2000 CHRYSLER CARAVAN check engine

TEST NS-1AREPAIRING A NO CRANK CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
NOTE: BATTERY MUST
START TEST BE FULLY CHARGED
NS-1A. BEFORE DIAGNOSING
A NO-START
CONDITION.
NOTE: BEFORE VEHICLE THEFT DIAGNOSE
CONTINUING, BE (SKIM) SYSTEM FOR ARE ANY CODES YES TROUBLE CODE
SURE TO CHECK DIAGNOSTIC TROUBLE PRESENT? BEFORE
ENGINE SYSTEM CODES. CONTINUING.]
AND...
NO
INSPECT BATTERY
CABLES FOR IS THERE EVIDENCE YES REPAIR AS
TURN IGNITION OFF. CORROSION, OF PROBLEMS? NECESSARY.*
LOOSENESS OR OTHER
PROBLEMS.
NO
TURN IGNITION OFF. KEY ON. WITH A REPAIR THE STARTER
VOLTMETER, MEASURE IS THE VOLTAGE YES RELAY CONTROL
DISCONNECT THE ECM THE STARTER RELAY ABOVE 1.0 VOLT? CIRCUIT FOR A
HARNESS CONTROL CKT. SHORT TO VOLTAGE.*
CONNECTORS.** FIG.1
NO
KEY OFF. USING A FULLY DEPRESS THE
JUMPER WIRE CONNECT CLUTCH PEDAL. DID THE ENGINE YES REPLACE THE ENGINE
THE STARTER RELAY CRANK? CONTROL MODULE.*
CONTROL CKT TO ATTEMPT TO CRANK
GROUND. FIG.1 THE ENGINE.
NO
WITH A VOLTMETER,
DISCONNECT THE MEASURE THE FUSED IS THE VOLTAGE NO REPAIR OPEN FUSED
STARTER RELAY FROM B(+) CIRCUIT. ABOVE 11.6 VOLTS? BATTERY CIRCUIT.*
THE PDC.**
FIG.1
YES
WARNING: THE TRANS WARNING: THE ENGINE BRIEFLY CONNECT A
MUST BE IN NEUTRAL MAY BE CRANKED IN JUMPER WIRE BETWEEN CONTINUE TEST
AND THE PARKING THE NEXT STEP. KEEP THE STARTER RLY NS-1A ON THE
BRAKE MUST BE ON AWAY FROM MOVING OUTPUT AND FUSED NEXT PAGE.
FOR THE NEXT STEP. ENGINE PARTS. B(+) CKTS. FIG.1
N
O
S
T
A
R
T
T
E
S
T
S
395
ProCarManuals.com

TEST NS-1ACONTINUED - REPAIRING A NO CRANK CONDITION
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-1A
CONTINUED FROM DID THE STARTER YES CONTINUE TEST
THE PREVIOUS MOTOR CRANK THE NS-1A ON THE
PAGE. ENGINE? NEXT PAGE.
NO
DID THE STARTER
YES SOLENOID CLICK NO DISCONNECT THE
WHEN THE JUMPER JUMPER WIRE.
WIRE WAS
CONNECTED?
USING AN OHMMETER, DISCONNECT STARTER
MEASURE THE RELAY OUTPUT WIRE
STARTER RELAY FROM THE STARTER
OUTPUT CIRCUIT. SOLENOID.**
FIG.1 FIG.2
IS THE RESISTANCE NO REPAIR OPEN
BELOW 5.0 OHMS? STARTER RELAY
OUTPUT CKT.*
YES
CHECK THE BATTERY DID EITHER BATTERY
REINSTALL STARTER CABLES FOR HIGH CIRCUIT HAVE A YES REPAIR THE BATTERY
RELAY. RESISTANCE. (USE VOLTAGE DROP CIRCUIT FOR HIGH
SERVICE MANUAL GREATER THAN 0.2 RESISTANCE.*
PROCEDURE) VOLT?
NO
ATTEMPT TO
MANUALLY ROTATE IS THE CRANKSHAFT NO REPAIR ENGINE
THE CRANKSHAFT 360 ABLE TO ROTATE 360 MECHANICAL PROBLEM
DEGREES. DEGREES? AS NECESSARY.*
YES
REPLACE THE
STARTER MOTOR.*
N
O
S
T
A
R
T
T
E
S
T
S
397
ProCarManuals.com

TEST NS-2AREPAIRING A NO RESPONSE CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
START TEST DOES THE VEHICLE YES PERFORM TEST
NS-2A. START? NS-2B.
NO
KEY OFF. WITH AN OHMMETER, IS THE RESISTANCE
MEASURE RESISTANCE ABOVE 5.0 OHMS FOR YES REPAIR THE OPEN
DISCONNECT THE ECM OF THE PCM GND CKTS ANY OF THE ECM GROUND.*
HARNESS AT HARNESS CAVITIES MEASUREMENTS?
CONNECTORS.** 1 AND 27. FIG.1
NO
KEY ON. USING A AT ECM HARNESS REPAIR OPEN OR
VOLTMETER, MEASURE CONNECTOR CAVITY 47. IS THE VOLTAGE NO SHORT TO GROUND IN
THE FUSED IGNITION ABOVE 10.0 VOLTS? THE FUSED IGNITION
SWITCH OUTPUT SWITCH OUTPUT
CIRCUIT... FIG.1 CIRCUIT.*
YES
KEY OFF. USING A VOLTMETER REPAIR OPEN FUSE
REMOVE THE DIESEL PROBE DIESEL POWER IS THE VOLTAGE NO OR FUSED BATTERY
POWER RELAY. RELAY CONNECTOR ABOVE 10.0 VOLTS? CIRCUIT TO DIESEL
CAVITY 30 (IN PDC). POWER RELAY.*
KEY ON. FIG.2
YES
KEY OFF. CONNECT A MEASURE VOLTAGE AT IS THE VOLTAGE
JUMPER WIRE ACROSS ECM HARNESS ABOVE 10.0 VOLTS NO REPAIR OPEN DIESEL
RELAY CONNECTOR CONNECTOR CAVITIES FOR EACH POWER RELAY OUTPUT
CAVATIES 30 AND 87. 2 AND 28. MEASUREMENT? CIRCUIT(S).*
FIG. 1 AND 2
YES
KEY OFF. RECONNECT WITH JUMPER WIRE
THE ENGINE CONTROL STILL CONNECTED, DOES THE VEHICLE NO REPLACE THE ENGINE
MODULE HARNESS ATTEMPT TO START START? CONTROL MODULE.*
CONNECTORS. VEHICLE.
YES
CONTINUE TEST
NS-2A ON THE
NEXT PAGE.
N
O
R
E
S
P
O
N
S
E
T
E
S
T
401
ProCarManuals.com

TEST NS-2BCONTINUED - REPAIRING A NO RESPONSE CONDITION
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-2B CONNECT THE DRB TO
CONTINUED FROM A FUNCTIONAL DATA
THE PREVIOUS LINK ON ANOTHER
PAGE. VEHICLE.
REPLACE THE
WITH THE DRB, DID THE DRB NO INITIAL VEHICLE'S
TURN IGNITION ON. ATTEMPT TO READ DISPLAY "NO ENGINE CONTROL
TROUBLE CODES. RESPONSE"? MODULE.*
YES
SUBSTITUTE ANOTHER WITH THE DRB, DID THE DRB NO REPLACE THE DRB
DRB ADAPTER CABLE. ATTEMPT TO READ DISPLAY "NO ADAPTER CABLE.*
TROUBLE CODES. RESPONSE"?
YES
HAVE THE DRB
REPAIRED OR
REPLACED.*
N
O
R
E
S
P
O
N
S
E
T
E
S
T
409
ProCarManuals.com

TEST NS-3BREPAIRING - NO START
Perform TEST NS-3A Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
START TEST
NS-3B. TURN IGNITION OFF.
DISCONNECT THE
DISCONNECT THE ECM BODY CONTROL
HARNESS MODULE HARNESS
CONNECTORS.** CONNECTORS.**
USING AN OHMMETER,
MEASURE RESISTANCE IS THE RESISTANCE YES REPAIR THE OPEN
OF THE IMMOBILIZER ABOVE 5.0 OHMS? IMMOBILIZER SIGNAL
SIGNAL CIRCUIT. CIRCUIT.*
FIG.1
NO
ENGINE CONTROL REPAIR THE
MEASURE RESISTANCE MODULE HARNESS IS THE RESISTANCE YES IMMOBILIZER SIGNAL
BETWEEN ... CONNECTOR CAVITY BELOW 5.0 OHMS? CIRCUIT FOR A
38 AND GROUND. SHORT TO GROUND.*
FIG. 1
NO
USING A VOLTMETER, REPAIR THE
MEASURE VOLTAGE AT IS THE VOLTAGE YES IMMOBILIZER SIGNAL
TURN IGNITION ON. ECM HARNESS ABOVE 1.0 VOLT? CIRCUIT FOR A
CONNECTOR CAVITY 38. SHORT TO VOLTAGE.*
FIG. 1
NO
CONTINUE TEST
NS-3B ON THE
NEXT PAGE.
N
O
S
T
A
R
T
T
E
S
T
S
415
ProCarManuals.com

TEST NS-3BCONTINUED - REPAIRING - NO START
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-3B TURN IGNITION OFF.
CONTINUED FROM RECONNECT THE
THE PREVIOUS ENGINE CONTROL
PAGE. MODULE HARNESS
CONNECTORS.
KEY ON. MEASURE
USE AN AMMETER IN AMPERAGE FROM BCM IS THE AMPERAGE NO REPLACE THE ENGINE
THE FOLLOWING HARNESS CONNECTOR BETWEEN 1.0 AND CONTROL MODULE.*
STEP. CAVITY 72 TO GROUND. 1.4 MA?
FIG.1
YES
RECONNECT THE BODY USING THE DRB
CONTROL MODULE OSCILLOSCOPE
HARNESS FUNCTION, SELECT
CONNECTORS. "LAB SCOPE".
SET VOLTAGE RANGE TO KEY ON. USING
+20.0V. SET TIME OSCILLOSCOPE LEAD,
RANGE TO 0.1S/DIV. BACKPROBE ECM
SET PROBE TO X10. HARNESS CONNECTOR
FIG.2 CAVITY 38. FIG.1
NOTE: AN IMMOBILIZER DOES THE DRB DISPLAY
SIGNAL WILL CYCLE HI SHOW THE 12 VOLT YES REPLACE THE ENGINE
TO LO SIMILAR TO THE IMMOBILIZER SIGNAL CONTROL MODULE.*
PATTERN SHOWN IN CYCLING HI AND LO?
FIG.2 FIG.2
NO
REPLACE THE BODY
CONTROL MODULE.*
N
O
S
T
A
R
T
T
E
S
T
S
417
ProCarManuals.com

TEST NS-4AREPAIRING A START AND STALL CONDITION
Perform TEST NS-SEL Before Proceeding
At this point in the diagnostic test procedure it is assumed that all of the engine electrical systems
are operating as designed and are not the cause of a start and stall, or a no start problem. The
following additional items should be checked as possible mechanical problems. Any one of these
items can produce a start and stall, or no start condition; none can be overlooked as a possible
cause.
1. ENGINE VALVE TIMINGÐ must be within specifications
2. ENGINE COMPRESSIONÐ must be within specifications
3. ENGINE EXHAUST SYSTEMÐ must be free of any restrictions
4. FUELÐ must be free of contamination
5. FUEL FILTERÐ must be free of any restrictions
6. INTAKE AIR DUCTÐ passages must be free of any debris
Always look for any Technical Service Bulletins that may relate to this problem.
N
O
S
T
A
R
T
T
E
S
T
S
418
ProCarManuals.com

TEST NS-5ACHECKING THE ENGINE MECHANICAL SYSTEMS
Perform TEST NS-SEL Before Proceeding
NOTES
N
O
S
T
A
R
T
T
E
S
T
S
420
ProCarManuals.com