2000 CHRYSLER VOYAGER engine

Symptom:
P-0204 INJECTOR #4 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0204 INJECTOR #4 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR #4 DEFECTIVE
INJECTOR #4 DRIVER CIRCUIT OPEN
INJECTOR #4 DRIVER CIRCUIT SHORTED TO GROUND
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?ALL
Ye s®Go To 2
No®Go To 7
2Note: It may be necessary to remove the Intake Plenum in the following
steps.
Key off.
Disconnect the #4 Injector Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #4.
Is the resistance between 10.0 and 16.0 ohms?ALL
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
92
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3Note: It may be necessary to remove the Intake Plenum in the following
steps.
Disconnect the #4 Injector Connector.
Note: Check connectors - Clean/repair as necessary.
Turn ignition on.
With the DRB, actuate the Auto Shutdown Relay.
Using a Voltmeter, measure the ASD Relay Output voltage.
Does the voltage cycle high and low?ALL
Ye s®Go To 4
No®Repair the open ASD Relay Output Circuit.
Perform Powertrain Verification Test VER-5A.
4Note: It may be necessary to remove the Intake Plenum in the following
steps.
Key off.
Disconnect the Injector #4 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure across the Injector #4 Driver Circuit from the PCM to
the Injector.
Is the resistance below 5.0 ohms?ALL
Ye s®Go To 5
No®Repair the open Injector #4 Driver Circuit.
Perform Powertrain Verification Test VER-5A.
5Note: It may be necessary to remove the Intake Plenum in the following
steps.
Key off.
Disconnect the #4 Injector Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #4 Driver Circuit to ground.
Is the resistance below 5.0 ohms?ALL
Ye s®Repair the Injector #4 Control Circuit for a short to ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.ALL
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-5A.
7 Engine Running
Wiggle Wiring Harness from the Injector to the PCM.
Does the engine miss or stall?ALL
Ye s®Repair as necessary where wiggling caused the problem to
appear.
Perform Powertrain Verification Test VER-5A.
No®Go To 8
93
DRIVEABILITY
P-0204 INJECTOR #4 CONTROL CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-0205 INJECTOR #5 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0205 INJECTOR #5 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR #5 DEFECTIVE
INJECTOR #5 DRIVER CIRCUIT OPEN
INJECTOR #5 DRIVER CIRCUIT SHORT TO GROUND
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Disconnect Injector #5 Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #5.
Is the resistance between 10.0 and 16.0 ohms?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
3 Ignition Off
Disconnect Injector #5 Connector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
With the DRB, actuate the Auto Shutdown Relay.
Using a Voltmeter, measure the ASD Relay Output voltage.
Does the voltage cycle high and low?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 4
No®Repair the open ASD Relay Output Circuit.
Perform Powertrain Verification Test VER-5A.
95
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Ignition Off
Disconnect Injector #5 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #5 Driver Circuit from the PCM to the
Injector.
Is the resistance below 5.0 ohms?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 5
No®Repair the open Injector #5 Driver Circuit.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off
Disconnect Injector #5 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #5 Driver Circuit to ground.
Is the resistance below 5.0 ohms?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair the Injector #5 Driver Circuit for a short to ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-5A.
7 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 8
8 Engine Running
Wiggle Wiring Harness from the Injector to the PCM.
Does the engine miss or stall?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair as necessary where wiggling caused the problem to
appear.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
96
DRIVEABILITY
P-0205 INJECTOR #5 CONTROL CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-0206 INJECTOR #6 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0206 INJECTOR #6 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
AUTO SHUTDOWN RELAY OUTPUT CIRCUIT OPEN
INJECTOR #6 DEFECTIVE (RESISTANCE OUT OF RANGE)
INJECTOR #6 DRIVER CIRCUIT OPEN
INJECTOR #6 DRIVER CIRCUIT SHORTED TO GROUND
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Note: It may be necessary to remove the Intake Plenum in the following
step.
Disconnect the Injector #6 Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #6.
Is the resistance between 10.0 and 16.0 ohms?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
97
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Note: It may be necessary to remove the Intake Plenum in the following
step.
Disconnect the Injector #6 Connector.
Note: Check connectors - Clean/repair as necessary.
Turn ignition on.
With the DRB, actuate the ASD Relay.
Using a Voltmeter, measure the ASD Relay Output voltage.
Does the voltage cycle high and low?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 4
No®Repair the open Auto Shutdown Relay Output Circuit.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Note: It may be necessary to remove the Intake Plenum in the following
step.
Disconnect the Injector #6 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #6 Driver Circuit from the PCM to the
Injector.
Is the resistance below 5.0 ohms?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 5
No®Repair the open Injector #6 Driver Circuit.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off
Note: It may be necessary to remove the Intake Plenum in the following
step.
Disconnect the Injector #6 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #6 Driver Circuit to ground.
Is the resistance below 5.0 ohms?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair the Injector #6 Driver Circuit for a short to ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 It there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-5A.
98
DRIVEABILITY
P-0206 INJECTOR #6 CONTROL CIRCUIT ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
7 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 8
8 Engine Running
Wiggle Wiring Harness from the Injector to the PCM.
Does the engine miss or stall?ENGINE - 3.0L,
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair as necessary where wiggling caused the problem to
appear.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
99
DRIVEABILITY
P-0206 INJECTOR #6 CONTROL CIRCUIT ÐContinued
ProCarManuals.com

Symptom List:
P-0300 MULTIPLE CYLINDER MIS-FIRE
P-0301 CYLINDER #1 MIS-FIRE
P-0302 CYLINDER #2 MIS-FIRE
P-0303 CYLINDER #3 MIS-FIRE
P-0304 CYLINDER #4 MIS-FIRE
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P-0300 MULTIPLE CYLINDER
MIS-FIRE.
When Monitored and Set Condition:
P-0300 MULTIPLE CYLINDER MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0301 CYLINDER #1 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0302 CYLINDER #2 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0303 CYLINDER #3 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0304 CYLINDER #4 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
100
DRIVEABILITY
ProCarManuals.com