2000 CHRYSLER VOYAGER ignition

TEST ACTION APPLICABILITY
9 Ignition off.
If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
10 Ignition off.
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 11
11 Start Engine.
Note: The Engine must be running before continuing test.
Wiggle Wiring Harness from ASD Relay to the Powertrain Control Module.
With the DRB, read Trouble Codes.
Did trouble code9No ASD Relay Output Voltage at PCM9reset?All
Ye s®Repair as necessary where wiggling caused the Trouble Code to be
set.
Perform Powertrain Verification Test VER-2A.
No®Test Complete.
190
DRIVEABILITY
P-1389 NO ASD RELAY OUTPUT VOLTAGE AT PCM ÐContinued
ProCarManuals.com

Symptom:
P-1391 INTERMITTENT LOSS OF CMP OR CKP
When Monitored and Set Condition:
P-1391 INTERMITTENT LOSS OF CMP OR CKP
When Monitored: Engine running over 7 seconds.
Set Condition: When the expected cam signal level disagrees with the actual cam signal
level.
POSSIBLE CAUSES
CKP SENSOR CKT WIRING HARNESS INTER DEF
CMP SENSOR SIGNAL CKT WIRING HARNESS INTER DEF
CAMSHAFT POSITION SENSOR DEFECTIVE
CAMSHAFT SPROCKET DEFECTIVE
CRANKSHAFT DEFECTIVE
CRANKSHAFT POSITION SENSOR DEFECTIVE
DISTRIBUTOR PULSE RING DEFECTIVE
FLYWHEEL DEFECTIVE
CAMSHAFT TARGET MAGNET DEFECTIVE
CAMSHAFT THRUST PLATES(S) NOT ATTACHED
CKP SENSOR CONNECTOR TERMINALS OBS DEF
CKP SENSOR CONNECTOR TERMINALS OBS DEFECT
PCM CONN TERMINALS OBS DEF (CKP SENSOR)
PCM CONN TERMINALS OBS DEF (CMP SENSOR)
CAMSHAFT/CYLINDER HEAD DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off.
At the CMP Sensor, backprobe the CMP Sensor Signal Circuit with the Oscilloscope
voltage measurement lead.
Start the Engine and observe the CMP Sensor voltage pattern on the Oscilloscope.
Are there any of the Camshaft Position Sensor Signals missing?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Go To 2
No®Go To 6
191
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
2 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 3
3 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 4
4 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the Camshaft Position Sensor.
Inspect the Camshaft Sprocket. See pertinent service information for instructions.
Is the Camshaft Sprocket okay?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Go To 5
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the CMP Sensor.
Inspect the Camshaft Thrust Plate(s).
Are the Camshaft Thrust Plate(s) attached?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Replace the Camshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Repair or replace the Camshaft Thrust Plate(s) as necessary.
Perform Powertrain Verification Test VER-5A.
6 Start Engine.
At PCM, backprobe CMP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CMP Sensor Circuit from Sensor to
PCM.
Were any signals missing when the wiggle test was conducted?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Note where wiggling the Wires caused a missing CMP Sensor
Signal. Repair Camshaft and Crankshaft Wiring Harness as
necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 7
192
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
7 Ignition Off.
At the CKP Sensor, backprobe the CKP Sensor Signal Circuit with the Oscilloscope's
voltage measurement lead.
Start the Engine and observe the CKP Sensor voltage pattern on the Oscilloscope.
Are any Crankshaft Position Sensor Signals missing?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Go To 8
No®Go To 11
8 Ignition Off.
Disconnect the CKP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 9
9 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 10
10 Ignition Off
Remove the Crankshaft Position (CKP) Sensor.
Inspect the Slots in the Flywheel for debris or damage.
Is the Flywheel damaged?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair or replace as necessary.
Perform Powertrain Verification Test VER-5A.
No®Replace the Crankshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
11 Start Engine.
At PCM, backprobe CKP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CKP Sensor Circuit from Sensor to
PCM.
Were any CKP Sensor Signals missing when the wiggle test was conducted?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Note where wiggling the wires caused a missing CKP Sensor
signal. Repair Camshaft and Crankshaft Wire Harness as neces-
sary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
193
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
12 Ignition Off.
At the CMP Sensor, backprobe the CMP Sensor Signal Circuit with the Oscilloscope
voltage measurement lead.
Start the Engine and observe the CMP Sensor voltage pattern on the Oscilloscope.
Are there any of the Camshaft Position Sensor Signals missing?ENGINE - 3.0L V6
Ye s®Go To 13
No®Go To 16
13 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 14
14 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 15
15 Ignition Off.
Remove Distributor Cap and Rotor.
Inspect the Pulse Ring for damage or misalignment.
Is the Pulse Ring okay?ENGINE - 3.0L V6
Ye s®Replace the Camshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Repair or replace the Distributor Pulse Ring as necessary.
Perform Powertrain Verification Test VER-5A.
16 Start Engine.
At PCM, backprobe CMP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CMP Sensor Circuit from Sensor to
PCM.
Were any signals missing when the wiggle test was conducted?ENGINE - 3.0L V6
Ye s®Note where wiggling the Wires caused a missing CMP Sensor
Signal. Repair Camshaft and Crankshaft Wiring Harness as
necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 17
194
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
17 Ignition Off.
At the CKP Sensor, backprobe the CKP Sensor Signal Circuit with the Oscilloscope's
voltage measurement lead.
Start the Engine and observe the CKP Sensor voltage pattern on the Oscilloscope.
Are any Crankshaft Position Sensor Signals missing?ENGINE - 3.0L V6
Ye s®Go To 18
No®Go To 21
18 Ignition Off.
Disconnect the CKP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 19
19 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 20
20 Ignition Off.
Remove the Crankshaft Position (CKP) Sensor.
Inspect the Slots in the Flywheel for debris or damage.
Is the Flywheel damaged?ENGINE - 3.0L V6
Ye s®Repair or replace as necessary.
Perform Powertrain Verification Test VER-5A.
No®Replace the Crankshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
21 Start Engine.
At PCM, backprobe CKP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CKP Sensor Circuit from Sensor to
PCM.
Were any CKP Sensor Signals missing when the wiggle test was conducted?ENGINE - 3.0L V6
Ye s®Note where wiggling the wires caused a missing CKP Sensor
signal. Repair Camshaft and Crankshaft Wire Harness as neces-
sary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
195
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
22 Ignition Off.
At the CMP Sensor, backprobe the CMP Sensor Signal Circuit with the Oscilloscope
voltage measurement lead.
Start the Engine and observe the CMP Sensor voltage pattern on the Oscilloscope.
Are there any of the Camshaft Position Sensor Signals missing?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Go To 23
No®Go To 27
23 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 24
24 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 25
25 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove & inspect the CMP Sensor & Target Magnet for damage or misalignment.
Is the Camshaft Target Magnet okay?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Go To 26
No®Repair or replace Camshaft Target Magnet as necessary.
Perform Powertrain Verification Test VER-5A.
26 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove and inspect the CMP Sensor and Target Magnet for damage or mis-
alignment.
Check Camshaft endplay per pertinent service information.
Is the Camshaft endplay within specs?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Replace the Camshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Repair or replace Camshaft/Cylinder Head as necessary.
Perform Verification Test VER-5A.
196
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
27 Start Engine.
At PCM, backprobe CMP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CMP Sensor Circuit from Sensor to
PCM.
Were any signals missing when the wiggle test was conducted?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Note where wiggling the Wires caused a missing CMP Sensor
Signal. Repair Camshaft and Crankshaft Wiring Harness as
necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 28
28 Ignition Off.
At the CKP Sensor, backprobe the CKP Sensor Signal Circuit with the Oscilloscope's
voltage measurement lead.
Start the Engine and observe the CKP Sensor voltage pattern on the Oscilloscope.
Are any Crankshaft Position Sensor Signals missing?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Go To 29
No®Test Complete.
29 Ignition Off.
Disconnect the CKP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 30
30 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 31
31 Ignition Off.
Remove the Crankshaft Position (CKP) Sensor.
Inspect the Crankshaft notches for debris or damage.
Are the Crankshaft notches damaged?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Repair or replace the Crankshaft as necessary.
Perform Powertrain Verification Test VER-5A.
No®Replace the Crankshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
197
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com