2000 Acura RL coolant level

Gauge
s

Outside Temperature Indicator
This indicator displays the outside temperature in Fahrenheit in U.S.
models, and in Centigrade inCanadian models.
The temperature sensor is located in the front bumper. Therefore, the
temperature reading can be affected
by heat reflection from the road sur-
face, engine heat, and the exhaust
from the surrounding traffic. This can cause the temperature reading
not to be correct when your speed is
under 19 mph (30 km/h).
In certain weather conditions,
temperature readings near freezing (32°F, 0°C) could mean that ice is
forming on the road surface. Temperatur
e Gaug e
This shows the temperature of the engine's coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe driving conditions, such as very hot
weather or a long period of uphill driving, the pointer may rise to near
the upper white mark. If it reaches
the red (Hot) mark, pull safely to the side of the road. Turn to page 280 for
instructions and precautions on checking the engine's cooling

system.
Fue
l Gaug e
This shows how much fuel you have. It is most accurate when the car is on
level ground. It may show slightly more or less than the actual amount
when you are driving on curvy or hilly roads.
The gauge stays at the same fuel level reading after you turn off theignition. When you add fuel, the
gauge slowly changes to the new
reading after you turn the ignitionswitch back ON (II).
Instrument s an d Control s

Before
Driving
Before you begin driving your Acura,
you should know what gasoline to use, and how to check the levels of
important fluids. You also need to
know how to properly store luggage or packages. The information in this
section will help you. If you plan to
add any accessories to your car,
please read the information in this section first. Break-in Period.............................. 166
Gasoline.......................................... 166
Service Station Procedures .......... 167 Filling the Fuel Tank................. 167Opening the Hood..................... 168
Oil Check................................ 169
Engine Coolant Check.......... 170
Fuel Economy................................ 171 Car Condition............................. 171
Driving Habits............................ 171
Accessories and Modifications.... 172 Carrying Cargo.............................. 174

Before Drivin g

Servic
e Statio n Procedure s

3. Insert it all the way back in its tube.

4. Remove the dipstick again and
check the level. It should be
between the upper and lower marks.

If it is near or below the lower mark,
see Addin g Oi l on page 215 . Engine Coolant Check
Look at the coolant level in the
radiator reserve tank. Make sure it is
between the MAX and MIN lines. If
it is below the MIN line, see Addin g
Engin e Coolan t on page 219 for
information on adding the proper

coolant.

Refer to Owne r Maintenanc e
Check s on page 213 for information
on checking other items in your
Acura.
Befor e Drivin g
RESERV
E TAN K

UPPE R MAR K
LOWE R MAR K
MA
X
MI N

Owne
r Maintenanc e Check s
You should check the following items at the specified intervals. If
you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every
time you fill the fuel tank. See
page 169.
Engine coolant level — Check the
radiator reserve tank every time
you fill the fuel tank. See page 170.

Windshield washer fluid — Check the level in the reservoir monthly.If weather conditions cause you to
use the washers frequently, check
the reservoir each time you stop
for fuel. See page 225 . Automatic transmission — Check
the fluid level monthly. See page
226.
Brakes — Check the fluid level
monthly. See page 22 8 . Tires —
Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See page
241.
Lights — Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and license plate lights monthly. See

page 248.

Maintenance

Coolin
g Syste m
Addin g Engin e Coolan t
If the coolant level in the reserve
tank is at or below the MIN line, add coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and
50 percent water. Never add straight
antifreeze or plain water. Always use Genuine Honda
Antifreeze/Coolant. If it is not
available, you may use another
major-brand non-silicate coolant as a
temporary replacement. Make sure it is a high-quality coolant
recommended for aluminum engines.However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling system to malfunction or fail. Have
the cooling system flushed and
refilled with Honda antifreeze/
coolant as soon as possible. If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
1. Make sure the engine and radiator
are cool.

CONTINUED

Maintenanc e

RESERV
E TAN K
Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Coolin
g Syste m

2. Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.

3. Remove the radiator cap by

pushing down and turning
counterclockwise.

4. The coolant level should be up to

the base of the filler neck. Add
coolant if it is low.

5. Put the radiator cap back on.

Tighten it fully.

6. Pour coolant into the reserve tank.

Fill it to halfway between the MAX
and MIN marks. Put the cap back
on the reserve tank.

Do not add any rust inhibitors or
other additives to your car's cooling
system. They may not be compatible
with the coolant or engine compo-
nents.

Maintenanc e
RADIATO
R CA P
RESERVE TAN K

Coolin
g Syste m

8. Remove the two bolts and the three nuts with a 7/16 in (10 mm)
wrench, then remove the enginecover. 9. Loosen the bleeder bolt on top of
the engine.
Pour coolant into the radiator up to the base of the filler neck.
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles. 10.Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
11.Check the level in the radiator, add coolant if needed.

CONTINUED

Maintenanc e

NUT
S

BOLT S
BLEEDE
R BOL T
Fill u p t o her e

FILLE
R NEC K

Cooling
Syste m

12.Install the engine cover. First tighten the two bolts on the frontof the engine cover, then tighten
the three nuts on the engine cover.

Tightening torque:
7 lbf .
ft (10 N .
m,1.0 kgf.m)

13.Install the radiator cap, and

tighten it to the first stop.
14.Start the engine and let it run until the radiator cooling fan comes onat least twice. Then stop the

engine.
15.Remove the radiator cap. Pour
coolant into the radiator up to the
base of the filler neck and into the
reserve tank up to the MAX mark.
16.Start the engine and hold it at 1,500 rpm until the cooling fancomes on. Turn off the engine.Check the coolant level in the
radiator and add coolant if needed.
17.Install the radiator cap, and tighten it fully.
18. If necessary, fill the reserve tank

to the MAX mark. Install the
reserve tank cap.

Maintenanc e
RESERV
E TAN K