1999 YAMAHA YZF-R7 oil level

3 - 2
CHK
ADJ

PERIODIC MAINTENANCE AND LUBRICATION
INTERVALS
*
Since these items require special tools, data and technical skills, they should be serviced by a
Yamaha dealer.
NOTE:

• The air filter element needs more frequent service if you are riding in unusually wet or
dusty areas.
• Hydraulic brake system
– Replace the brake fluid or clutch fluid after disassembling the master cylinder, caliper cyl-
inder or release cylinder.
– Check the brake fluid or clutch fluid level and add fluid as required.
– Replace the master cylinder, caliper cylinder and release cylinder oil seals every two
years.
– Replace the brake hoses and clutch hose every four years, or if cracked or damaged.
15
*
Chassis fasteners
• Make sure that all nuts, bolts and screws are properly
tightened.
• Tighten if necessary.
ÖÖ
16 Sidestand
• Check operation.
• Lubricate and repair if necessary.
ÖÖ
17
*
Sidestand switch
• Check operation.
• Replace if necessary.
ÖÖÖ
18
*
Front fork
• Check operation and for oil leakage.
• Correct accordingly.
ÖÖ
19
*
Rear shock
absorber assembly
• Check operation and shock absorber for oil leakage.
• Replace shock absorber assembly if necessary.
ÖÖ
20
*
Rear suspension
relay arm and con-
necting arm pivot-
ing points
• Check operation.
• Lubricate with lithium soap base grease every 24,000
km or 24 months (whichever comes first).
ÖÖ
21
*
Electronic fuel
injection system
• Check engine idling speed, synchronization and
starter operation.
• Adjust if necessary.
ÖÖÖ
22 Engine oil
• Check oil level and vehicle for oil leakage.
• Correct if necessary.
• Change. (Warm engine before draining.)
ÖÖÖ
23Engine oil filter
cartridge
• Replace.
ÖÖ
24
*
Cooling system
• Check coolant level and vehicle for coolant leakage.
• Correct if necessary.
• Change coolant every 24,000 km 24 months (which-
ever comes first).
ÖÖ
No. ITEM CHECKS AND MAINTENANCE JOBSINITIAL
1,000 km EVERY
6,000 km or
6 months
(whichever
comes first)12,000 km or
12 months
(whichever
comes first)
3

3 - 21
CHK
ADJ
MEASURING THE COMPRESSION PRESSURE
3. Remove:
• fuel tank
• air filter case cover
Refer to “FUEL TANK AND AIR FIL-
TER”.
• air filter case
• throttle body assembly
Refer to “ELECTRONIC FUEL INJEC-
TION” in chapter 6.
• ignition coil
4. Remove:
• spark plug
ACHTUNG:CAUTION:
Before removing the spark plugs, use
compressed air to blow away any dirt
accumulated in the spark plug wells to
prevent it from falling into the cylinders.
5. Install:
• compression gauge 1
• adapter 2
Compression gauge
90890-03081
Adapter
90890-04136
1
1

2

2

6. Measure:
• compression pressure
Out of specification ® Refer to steps
(c) and (d).
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Set the main switch to “ON”.
b. With the throttle wide open, crank the
engine until the reading on the com-
pression gauge stabilizes.
Compression pressure (at sea
level)
Minimum
1,500 kPa
(15.0 kg/cm
2, 213 psi)
Standard
1,600 kPa
(16.0 kg/cm
2, 228 psi)
Maximum
1,700 kPa
(17.0 kg/cm
2, 242 psi)

3 - 23
CHK
ADJ
CHECKING THE ENGINE OIL LEVEL
EB303070
CHECKING THE ENGINE OIL LEVEL
1. Stand the motorcycle on a level surface.
NOTE:
• Place the motorcycle on a suitable stand.
• Make sure that the motorcycle is
upright.
2. Start the engine, let it idle for several
minutes, and then stop it.
3. Check:
• engine oil level
The engine oil level should be between
the minimum level mark a and maxi-
mum level mark b.
Below the minimum level mark ® Add
the recommended engine oil to the
proper level.
Recommended oil
Refer to the chart for the
engine oil grade which is best
suited for certain atmo-
spheric temperatures.
API standard
SE or higher grade
(Non-Friction modified)
ACHTUNG:CAUTION:
• Engine oil also lubricates the clutch
and the wrong oil types or additives
could cause clutch slippage. There-
fore, do not add any chemical addi-
tives or use engine oils with a grade of
CD c or higher and do not use oils
labeled “ENERGY CONSERVING II” d
or higher.
• Do not allow foreign materials to
enter the crankcase.
4. Start the engine, warm it up for several
minutes, and then turn it off.
5. Check:
• engine oil level
NOTE:
Before checking the engine oil level,
wait a few minutes until the oil has set-
tled.

3 - 25
CHK
ADJ
CHANGING THE ENGINE OIL
9. Fill:
• crankcase
(with the specified amount of the rec-
ommended engine oil)
10.Install:
• engine oil filler cap
11.Start the engine, warm it up for several
minutes, and then turn it off.
12.Check:
• engine
(for engine oil leaks)
13.Check:
• engine oil level
Refer to “CHECKING THE ENGINE OIL
LEVEL”.
Quantity
Total amount
3.6 L (3.2 lmp qt, 3.8 US qt)
Without oil filter cartridge
replacement
2.6 L (2.3 lmp qt, 2.7 US qt)
With oil filter cartridge
replacement
2.8 L (2.5 lmp qt, 3.0 US qt)
14.Check:
• engine oil pressure
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Slightly loosen the oil gallery bolt 1.
b. Start the engine and keep it idling
until engine oil starts to seep from the
oil gallery bolt. If no engine oil comes
out after one minute, turn the engine
off so that it will not seize.
c. Check the engine oil passages, the oil
filter cartridge and the oil pump for
damage or leakage. Refer to “OIL
PAN AND OIL PUMP” in chapter 4.
d. Start the engine after solving the
problem(-s) and check the engine oil
pressure again.
e. Tighten the oil gallery bolt to
specification.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
T R..
Oil gallery bolt
20 Nm (2.0 m • kg, 14 ft • lb)
1
1

3 - 26
CHK
ADJCHANGING THE ENGINE OIL/
CHECKING THE CLUTCH FLUID LEVEL
15.Install:
• front cowling
• bottom cowling
Refer to “COWLINGS”.
EB303100
CHECKING THE CLUTCH FLUID LEVEL
1. Stand the motorcycle on a level surface.
NOTE:
• Place the motorcycle on a suitable
stand.
• Make sure that the motorcycle is
upright.
2. Check:
• clutch fluid level
Below the minimum level mark a ®
Add the recommended clutch fluid to
the proper level.
WARNINGWARNING
• Use only the designated clutch fluid.
Other fluids may cause the rubber
seals to deteriorate, causing leakage
and poor clutch performance.
• Refill with the same type of fluid. Mix-
ing fluids may result in a harmful
chemical reaction leading to poor
clutch performance.
• When refilling, be careful that water
does not enter the clutch fluid reser-
voir. Water will significantly lower the
boiling point of the fluid and could
cause vapor lock.
ACHTUNG:CAUTION:
Clutch fluid may damage painted sur-
faces and plastic parts. Always clean up
any split fluid immediately.
NOTE:
In order to ensure a correct reading of
the clutch fluid level, make sure that the
top of the clutch fluid reservoir is hori-
zontal.
Recommended clutch fluid
Brake fluid DOT 4aa

3 - 37
CHK
ADJADJUSTING THE REAR BRAKE/
CHECKING THE BRAKE FLUID LEVEL
ACHTUNG:CAUTION:
After adjusting the brake pedal position,
make sure that there is no brake drag.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
3. Adjust:
• rear brake light switch
Refer to “ADJUSTING THE REAR
BRAKE LIGHT SWITCH”.
EB304020
CHECKING THE BRAKE FLUID LEVEL
1. Stand the motorcycle on a level surface.
NOTE:
• Place the motorcycle on a suitable
stand.
• Make sure that the motorcycle is
upright.
2. Check:
• brake fluid level
Below the minimum level mark a ®
Add the recommended brake fluid to
the proper level.
Front brake
õRear brake
WARNINGWARNING
• Use only the designated brake fluid.
Other brake fluids may cause the rub-
ber seals to deteriorate, causing leak-
age and poor brake performance.
• Refill with the same type of brake fluid
that is already in the system. Mixing
brake fluids may result in a harmful
chemical reaction, leading to poor
brake performance.
• When refilling, be careful that water
does not enter the brake fluid reser-
voir. Water will significantly lower the
boiling point of the brake fluid and
could cause vapor lock.
ACHTUNG:CAUTION:
Brake fluid may damage painted sur-
faces and plastic parts. Therefore,
always clean up any spilt brake fluid
immediately.
NOTE:
In order to ensure a correct reading of the
brake fluid level, make sure that the top of
the brake fluid reservoir is horizontal.
Recommended brake fluid
DOT 4

õ

3 - 43
CHK
ADJLUBRICATING THE DRIVE CHAIN/
CHECKING AND ADJUSTING THE STEERING HEAD
EB304100
LUBRICATING THE DRIVE CHAIN
The drive chain consists of many interact-
ing parts. If the drive chain is not main-
tained properly, it will wear out rapidly.
Therefore, the drive chain should be ser-
viced, especially when the motorcycle is
used in dusty areas. This motorcycle has a
drive chain with small rubber O-rings
between each side plate. Steam cleaning,
high-pressure washing, certain solvents,
and the use of a coarse brush can damage
these O-rings. Therefore, use only kerosine
to clean the drive chain. Wipe the drive
chain dry and thoroughly lubricate it with
engine oil or chain lubricant that is suitable
for O-ring chains. Do not use any other
lubricants on the drive chain since they may
contain solvents that could damage the O-
rings.
Recommended lubricant
Engine oil or chain lubricant
suitable for O-ring chains
EB304130
CHECKING AND ADJUSTING THE
STEERING HEAD
1. Stand the motorcycle on a level surface.
WARNINGWARNING
Securely support the motorcycle so that
there is no danger of it falling over.
NOTE:
Place the motorcycle on a suitable stand
so that the front wheel is elevated.
2. Check:
• steering head
Grasp the bottom of the front fork legs
and gently rock the front fork.
Looseness/binding ® Adjust the steer-
ing head.

3 - 46
CHK
ADJCHECKING AND ADJUSTING THE STEERING HEAD/
CHECKING THE FRONT FORK
d. Hold the spring gauge at a 45˚ angle
from the handlebar, pull the spring
gauge, and record the measurement
when the handlebar starts to turn.
e. Repeat the above procedure on the
opposite handlebar.
f. If the steering head tension is out of
specification (both handlebars should
be within specification), remove the
upper bracket and loosen or tighten
the upper ring nut.
g. Reinstall the upper bracket and mea-
sure the steering head tension again
as described above.
h. Repeat the above procedure until the
steering head tension is within speci-
fication.
i. Grasp the bottom of the front fork
legs and gently rock the front fork.
Looseness or binding ® Adjust the
steering head.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
Steering head tension
200 ~ 500 g (7.06 ~ 17.65 oz)
EB304141
CHECKING THE FRONT FORK
1. Stand the motorcycle on a level surface.
WARNINGWARNING
Securely support the motorcycle so that
there is no danger of it falling over.
2. Check:
• inner tube 1
Damage/scratches ® Replace.
• dust seal 2
• oil seal
Oil leakage ® Replace.
3. Hold the motorcycle upright and apply
the front brake.
4. Check:
• front fork operation
Push down hard on the handlebars
several times and check if the front
fork rebounds smoothly.
Rough movement ® Repair.
Refer to “FRONT FORK” in chapter 7.