1999 SUZUKI GRAND VITARA connectors

YH4
GRAND
VITARA
7B1-76 AUTOMATIC TRANSMISSION (4 A / T)
12) Remove engine to transmission nuts.
13) Disconnect connectors from VSS, output speed sensor, input
speed sensor, TR switch, shift & TCC solenoid valves and oth-
er electrical parts, and release their wire harness from clamps.
14) Apply transmission jack and take off rear mounting member by
removing its bolts.
15) With transmission (and transfer if equipped) assembly held up
on jack, move them to the rear and lower them including torque
converter.
WARNING:
Transmission (and transfer if equipped) assembly may
tilt rearward on jack. It is recommended to use an auxil-
iary arm of jack for the purpose of safety.
AFTER DISMOUNTING
WARNING:
Be sure to keep transmission (and transfer if equipped) as-
sembly horizontal throughout the work. Should they be
tilted, torque converter may fall off and cause personal inju-
ry and A / T fluid may flow out.
1) Remove breather hoses.
2) Remove transfer by removing its bolts, if equipped.

YH4
GRAND
VITARA
8
BODY ELECTRICAL SYSTEM 8-1
SECTION 8
BODY ELECTRICAL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
WIRING SYSTEM
(Harnesses, Connectors, Fuses, Relay, Switches, Grounds, System Circuit Diagram)Section 8A . . . . . . .
LIGHTING SYSTEMSection 8B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER INFORMATIONSection 8C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WINDOWS, MIRRORS, SECURITY AND LOCKSSection 8D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMMOBILIZER CONTROL SYSTEMSection 8F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
8-2 BODY ELECTRICAL SYSTEM
GENERAL DESCRIPTION
The body electrical components of this vehicle are designed to operate on 12 Volts power supplied by the battery.
The electrical system utilizes negative ground polarity.
CAUTIONS IN SERVICING
When performing works related to electric systems, observe follow-
ing cautions for the purpose of protection of electrical parts and pre-
vention of a fire from occurrence.

When removing the battery from the vehicle or disconnecting the
cable from the battery terminals for inspection or service works
on the electric systems, always confirm first that the ignition
switch and all the other switches have been turned OFF. Other-
wise, the semi-conductor part may be damaged.

When disconnecting cables from the battery, be sure to discon-
nect the one from the negative (±) terminal first and then the other
from the positive (+) terminal.

Reverse the above order when connecting the cables to the bat-
tery terminals.

When disconnecting connectors, never pull the wiring harnesses.
Unlock the connector lock first and then pull them apart by holding
connectors themselves.

When connecting connectors, also hold connectors and put them
together until they lock securely (a click is heard).

YH4
GRAND
VITARA
8-4 BODY ELECTRICAL SYSTEM

When performing a work that produces a heat exceeding 80C
in the vicinity of the electrical parts, remove the heat sensitive
electrical part(s) beforehand.

Use care not to expose connectors and electrical parts to water
which will be a cause of a trouble.

When using a tester for checking continuity or measuring voltage,
be sure to insert the tester probe from the wire harness side.
SYMBOLS AND MARKS
Refer to Section 8A.
ABBREVIATIONS
Refer to Section 8A.

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-15
1. Main fuse
2. Main relay
3. ECM/PCM
4. Immobilizer indicator lamp
(Vehicle not equipped with
monitor coupler) For G16 / J20 engine For H25 engine
G16 / J20 Engine
H25 Engine
TABLE B IMMOBILIZER INDICATOR LAMP CHECK
(IMMOBILIZER INDICATOR LAMP DOSE NOT LIGHT AT IGNITION
SWITCH ON)
STEPACTIONYESNO
11) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter come ON?Go to Step 2.ªIGº fuse blown, main fuse blown,
ignition switch malfunction,
ªB / Wº circuit between ªIGº fuse
and combination meter or poor
coupler connection at
combination meter.
21) Turn ignition switch OFF and
disconnect connectors from ECM /
PCM.
2) Check for proper connection to ECM /
PCM at terminal E61-5 for G16 / J20
engine or E61-23 for H25 engine.
3) If OK, then using service wire, ground
terminal E61-5 for G16 / J20 engine or
E61-23 for H25 engine in connector
disconnected.
Does immobilizer indicator lamp turn on
at ignition switch ON?Substitute a known-
good ECM / PCM and
recheck.Bulb burned out or ª(b)º wire
circuit open.

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-17
DTC11 TRANSPONDER CODE NOT MATCHED
DESCRIPTION:
Immobilizer Control Module checks if Transponder code transmitted from ignition key and that registered in Immo-
bilizer Control Module match when ignition switch is ON. If they do not, this DTC is set.
INSPECTION:
Register ignition key with built-in transponder by using Suzuki scan tool (TECH1 cartridge for immobilizer control
system and TECH 1A kit) and performing following steps.
1) Register Transponder code in Immobilizer Control Module by performing procedure described in ªHow to regis-
ter ignition keyº section.
2) Turn ignition switch OFF, then turn it ON and check that DTC11 is not set.
DTC31 TRANSPONDER CODE NOT REGISTERED
DESCRIPTION:
Immobilizer Control Module checks if Transponder code transmitted from ignition key and that registered in Immo-
bilizer Control Module match when ignition switch is ON. If there is no Transponder code registered in Immobilizer
Control Module, this DTC is set.
INSPECTION:
Register ignition key with built-in transponder by using Suzuki scan tool (TECH1 cartridge for immobilizer control
system and TECH 1A kit) and performing following steps.
1) Register Transponder code in Immobilizer Control Module by performing procedure described in ªHow to regis-
ter ignition keyº section.
2) Turn ignition switch OFF, then turn it ON and check that DTC31 is not set.
DTC12 FAULT IN IMMOBILIZER CONTROL MODULE
DESCRIPTION:
This DTC is set when an internal fault is detected in Immobilizer Control Module.
INSPECTION:
STEPACTIONYESNO
11) Ignition switch OFF.
2) Disconnect connectors from Immobi-
lizer Control Module.
3) Check for proper connection to Im-
mobilizer Control Module at all termi-
nals.
Are they in good condition?Substitute a known-good Immobilizer
Control Module and recheck.
NOTE:
After replacing with a known-good
Immobilizer Control Module, register
ECM/Immobilizer Control Module
code in ECM / PCM and Transponder
code and ECM/Immobilizer
Control Module code in Immobilizer
Control Module by performing
procedure described in ªProcedure
after Immobilizer Control Module
Replacementº section.Repair or replace.

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-23
DTC82 (P1622) FAULT IN ECM / PCM
DESCRIPTION:
This DTC is set when an internal fault is detected in ECM / PCM.
INSPECTION:
STEPACTIONYESNO
11) Ignition switch OFF.
2) Disconnect connectors from
ECM / PCM.
3) Check for proper connection
to ECM / PCM at all terminals.
Are they in good condition?Substitute a known-good ECM / PCM and
recheck.
NOTE:
After replacing with a known-good ECM /
PCM, register ECM/Immobilizer Control
Module code in ECM / PCM by performing
procedure described in ªProcedure after
ECM / PCM Replacementº section.Repair or replace.

YH4
GRAND
VITARA
10B
AIR BAG SYSTEM 10B-1
GENERAL DESCRIPTION10B- 3 . . . . . . . . . . . . .
System Components and Wiring
Location View and Connectors 10B- 4. . . . . . .
System Wiring Diagram 10B- 5. . . . . . . . . . . . . .
DIAGNOSIS10B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes 10B- 6. . . . . . . . . . . .
Use of Special Tools 10B- 6. . . . . . . . . . . . . . . . .
Intermittent and Poor Connections 10B- 8. . . . .
Air Bag Diagnostic System Check 10B-10. . . . .
Air bag diagnostic system check
flow table 10B-11. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code (DTC) check 10B-12.
Diagnostic trouble code (DTC)
clearance 10B-13. . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code table 10B-14. . . . . . . .
Table A - ªAIR BAGº warning lamp
comes ªONº steady 10B-16. . . . . . . . . . . . . . .
Table B - ªAIR BAGº warning lamp
does not come ªONº 10B-18. . . . . . . . . . . . . .
Table C - ªAIR BAGº warning lamp
flashes 10B-20. . . . . . . . . . . . . . . . . . . . . . . . . .
Table D - SDM cannot communicate
through the serial data circuit 10B-22. . . . . . . Code 15 - Passenger air bag initiator
circuit resistance high 10B-24. . . . . . . . . . . . .
Code 16 - Passenger air bag initiator
circuit resistance low 10B-26. . . . . . . . . . . . . .
Code 18 - Passenger air bag initiator
circuit short to ground 10B-28. . . . . . . . . . . . .
Code 19 - Passenger air bag initiator
circuit short to power circuit 10B-30. . . . . . . .
Code 21 - Driver air bag initiator
circuit resistance high 10B-32. . . . . . . . . . . . .
Code 22 - Driver air bag initiator
circuit resistance low 10B-34. . . . . . . . . . . . . .
Code 24 - Driver air bag initiator
circuit short to ground 10B-36. . . . . . . . . . . . .
Code 25 - Driver air bag initiator
circuit short to power circuit 10B-38. . . . . . . .
Code 31 - Power source voltage high 10B-40
Code 32 - Power source voltage low 10B-42.
Code 41 - Driver pretensioner initiator
circuit resistance high 10B-44. . . . . . . . . . . . .
Code 45 - Passenger pretensioner
initiator circuit resistance high 10B-44. . . . . .
Code 42 - Driver pretensioner initiator
circuit resistance low 10B-46. . . . . . . . . . . . . .
SECTION 10B
AIR BAG SYSTEM
WARNING:

Service on or around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in this section before performing service on or around the air bag system components or
wiring. Failure to follow WARNINGS could result in unintended activation of the system or could ren-
der the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above condi-
tions are not followed, parts or system damage could result.
CONTENTS