1999 SUZUKI GRAND VITARA connectors

YH4
GRAND
VITARA
1
1. Steering column hole cover 1. Steering column cover screw
2. Steering column upper cover
3. Steering column lower cover: Standard screw
: Tapping screw
*
* *
AIR BAG STEERING WHEEL AND COLUMN 3C1-9
3) Connect all connectors that have been removed in removal.
4) Install steering column upper and lower cover, and then tighten
steering column cover screws.
CAUTION:
When installing lower cover and upper cover, be careful
so that contact coil and combination switch lead wire is
not caught between covers.
5) Install steering column hole cover.
6) Install steering wheel to steering column. Refer to ªSTEERING
WHEELº in this section.
STEERING COLUMN
CAUTION:
Once the steering column is removed from the vehicle, the
column is extremely susceptible to damage.
Dropping the column assembly on its end could collapse
the steering shaft or loosen the plastic shear pins which
maintain column length leaning on the column assembly
could cause it to bend or deform.
Any of the above damage could impair the column's col-
lapsible design.
When loosening steering column mounting bolts, make
sure that steering column assembly and steering shaft low-
er assembly have been separated. Loosening them with
steering column assembly and steering shaft lower assem-
bly assembled could cause damage to bearing in steering
shaft lower assembly.
NOTE:
When servicing steering column or any column-mounted
component, remove steering wheel. But when removing steer-
ing column simply to gain access to instrument panel compo-
nents, leave steering wheel installed on steering column.

YH4
GRAND
VITARA
1. Steering column assembly
2. Steering shaft joint
3. Marks
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)1. Steering column hole cover
1
3C1-10 AIR BAG STEERING WHEEL AND COLUMN
REMOVAL
WARNING:
Never rest a steering column assembly on the steering
wheel with air bag (inflator) module face down and column
vertical. Otherwise personal injury may result.
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Remove steering wheel and contact coil and combination switch
assembly, if necessary. Refer to ªSTEERING WHEELº and
ªCONTACT COIL AND COMBINATION SWITCH ASSEMBLYº
in this section.
Perform the following procedure if not removing steering wheel
and/or combination switch.
ii) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
ii) Turn ignition switch to ªLOCKº position and remove key.
4) Remove steering column hole cover.
5) Disconnect all connectors for the following parts.

Contact coil and combination switch

Ignition switch
6) Make alignment marks on shaft joint and shaft (column side) for
a guide during reinstallation.
7) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in the figure).

YH4
GRAND
VITARA
1. Steering shaft joint
2. Steering shaft (column side)
3. Marks
1. Steering shaft joint
2. Bolt (column side)
3. Bolt (lower shaft assembly side)
1. Steering column hole cover
1
AIR BAG STEERING WHEEL AND COLUMN 3C1-13
4) Install steering shaft joint to steering shaft by matching it to
marks made before removal.
5) Install shaft joint bolt (column side) to steering shaft joint. Tighten
shaft joint bolt (column side) to specified torque first and then
shaft joint bolt (lower shaft assembly side) to specified torque.
Tightening Torque
(c): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
6) If contact coil and combination switch assembly is removed,
install it, referring to ªCONTACT COIL AND COMBINATION
SWITCH ASSEMBLYº in this section.
7) Connect all connectors that have been removed in removal.
8) Install steering column hole cover.
9) If steering wheel is removed, install it by referring to ªSTEER-
ING WHEELº in this section.
10) Connect negative battery cable.
11) After installing steering column assembly, be sure to enable air
bag system by referring to ªENABLING AIR BAG SYSTEMº un-
der ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
5E1-22 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. ABS hydraulic
unit / control
module connector
INSPECTION
STEPACTIONYESNO
1Is G sensor installed floor securely?Go to step 2.Tighten sensor or
bracket screw
securely. If not,
using new screw.
21) Ignition switch OFF.
2) Remove G sensor with bracket.
3) Check for proper connection to G sensor.
4) If OK then check G sensor referring to item
INSPECTION of G sensor.
Is it in good condition?Go to step 3.Replace G sensor.
31) Disconnect connectors from ABS hydraulic unit /
control module assembly (See Fig. 1) and G sensor.
2) Check for proper connection to ABS control module
at terminals ªA14º and ªA4º.
3) If OK, then turn ignition switch ON and measure
voltage between ªB / Wº terminal of sensor
connector and body ground.
Is it 10 ± 14 V?Go to step 4.ªB / Wº circuit open.
4Measure voltage between ªO / Wº terminal of sensor
connector and body ground.
Is it 0 V?Go to step 5.ªO / Wº circuit
shorted to power
circuit.
51) Ignition switch OFF.
2) Check that ªO / Wº circuit is free from open
or short to ground and ªO / Gº circuit.
Is it in good condition? (See Fig. 2)ªO / Gº circuit open.
If circuit is OK, substi-
tute a known-good
ABS hydraulic
unit / control module
assembly.ªO / Wº circuit open
or shorted to
ground or ªO / Gº
circuit.
Fig. 1 Fig. 2

YH4
GRAND
VITARA
5E1-30 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
DTC 71 (DTC C1071) ± ABS CONTROL MODULE
DESCRIPTION
This DTC will be set when an internal fault is detected in the ABS control module.
INSPECTION
STEPACTIONYESNO
11) Ignition switch OFF.
2) Disconnect connectors from ABS control module.
3) Check for proper connection to ABS control
module at all terminals.
Are they in good condition?Substitute a
known-good ABS
control module and
recheck.Repair or replace.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-31
1. Diagnosis
connector
(6 pins connector)
2. Diag. switch
terminal
3. Ground
4. Service wire
Brake
pedal
Ignition
sw.
Motor
Solenoid
Rear3.0 sec.
3.0
ON-VEHICLE SERVICE
PRECAUTION
When connector are connected to ABS hydraulic unit / control mod-
ule assembly, do not disconnect connectors of sensors and turn
ignition switch ON. Then DTC will be set in ABS control module.
ABS HYDRAULIC UNIT OPERATION CHECK
1) Check that basic brake system other than ABS is in good condi-
tion.
2) Check that battery voltage is 11V or higher.
3) With ªABSº warning lamp, check that no abnormality is de-
tected in ABS. Refer to ªDIAGNOSTIC TROUBLE CODE
(DTC) CHECKº in this section.
4) Lift up vehicle.
5) Set transmission to neutral and release parking brake.
6) Turn each wheel gradually by hand to check if brake dragging
occurs. If it does, correct.
7) With diag. switch terminal of diagnosis connector connected to
ground by using service wire, turn ignition switch ON and check
if ªABSº warning lamp indicates DTC 12.
8) Turn ignition switch OFF.
9) Perform following checks with help of another person.
Brake pedal should be depressed and then ignition switch
turned ON by one person and wheel should be turned by
another person's hand. At this time, check that:

Operation sound of solenoid is heard and wheel turns only
about 0.5 sec. (Brake force is depressurized).

Operation sound of pump motor is heard and pulsation is felt
at brake pedal.
10) If all 4-wheels cannot be checked during one ignition cycle
(OFF
ON), repeat Steps 8) and 9) till all 4 wheels are
checked.
If a faulty condition is found in Steps 9) and 10), replace hydrau-
lic unit / control module assembly.
11) Turn ignition switch OFF and remove service wire from diagno-
sis connector.

YH4
GRAND
VITARA
7B1
AUTOMATIC TRANSMISSION (4 A / T) 7B1-1
GENERAL DESCRIPTION7B1- 3 . . . . . . . . . . . . . .
CLUTCH / BRAKE FUNCTIONS 7B1- 5. . . . . . . . .
TABLE OF COMPONENT OPERATION 7B1- 6. . .
ELECTRONIC SHIFT CONTROL
SYSTEM 7B1- 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSIS7B1-17 . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTION IN DIAGNOSING
TROUBLE 7B1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLE 7B1-21. . . . . . . . . .
Customer Problem Inspection Form 7B1-23. . .
Malfunction Indicator lamp (MIL)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
ªO / D OFFº Lamp Check 7B1-24. . . . . . . . . . . . .
ªPOWERº Lamp Check 7B1-24. . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 7B1-24. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) Table7B1-24 . . .
Fail-Safe Table 7B1-25. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 7B1-26. . . . . . . . . . . . . . . . . . .
A / T Basic Check 7B1-27. . . . . . . . . . . . . . . . . . .
Trouble Diagnosis Table 1 7B1-28. . . . . . . . . . .
Trouble Diagnosis Table 2 7B1-28. . . . . . . . . . . Trouble Diagnosis Table 3 7B1-29. . . . . . . . . . .
Scan Tool Data 7B1-30. . . . . . . . . . . . . . . . . . . . .
Inspection of PCM and Its Circuit 7B1-30. . . . .
Wire Harness and Connectors 7B1-30. . . . . . . .
Diagnostic Flow Table A-1 7B1-31. . . . . . . . . . .
Diagnostic Flow Table A-2 7B1-33. . . . . . . . . . .
Table B-1 ªO / D OFFº Light Circuit
Check 7B1-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 ªO / D OFFº Light Circuit
Check 7B1-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 ªPOWERº Light Circuit
Check 7B1-37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-4 ªPOWERº Light Circuit
Check 7B1-38. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B1-39. .
DTC P0715 Input / Turbine Speed
Sensor Circuit Malfunction 7B1-42. . . . . . . . . .
DTC P0720 Output Speed Sensor
Circuit Malfunction 7B1-44. . . . . . . . . . . . . . . . .
DTC P0741 TCC Solenoid Valve
Performance or Stuck Off 7B1-46. . . . . . . . . . .
DTC P0743 TCC Solenoid Electrical 7B1-47. .
DTC P0751 Shift Solenoid Valve-A (#1)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
DTC P0756 Shift Solenoid Valve-B (#2)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
SECTION 7B1
AUTOMATIC TRANSMISSION
(4 A
/
T)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
7B1-26 AUTOMATIC TRANSMISSION (4 A / T)
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

A / T fluid ± ± ± ± ± level, leakage, color

A / T fluid hoses ± ± ± ± ± disconnection, looseness, deterioration

Throttle (accelerator) cable ± ± ± ± ± play, installation

A / T throttle cable ± ± ± ± ± play, installation

A / T select cable ± ± ± ± ± installation, operation

Engine oil ± ± ± ± ± level, leakage

Engine coolant ± ± ± ± ± level, leakage

Battery ± ± ± ± ± fluid level, corrosion of terminal

Connectors of electric wire harness ± ± ± ± ± disconnection, friction

Fuses ± ± ± ± ± burning

Parts ± ± ± ± ± installation, damage

Bolt ± ± ± ± ± looseness

Other parts that can be checked visually
Also check following items at engine start, if possible.

ªO / D OFFº lamp

ªPOWERº lamp


Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Other parts that can be checked visually
Section 0B
Section 7B1
Section 6E1 / 6E2
Section 7B1
Section 7B1
Section 0B
Section 0B
Section 6 / 6-1 / 7B1
Section 8
Section 7B1
Section 7B1
Section 6 / 6-1
Section 6H
Section 8 (Section 6A1 / 6A2 /
6A4 for pressure check)