2000 CHRYSLER VOYAGER ignition relay

Symptom:
* CHECKING OXYGEN SENSOR HEATER
POSSIBLE CAUSES
1/2 O2 SENSOR VOLTAGE BTWN 0.4 V & 0.6 V
1/1 O2 SENSOR DEFECTIVE
1/2 O2 SENSOR DEFECTIVE
ASD RELAY OUTPUT CIRCUIT OPEN (1/1 O2 SEN)
ASD RELAY OUTPUT CIRCUIT OPEN (1/2 O2 SEN)
HEATER GROUND CIRCUIT OPEN (1/1 O2 SEN)
HEATER GROUND CIRCUIT OPEN (1/2 O2 SEN)
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, actuate the ASD O2 Sensor Heater test.
Wait two minutes for O2 Sensor voltage to stabilize.
Read the Upstream O2 Sensor voltage.
Is the voltage of the Upstream O2 Sensor between 0.4 and 0.6 volts?All
Ye s®Go To 2
No®Go To 5
2Note: The O2 Sensor voltage staying between 0.4 V and 0.6 V indicates a
problem with that Sensor Circuit.
Ignition Off
Disconnect the Upstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Turn key on.
With the DRB, actuate the O2 Sensor Heater test.
Using a Voltmeter, measure the ASD Relay Output Circuit at Sensor Connector.
Is the voltage above 10.0 volts?All
Ye s®Go To 3
No®Repair the open ASD Relay Output Circuit from O2 sensor
connector back to splice.
Perform Powertrain Verification Test VER-2A.
3 Ignition Off
Disconnect the Upstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance between the Heater Ground Circuit and
a good ground.
Is the resistance below 5.0 ohms?All
Ye s®Go To 4
No®Repair the open Heater Ground Circuit to the Upstream O2
Sensor.
Perform Powertrain Verification Test VER-2A.
247
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 If there are no potential causes remaining, the Upstream O2 Sensor is assumed to be
defective.
View repair options.All
Repair
Replace the Upstream O2 Sensor.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Turn key on.
With the DRB, actuate the O2 Sensor Heater test.
Wait two minutes for O2 Sensor voltage to stabilize.
With the DRB, read the Downstream O2 Sensor voltage.
Is the voltage of the Downstream O2 Sensor between 0.4 and 0.6 volts?All
Ye s®Go To 6
No®Test complete.
6Note: The O2 Sensor voltage staying between 0.4 and 0.6 V indicates a
problem with that Sensor Circuit.
Ignition Off
Disconnect the Downstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Turn key on.
With the DRB, actuate the O2 Sensor Heater test.
Using a Voltmeter, measure the ASD Relay Output Circuit in Sensor Connector.
Is the voltage above 10.0 volts?All
Ye s®Go To 7
No®Repair the open ASD Relay Output Circuit from O2 Sensor
Connector back to splice.
Perform Powertrain Verification Test VER-2A.
7 Ignition Off
Disconnect the Downstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance between the Heater Ground Circuit and
a good ground.
Is the resistance below 5.0 ohms?All
Ye s®Go To 8
No®Repair the open Heater Ground Circuit to the Downstream O2
Sensor.
Perform Powertrain Verification Test VER-2A.
8 If there are no potential causes remaining, the Downstream O2 Sensor is assumed to
be defective.
View repair options.All
Repair
Replace the Downstream O2 Sensor.
Perform Powertrain Verification Test VER-2A.
248
DRIVEABILITY
* CHECKING OXYGEN SENSOR HEATER ÐContinued
ProCarManuals.com

Symptom:
*(NO RESPONSE(CONDITION
POSSIBLE CAUSES
IGNITION NOT ON
DIAGNOSTIC READ-OUT BOX ADAPTER CABLE DEFECTIVE
FUEL PUMP DEFECTIVE
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
PCM GROUNDS OPEN
FUEL PUMP RELAY OUT CKT INTERMITTENT SHORT TO GRND
FUEL PUMP RELAY OUTPUT CIRCUIT SHORT TO GROUND
SCI RECEIVE CIRCUIT OPEN
SCI RECEIVE CIRCUIT SHORT TO GROUND
SCI TRANSMIT CIRCUIT OPEN
SCI TRANSMIT CIRCUIT SHORTED TO GROUND
FUSED B(+) CIRCUIT OPEN BETWEEN FUSE AND BATTERY
DIAGNOSTIC READ-OUT BOX DEFECTIVE
PCM DEFECTIVE (NO RESPONSE)
FUSED B(+) CIRCUIT OPEN BETWEEN FUSE AND PCM
FUSED B(+) CIRCUIT SHORT TO GROUND
TEST ACTION APPLICABILITY
1 Attempt to start vehicle.
Does the vehicle start?All
Ye s®Go To 2
No®Go To 12
2 Was the Ignition on when the ªNo Responseº message was displayed? All
Ye s®Go To 3
No®Turn the ignition on to get a response.
3 Ignition off.
Using an Ohmmeter, measure the DLC ground circuit (terminals 4 and 5) to ground.
Is the resistance below 5.0 ohms for each measurement?All
Ye s®Go To 4
No®Repair the open ground circuit(s).
Perform Powertrain Verification Test VER-1A.
272
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
14 Ignition Off.
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
With a voltmeter, mesure the Fused B(+) Curcuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 15
No®Go To 16
15 If there are no potential causes remaining, replace the Powertrain Control Module.
View repair options.All
Replace the Powertrain Control Module.
Perform the Powertrain Verification Test VER-1A.
16 Remove Fuel Pump Fuse from the Power Distribution Center.
Inspect the Fuse.
Is the fuse OK?All
Ye s®Go To 17
No®Go To 18
17 Ignition On.
Remove the Fuel Pump Fuse from the PCM.
With a voltmeter, measure the B(+) side of the Fuse Socket.
Is the voltage above 10.0 volts?All
Ye s®Repair the opem B(+) circuit between the Fuse and the PCM.
Perform Powertrain Verification Test VER-1A.
No®Repair the opem B(+) circuit between the Fuse and the battery.
Perform Powertrain Verification Test VER-1A.
18 Ignition Off
Disconnect the Fuel Pump Relay.
Disconnect the Fuel Pump Electrical Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Fuel Pump Relay Output Circuit to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Fuel Pump Relay Output Circuit for a short to ground.
Perform Powertrain Verification Test VER-1A.
No®Go To 19
19 If there are no potential causes remaining, the Fuel Pump is assumed to be defective.
View repair options.All
Repair
Replace the Fuel Pump. Replace Fuel Pump Fuse.
Perform Powertrain Verification Test VER-1A.
275
STARTING
*(NO RESPONSE(CONDITION ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
15 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Ignition On , Engine Not Running.
With a Voltmeter, measure the Fuel Pump Relay Fused B(+) Circuit.
Is the voltage above 10.0 volts?ENGINE - 3.0L V6
Ye s®Go To 16
No®Repair the open Fuel Pump Relay Fused B(+) Circuit.
Perform Powertrain Verification Test VER-1A.
16 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note; Check Connectors - clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
Ignition On, Engine Not Running.
Actuate the ASD Fuel System test.
With a Voltmeter, measure the Fuel Pump Relay Output Circuit.
Is the voltage above 10.0 volts?ENGINE - 3.0L V6
Ye s®Go To 17
No®Repair the open Fuel Pump Relay Output Circuit.
Perform Powertrain Verification Test VER-1A.
17 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Install a substitute Relay of the same part number for the Fuel Pump Relay.
Attempt to start the Engine.
Does the engine start?ENGINE - 3.0L V6
Ye s®Replace the Fuel Pump Relay.
Perform Powertrain Verification Test VER-1A.
No®Go To 18
18 Ignition off.
If there are no potential causes remaining, the Fuel Pump is assumed to be defective.
View repair options.ENGINE - 3.0L V6
Repair
Replace the Fuel Pump.
Perform Powertrain Verification Test VER-1A.
19Note: Ensure the SKIM has proper communication and that there are no
SKIM DTC's present before continuing.
Ignition Off.
Ensure the Throttle Cables are not holding the Throttle open.
Is the Throttle held open?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Repair condition that holds the Throttle Body open.
No®Go To 20
282
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
28 Record the Fuel Pressure Gauge reading.
Ignition Key Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pressure Gauge.
Install adapter 6631 between Fuel Filter Outlet and Chassis Fuel Supply Tube.
Connect Fuel Pressure Gauge to adapter 6631.
Ignition On, Engine Not Running.
With DRB, actuate the ASD Fuel System.
Record the Fuel Pressure Gauge reading.
Compare this reading with the previous reading.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Repair restriction in Chassis Fuel Supply Line between Fuel
Filter and Fuel Rail.
Perform Powertrain Verification Test VER-1A.
No®Go To 29
29 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Repair
Replace Fuel Pump Module.
Perform Powertrain Verification Test VER-1A.
30 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note: Check connectors - Clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
With an Ohmmeter, measure the Fuel Pump Ground Circuit.
Is the resistance below 5.0 ohms?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 31
No®Repair the open Fuel Pump Ground Circuit.
Perform Powertrain Verification Test VER-1A.
31 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Ignition On , Engine Not Running.
With a Voltmeter, measure the Fuel Pump Relay Fused B(+) Circuit.
Is the voltage above 10.0 volts?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 32
No®Repair the open Fuel Pump Relay Fused B(+) Circuit.
Perform Powertrain Verification Test VER-1A.
285
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
32 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note; Check connectors - Clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
Ignition On, Engine Not Running.
Actuate the ASD Fuel System test.
With a Voltmeter, measure the Fuel Pump Relay Output Circuit.
Is the voltage above 10.0 volts?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 33
No®Repair the open Fuel Pump Relay Output Circuit.
Perform Powertrain Verification Test VER-1A.
33 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Install a substitute Relay of the same part number for the Fuel Pump Relay.
Attempt to start the Engine.
Does the Engine start?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Replace the Fuel Pump Relay.
Perform Powertrain Verification Test VER-1A.
No®Go To 34
34 Ignition Off.
If there are no potential causes remaining, the Fuel Pump is assumed to be defective.
View repair options.ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Repair
Replace the Fuel Pump.
Perform Powertrain Verification Test VER-1A.
286
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

Symptom:
* CHECKING THE SECONDARY IGNITION SYSTEM
POSSIBLE CAUSES
GOOD SPARK AT SPARK PLUG #1
AUTO SHUTDOWN RELAY OUTPUT CIRCUIT OPEN
AUTO SHUTDOWN RELAY OUTPUT CIRCUIT OPEN
COIL SECONDARY CABLE DEFECTIVE
FUSED B(+) CIRCUIT OPEN
FUSED B(+) CIRCUIT OPEN
IGNITION COIL CONNECTOR OBSERVABLE DEFECT
IGNITION COIL CONNECTOR OBSERVABLE DEFECT
IGNITION COIL DEFECTIVE
IGNITION COIL SECONDARY CABLE #1 DEFECTIVE
IGNITION COIL SECONDARY CABLE #4 DEFECTIVE
SECONDARY IGNITION COMPONENT(S) DEFECTIVE
SPARK PLUG CABLE #1 DEFECTIVE
AUTO SHUTDOWN RELAY DEFECTIVE
AUTO SHUTDOWN RELAY DEFECTIVE
IGNITION COIL DEFECTIVE
IGNITION COIL DEFECTIVE (RESISTANCE OUT OF RANGE)
SPARK PLUG #1 OR #4 DEFECTIVE
GOOD SPARK AT SPARK PLUG #1
GOOD SPARK AT SPARK PLUG #1
TEST ACTION APPLICABILITY
1 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #1.
Connect the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Warning: Ensure that there are no Fuel or Fuel vapors present in or near
the Engine compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 3.0L V6
Ye s®Refer to Symptom list for further diagnostic tests.
No®Go To 2
288
STARTING
ProCarManuals.com