1999 YAMAHA YZF-R7 fuses

1 - 2
DESCRIPTION
DESCRIPTION
Left view
Right view
1. Front fork compression damping force adjusting screw
2. Front fork rebound damping force adjusting screw
3. Front fork spring preload adjusting bolt
4. Air filter
5. Starter (choke) “ “
6. Shift pedal
7. Rear shock absorber spring preload adjusting ring
8. Rear shock absorber compression damping force adjusting screw
9. Rear shock absorber rebound damping force adjusting screw
10. Fuses
11. Rear brake resorvoir
12. Rear brake pedal
13. Radiator cap and coolant reservoir tank cap
14. Engine oil filter
14
56
78
9
2,3
10
11
1213 14

1

ELECTRICAL SPECIFICATIONSSPEC
2 - 16
Electric starting system
System type Constant mesh ----
Starter motor
Model (manufacturer) SM-14 (MITSUBA) ----
Power output 0.6 kW ----
Armature coil resistance 0.0015 ~ 0.0025 W----
Brushes
Overall length 10 mm (0.40 in) 3.5 mm
(0.14 in)
Spring force 7.16 ~ 9.52 N
(730 ~ 971 gf, 25.8 ~ 34.3 oz)----
Commutator resistance 0.025 ~ 0.035 W----
Commutator diameter 28 mm (1.10 in) 27 mm
(1.06 in)
Mica undercut 0.7 mm (0.03 in) ----
Starter relay
Model (manufacturer) MS5F-631 (JIDECO) ----
Amperage 180 A ----
Coil resistance 4.18 ~ 4.62 W ----
Horn
Horn type Plain ----
Model (manufacturer) ´ quantity YF-12 (NIKKO) ´ 1 ----
Max. amperage 3 A ----
Turn signal relay
Relay type Full-transistor ----
Model (manufacturer) FE246BH (DENSO) ----
Self-cancelling device built-in No ----
Turn signal blinking frequency 75 ~ 95 cycles/min. ----
Wattage 21 W ´ 2 + 3.4 W ----
Oil level switch model (manufac-
turer)071380-0480 (DENSO) ----
Fuel pump relay model (manufac-
turer)G8R-30Y-J (OMRON) ----
Thermo switch model (manufac-
turer)5EB (NIPPON THERMOSTAT) ----
Fuses (amperage ´ quantity)
Main fuse 30 A ´ 1 ----
Headlight fuse 20 A ´ 1 ----
Signaling system fuse 20 A ´ 1 ----
EFI fuse 20 A ´ 1 ----
ECU fuse 7.5 A ´ 1 ----
Radiator fan fuse 7.5 A ´ 1 ----
Backup fuse (odometer) 7.5 A ´ 1 ---- Item Standard Limit

3 - 60
CHK
ADJCHECKING AND CHARGING THE BATTERY/
CHECKING THE FUSES
6. Install:
• battery
7. Connect:
• battery leads
(to the battery terminals)
ACHTUNG:CAUTION:
First, connect the positive lead 1, then
the negative lead 2.
8. Check:
• battery terminals
Dirt ® Clean with a wire brush.
Loose connection ® Connect properly.
9. Lubricate:
• battery terminals
10.Install:
• battery band 3
• rear cowling bracket 4
• rear cowling
Refer to “COWLINGS”.
EB305040
CHECKING THE FUSES
The following procedure applies to all of
the fuses.
ACHTUNG:CAUTION:
To avoid a short circuit, always set the
main switch to “OFF” when checking or
replacing a fuse.
1. Remove:
• rear cowling
Refer to “COWLINGS”.
2. Check:
• continuity
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Connect the pocket tester to the fuse
and check the continuity.
NOTE:
Set the pocket tester selector to “W ´ 1”.
b. If the pocket tester indicates “¥”,
replace the fuse.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
Recommended lubricant
Dielectric grease
Pocket tester
90890-03112
2
2
1
1

3

3

4

4

3 - 61
CHK
ADJ
3. Replace:
• blown fuse
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Set the main switch to “OFF”.
b. Install a new fuse of the correct
amperage.
c. Set the main switch to “ON” and ver-
ify if the electrical circuit is opera-
tional.
d. If the fuse immediately blows again,
check the electrical circuit.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
WARNINGWARNING
Never use a fuse with an amperage
other than that specified. Improvising or
using a fuse with the wrong amperage
rating may cause extensive damage to
the electrical system, cause the lighting
and ignition systems to malfunction
and could possibly cause a fire.
4. Install:
• rear cowling
Refer to “COWLINGS”.Item Amperage Q’ty
Main fuse 30 A 1
Headlight
fuse20 A 1
Signaling
system fuse20 A 1
Electronic
fuel injection
system fuse20 A 1
ECU fuse 7.5 A 1
Radiator
fan motor
fuse7.5 A 1
Backup fuse
(odometer)7.5 A 1
Reserve 30 A 1
Reserve 20 A 2
Reserve 7.5 A 2
CHECKING THE FUSES

8 - 8
–+ELECIGNITION SYSTEM
TROUBLESHOOTING
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
No good
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK The ignition system fails to operate (no spark or intermittent spark).
Check the main and ECU fuses for
continuity.Replace.
Check the condition of the bat-
tery.Recharge or replace.
Check the spark plug. Re-gap or replace.
Measure the ignition spark gap. Ignition system is OK.
Measure the ignition coil resis-
tance.Replace.
Measure the pickup coil resis-
tance.Replace.
Check the main switch. Replace.
Check the engine stop switch.Replace the right handlebar
switch.
Check the neutral switch. Replace.
Check the diode. Replace.
Check the sidestand switch. Replace.
Check the relay unit. Replace.
Check the entire ignition sys-
tem’s wiring.Repair or replace.
Replace the CDI unit.
No good
No good
No good
No good
No good
No good
No good
No good
No good
OK
No good
No good
No good

8 - 13
–+ELECELECTRIC STARTING SYSTEM
TROUBLESHOOTING
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK The starter motor fails to turn.
Check the main and ECU fuses for
continuity.Replace.
Check the condition of the bat-
tery.Recharge or replace.
Check the starter motor. Repair or replace.
Check the relay unit. Replace.
Check the starter relay. Replace.
Check the diodes. Replace.
Check the main switch. Replace.
Check the engine stop switch.Replace the right handlebar
switch.
Check the neutral switch. Replace.
Check the sidestand switch. Replace.
Check the clutch switch. Replace.
Check the start switch.Replace the right handlebar
switch.
Check the entire starting sys-
tem’s wiring.Repair or replace.
No good
No good
No good
No good
No good
No good
No good
No good
No good
No good
No good
No good
No good

8 - 20
–+ELECLIGHTING SYSTEM
TROUBLESHOOTING
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
NOTE:
• Before troubleshooting, remove the following part(-s):
1) bottom cowling
2) front cowling
3) rear cowling
• Troubleshoot with the following special tool(-s).
Any of the following fail to light: headlight, high beam indicator light, taillight, auxiliary light
or meter light.
Check the main and headlight
fuses for continuity.Replace.
Check the condition of the bat-
tery.Recharge or replace.
Check the bulbs and bulb sockets. Replace.
Check the LED’s of the indicator
light.Replace the meter assembly.
Check the main switch. Replace.
Check the lights switch. Replace the left handlebar switch.
Check the dimmer switch. Replace the left handlebar switch.
Check the pass switch. Replace the left handlebar switch.
Check the entire lighting sys-
tem’s wiring.Repair or replace.
Pocket tester
90890-03112
No good
No good
No good
No good
No good
No good
No good
No good
No good

8 - 22
–+ELECSIGNALING SYSTEM
TROUBLE SHOOTING
• Any of the following fail to light: turn signal light, brake light or an indicator light.
• The horn fails to sound.
Check the main and signal system fuses
continuity.
Check the condition of the battery.
Check the main switch.
Check the entire signaling system’s wiring.
Check the bulbs and
bulb sockets.
Check the LED’s of
the indicator light.
Check the brake
switchs.
Replace the meter
assembly.
Check the neutral
switch.
Replace the meter
assembly. Check the relay unit.
Check the continuity of the thermistor in the fuel pump.OK
OK
OK
OK
OK
OK
OK
OK
OK
OKNo good
No good
No good
No goodReplace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.Recharge or replace.
Recharge or replace.
No goodNo good
No good
No good
No good
No good
No good
No good No good
No good OK
OK
BAD
OK Check the horn switch.
Check the horn. Replace.
Replace. Check the turn signal
switch.
Replace the turn
signal relay.
Replace the meter
assembly.
Replace the meter
assembly.
Replace the meter
assembly.Check the oil level
switch.
Replace the fuel
pump. Replace the left
handlebar switch.
Replace the
left handlebar
switch.