2000 CHRYSLER CARAVAN engine

TEST SC-1ACONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-1A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
USING THE SCHEMATIC
AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1
NO
CHECK THE BRAKE LAMP ARE THE BRAKE LAMP
SWITCH AND CLUTCH SWITCH AND CLUTCH NO ADJUST OR REPLACE
PEDAL SWITCH PEDAL SWITCH AS NECESSARY.*
ADJUSTMENTS. ADJUSTED CORRECTLY?
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
375
ProCarManuals.com

TEST SC-2ACHECKING SPEED CONTROL OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
KEY OFF.
START TEST DISCONNECT THE
SC-2A. CLOCKSPRING
HARNESS
CONNECTOR.**
KEY ON. USING THE A JUMPER WIRE DID THE VOLTAGE
DRB, MONITOR THE ACROSS CLOCKSPRING CHANGE FROM YES REPLACE THE SPEED
CRUISE SWITCH HARNESS CONNECTOR APPROXIMATELY 5.0 CONTROL SWITCHES.*
VOLTAGE WHILE CAVITIES 3 AND 4. VOLTS TO 0 VOLTS?
CONNECTING... FIG.1
NO
KEY ON. PROBE THE REPAIR THE OPEN
USE A VOLTMETER IN CLOCKSPRING IS THE VOLTAGE YES SPEED CONTROL
THE FOLLOWING HARNESS CONNECTOR ABOVE 4.0 VOLTS? SWITCH GROUND
STEP. CAVITY 4. CIRCUIT.*
NO
KEY OFF. USING AN OHMMETER,
DISCONNECT THE ECM MEASURE THE SPEED IS THE RESISTANCE YES REPAIR THE OPEN
HARNESS CONTROL SWITCH ABOVE 5.0 OHMS? SPEED CONTROL
CONNECTORS.** CIRCUIT. SWITCH CIRCUIT.*
FIG.1
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
377
ProCarManuals.com

TEST SC-3ACONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3A KEY OFF.
CONTINUED FROM
THE PREVIOUS DISCONNECT THE BRAKE
PAGE. LAMP SWITCH HARNESS
CONNECTOR.**
USING A VOLTMETER, REPAIR THE BRAKE
PROBE BRAKE LAMP IS THE VOLTAGE NO LAMP SWITCH FUSED
SWITCH HARNESS ABOVE 9.0 VOLTS? BATTERY SUPPLY
CONNECTOR CAVITY 6. CIRCUIT FOR AN
FIG.1 OPEN.*
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN BRAKE LAMP DISPLAY CHANGE YES ADJUST OR REPLACE
SWITCH HARNESS TURN IGNITION ON. FROM "RELEASED" TO THE BRAKE LAMP
CONNECTOR CAVITIES "PRESSED"? SWITCH.*
5 AND 6. FIG.1
NO
REMOVE THE JUMPER. AT THE BRAKE LAMP REPAIR THE PRIMARY
USING A VOLTMETER, SWITCH HARNESS IS THE VOLTAGE NO BRAKE SWITCH
MEASURE THE CONNECTOR CAVITY 5. BELOW 1.0 VOLT? SIGNAL CIRCUIT FOR
PRIMARY SWITCH A SHORT TO
SIGNAL CIRCUIT... FIG.1 VOLTAGE.*
YES
KEY OFF. USING AN OHMMETER, REPAIR THE PRIMARY
MEASURE RESISTANCE IS THE RESISTANCE NO BRAKE SWITCH
DISCONNECT THE ECM OF THE PRIMARY BRAKE BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
HARNESS SW SIGNAL CKT. AN OPEN.*
CONNECTORS.** FIG.2
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
381
ProCarManuals.com

TEST SC-3BCHECKING SPEED CONTROL OPERATION
Perform TEST SC-3A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST
SC-3B. TURN IGNITION OFF.
DISCONNECT THE KEY ON. USING A
BRAKE LAMP SWITCH VOLTMETER, MEASURE IS THE VOLTAGE NO CONTINUE TEST
HARNESS VOLTAGE AT CAVITY 1. ABOVE 9.0 VOLTS? SC-3B ON THE
CONNECTOR.** NEXT PAGE.
FIG.1
YES
USING A JUMPER WHILE MONITORING DID THE DRB
WIRE, CONNECT THE DRB. DISPLAY CHANGE YES ADJUST OR REPLACE
BRAKE LAMP SWITCH FROM "PRESSED" TO THE BRAKE LAMP
CONNECTOR CAVITY 1 "RELEASED"? SWITCH.*
TO GROUND... FIG.1
NO
USING AN OHMMETER,REPAIR THE OPEN
MEASURE THE IS THE RESISTANCE YES SECONDARY BRAKE
RESISTANCE BETWEEN ABOVE 10.0 OHMS? LAMP SWITCH GROUND
CONNECTOR CAVITY 2CIRCUIT.*
AND GROUND. FIG.1
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
383
ProCarManuals.com

TEST SC-3BCONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3B
CONTINUED FROM DISCONNECT THE ECM
THE PREVIOUS TURN IGNITION OFF. HARNESS
PAGE. CONNECTORS.**
OF THE SECONDARY REPAIR OPEN IN THE
USING AN OHMMETER, BRAKE LAMP SWITCH IS THE RESISTANCE NO SECONDARY BRAKE
MEASURE THE SIGNAL CIRCUIT. BELOW 5.0 OHMS? LAMP SWITCH SIGNAL
RESISTANCE...CIRCUIT.*
FIG.1
YES
THE BRAKE LAMP REPAIR SHORT TO
USING AN OHMMETER, SWITCH CONNECTOR IS THE RESISTANCE YES GROUND IN THE
MEASURE RESISTANCE CAVITY 1 AND GROUND. BELOW 5.0 OHMS? SECONDARY BRAKE
BETWEEN... LAMP SWITCH SIGNAL
FIG.2 CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
385
ProCarManuals.com

TEST SC-4ACHECKING SPEED CONTROL OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST
SC-4A. TURN IGNITION OFF.
DISCONNECT THE USING AN OHMMETER, REPAIR OPEN IN
CLUTCH PEDAL MEASURE RESISTANCE IS THE RESISTANCE NO CLUTCH PEDAL
SWITCH HARNESS BETWEEN CLUTCH PEDAL BELOW 5.0 OHMS? SWITCH GROUND
CONNECTOR.** SW.CONNECTOR CAVITY CIRCUIT.*
2 AND GROUND. FIG.1
YES
KEY ON. WHILE THE CLUTCH PEDAL CHECK ADJUSTMENT OF
OBSERVING THE DRB, SWITCH HARNESS DID THE DRB CHANGE YES CLUTCH PEDAL SWITCH.
CONNECT A JUMPER CONNECTOR CAVITIES FROM "RELEASED" TO IF ADJUSTMENT IS OK,
WIRE ACROSS... 1 AND 2. "PRESSED"? REPLACE THE CLUTCH
FIG.1 PEDAL SWITCH.*
NO
KEY OFF. USING AN OHMMETER,
DISCONNECT THE ECM MEASURE THE IS THE RESISTANCE NO REPAIR OPEN CLUTCH
HARNESS RESISTANCE OF THE BELOW 5.0 OHMS? PEDAL SWITCH SENSE
CONNECTORS.** CLUTCH PEDAL SWITCH CIRCUIT.*
CIRCUIT. FIG.2
YES
ECM HARNESS REPAIR CLUTCH
USING AN OHMMETER CONNECTOR CAVITY IS THE RESISTANCE NO PEDAL SWITCH SENSE
MEASURE RESISTANCE 46 AND GROUND. ABOVE 5.0 OHMS? CIRCUIT FOR SHORT
BETWEEN... TO GROUND.*
FIG. 1
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
387
ProCarManuals.com

TEST SC-5ACHECKING SPEED CONTROL OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST TEST DRIVE THE DOES THE NO REFER TO THE BODY
SC-5A. VEHICLE. SPEEDOMETER DIAGNOSTIC
OPERATE CORRECTLY. PROCEDURES MANUAL...
YES
TO DIAGNOSE
INOPERATIVE
SPEEDOMETER.
USING THE DRB,
MONITOR VEHICLE DOES THE DRB YES REPLACE THE ENGINE
SPEED WHILE TEST DISPLAY CORRECT CONTROL MODULE.*
DRIVING THE VEHICLE SPEED?
VEHICLE
NO
PERFORM TEST
TC-91A.
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
389
ProCarManuals.com

TEST SC-6ACHECKING CRUISE INDICATOR OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
NOTE: PERFORM TEST
START TEST SC-1A TO VERIFY
SC-6A. PROPER CRUISE
SWITCH OPERATION
BEFORE CONTINUING.
TURN IGNITION ON. MONITOR CRUISE DOES LAMP STATE CHECK CRUISE LAMP
WITH THE DRB SELECT LAMP STATE WHILE CHANGE FROM "ON" YES BULB, REPLACE AS
"BODY" "MIC" PRESSING CRUISE TO "OFF" WHEN NECESSARY. IF OK,
"MONITOR DISPLAY" ON/OFF BUTTON PRESSING THE REPLACE THE
THEN "CCD BUS INFO". SEVERAL TIMES. BUTTON? INSTRUMENT CLUSTER.*
NO
KEY OFF. KEY ON. CONNECT A
DISCONNECT THE ECM JUMPER WIRE BETWEEN IS THE SPEED YES REPLACE THE ENGINE
HARNESS ECM HARNESS CONTROL LAMP ON? CONTROL MODULE.*
CONNECTORS.** CONNECTOR CAVITY 30
AND GROUND. FIG.1
NO
KEY OFF. USING AN OHMMETER, REPAIR SHORT TO
DISCONNECT THE BCM MEASURE RESISTANCE IS THE RESISTANCE YES GROUND ON THE
HARNESS BETWEEN ECM HARNESS BELOW 5.0 OHMS? SPEED CONTROL LAMP
CONNECTORS.** CONNECTOR CAVITY 30 CONTROL CIRCUIT.*
AND GROUND. FIG.1
NO
USING AN OHMMETER
MEASURE THE SPEED IS THE RESISTANCE YES REPAIR OPEN SPEED
CONTROL LAMP ABOVE 5.0 OHMS? CONTROL LAMP
CONTROL CIRCUIT. CONTROL CIRCUIT.*
FIG.2
NO
REPLACE THE BODY
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
391
ProCarManuals.com