for excessive smoke caused by oil or coolant
consumption.
Is there an oil or coolant consumption condition present?All
Ye s®Repair engine mechanical as necessary and replace O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
No®Go To 6
6 The following are possible causes for O2 Sensor Slow Response: exhaust leak, fuel
contamination, O2 sensor failure, electrical wiring connectors, electrical mechanical,
and O2 heater failure.
Start the Engine.
Check the Exhaust System for leaks between the Engine and the catalyst.
Are there any leaks?All
Ye s®Repair or replace leaking Exhaust System as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Go To 7
7 The following are possible causes for O2 Sensor Slow Response: exhaust leak, fuel
contamination, O2 sensor failure, electrical wiring connectors, electrical mechanical,
and O2 heater failure.
Turn Ignition On (Engine Off).
Using a voltmeter, backprobe O2S (Signal) Circuit between O2S Connector (O2S
Signal) and PCM Connector (O2S Signal).
Is the voltage drop reading below 0.10 VDC?All
Ye s®Go To 8
No®Repair poor connection (high resistance) on O2S Signal Circuit.
Perform VERIFICATION TEST VER-5A3.
69
DRIVEABILITY
P-0139 1/2 O2S SLOW RESPONSE ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
12 Engine Off.
Connect a suitable engine analyzer to the engine.
Allow the Engine to idle.
NOTE: If the Engine will not idle, maintain a constant RPM above idle.
NOTE: Set the scope to read display or parade pattern.
Remove any spark plug wire.
Observe the Secondary KV Line.
Is the open secondary voltage at least 25 KV?All
Ye s®Go To 13
No®Replace the Ignition Coil.
Perform VERIFICATION TEST VER-5A2.
13 Engine Off.
Connect a suitable engine analyzer to the engine.
Allow the Engine to idle.
NOTE: If the Engine will not idle, maintain a constant RPM above idle.
NOTE: Set the scope to read display or parade pattern.
Follow the equipment manufacturer's procedure for pattern analysis.
Is the secondary ignition pattern OK?All
Ye s®Go To 14
No®Repair the indicated component in the Secondary Ignition Sys-
tem.
Perform VERIFICATION TEST VER-5A2.
14 The following are possible causes for mis-fire:
Injector harness connectors, ignition coil circuit, spark plug, mechanical engine
problem, PCM power grounds, irregular cam and crank signal, injectors, restricted
exhaust, intake restriction, PCM, Evap System, EGR System, damaged trigger
wheel, and
accessory drive belts.
Do any of the above causes exist?All
Ye s®Repair as necessary.
Perform VERIFICATION TEST VER-5A2.
No®Go To 15
15The following additional items should be checked as possible mechanical
problems:
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions
ENGINE PCV SYSTEM - must flow freely
ENGINE DRIVE SPROCKETS - must be properly positioned
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?All
Ye s®Repair as necessary.
Perform VERIFICATION TEST VER-5A2.
No®Test Complete.
103
DRIVEABILITY
P-0300 MULTIPLE CYLINDER MIS-FIRE ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
12 Engine Off.
Connect a suitable engine analyzer to the engine.
Allow the Engine to idle.
NOTE: If the Engine will not idle, maintain a constant RPM above idle.
NOTE: Set the scope to read display or parade pattern.
Follow the equipment manufacturer's procedure for pattern analysis.
Is the secondary ignition pattern OK?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 13
No®Repair the indicated component in the Secondary Ignition Sys-
tem.
Perform VERIFICATION TEST VER-5A2.
13 With the DRB, read the FREEZE FRAME DATA.
Use the freeze frame data and attempt to determine the cause of the misfire.
In the FREEZE FRAME, is the ENGINE RPM over 3000 and the operating temp
normal?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Lab scope cam and crank sensor, check valve timing, running
vacuum test.
Perform VERIFICATION TEST VER-5A2.
No®Go To 14
14The following additional items should be checked as possible mechanical
problems:
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions
ENGINE PCV SYSTEM - must flow freely
ENGINE DRIVE SPROCKETS - must be properly positioned
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair as necessary.
Perform VERIFICATION TEST VER-5A2.
No®Go To 15
15 The following are other possible causes for mis-fire:
Injector harness connectors, ignition coil circuit, spark plug, mechanical engine
problem, PCM power grounds, irregular cam and crank signal, injectors, restricted
exhaust, intake restriction, PCM, Evap System, EGR System, damaged trigger
wheel, and
accessory drive belts.
Do any of the above causes exist?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair as necessary.
Perform VERIFICATION TEST VER-5A2.
No®Test Complete.
107
DRIVEABILITY
P-0305 CYLINDER #5 MIS-FIRE ÐContinued
ProCarManuals.com

Symptom:
P-0351 IGNITION COIL #1 PRIMARY CIRCUIT
When Monitored and Set Condition:
P-0351 IGNITION COIL #1 PRIMARY CIRCUIT
When Monitored: With battery voltage greater than 8 volts during engine cranking or
greater than 12 volts with engine running, and none of the coils in dwell when checked.
Set Condition: Peak current is not achieved with 2.5ms of dwell. It takes 3 seconds during
cranking or up to 6 seconds while running to set.
POSSIBLE CAUSES
ASD OUTPUT CIRCUIT OPEN
IGNITION COIL #1 CONNECTOR TERMINAL OBSERVABLE DEF
IGNITION COIL #1 DRIVER CIRCUIT OPEN
IGNITION COIL #1 DRIVER CIRCUIT SHORTED TO GROUND
IGNITION COIL CIRCUIT WIRING HARNESS INTER DEFECT
IGNITION COIL CIRCUIT WIRING HARNESS OBS DEFECT
IGNITION COIL #1 RESISTANCE ABOVE 2.0 OHMS
PCM DEFECTIVE (IGN COIL #1)
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, read codes.
Is the Global Good Trip displayed and equal to 0?All
Ye s®Go To 2
No®Go To 8
2 Ignition Off
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the DRB, actuate Ignition Coil #1.
With a Voltmeter, measure the ASD Output Circuit.
Is the voltage above 10.0 volts?All
No®Repair the open ASD Output Circuit.
Perform Powertrain Verification Test VER-5A.
Ye s®Go To 3
122
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
Is any terminal damaged, pushed out or miswired?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 4
4 Ignition Off
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the Ignition Coil #1 Primary Circuit for resistance.
Is the resistance below 2.0 ohms?All
Ye s®Go To 5
No®Replace the Ignition Coil.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Ignition Coil #1 Driver Circuit for resistance to
ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Ignition Coil #1 Driver Circuit for a short to ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, test the resistance of #1 Driver Circuit.
Is the resistance below 5.0 ohms?All
Ye s®Go To 7
No®Repair the open Ignition Coil #1 Driver Circuit.
Perform Powertrain Verification Test VER-5A.
7 If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-5A.
8 Ignition Off
Start Engine.
Wiggle Wiring Harness from the Ignition Coil to the PCM.
Does the engine miss or stall?All
Ye s®Repair as necessary where wiggling caused problem to appear.
Perform Powertrain Verification Test VER-5A.
No®Go To 9
123
DRIVEABILITY
P-0351 IGNITION COIL #1 PRIMARY CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-0352 IGNITION COIL #2 PRIMARY CIRCUIT
When Monitored and Set Condition:
P-0352 IGNITION COIL #2 PRIMARY CIRCUIT
When Monitored: With battery voltage greater than 8 volts during engine cranking or
greater than 12 volts with engine running, and none of the coils in dwell when checked.
Set Condition: Peak current is not achieved with 2.5ms of dwell. It takes 3 seconds during
cranking or up to 6 seconds while running to set.
POSSIBLE CAUSES
AUTO SHUTDOWN OUTPUT CIRCUIT OPEN
IGNITION COIL #2 CONNECTOR TERMINAL OBSERVABLE DEF
IGNITION COIL #2 DRIVER CIRCUIT OPEN
IGNITION COIL #2 DRIVER CIRCUIT SHORTED TO GROUND
IGNITION COIL CIRCUIT WIRING HARNESS INTER DEFECT
IGNITION COIL CIRCUIT WIRING HARNESS OBS DEFECT
IGNITION COIL #2 DEFECTIVE
PCM DEFECTIVE (IGN COIL #2)
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, read codes.
Is the Global Good Trip displayed and equal to 0?All
Ye s®Go To 2
No®Go To 8
2 Ignition Off
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the DRB, actuate Ignition Coil #2.
With a Voltmeter, measure the ASD Output Circuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 3
No®Repair the open ASD Output Circuit.
Perform Powertrain Verification Test VER-2A.
125
DRIVEABILITY
ProCarManuals.com