1999 SUZUKI GRAND VITARA acc

YH4
GRAND
VITARA
LH steering vehicle shown
X-X:Horizontal center line of headlight bulbs
A-A:Vertical center line of left headlight bulb
B-B:Vertical center line of right headlight bulb1. Screen
2. For right / left adjustment
3. For up / down adjustment
(for vehicle without leveling system)
4. For up / down adjustment
(for vehicle with leveling system)
5. Headlight leveling actuatorHOT
SPOT LH. HEADLIGHT RH. HEADLIGHT
LIGHTING SYSTEM 8B-7
BULB REPLACEMENT
WARNING:
Don't touch when the bulb is hot.
1) Disconnect negative cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and install in reverse removal procedure.
HEADLIGHT AIMING WITH SCREEN
NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to perform its aiming.

When inspecting and adjusting headlight with leveling sys-
tem, make sure to set the leveling switch to ª0º position with
IG switch ON.
Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall as below
ahead of headlight surface.
Clearance ªaº: 10 m (32.8 ft)
b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-
sion.
d) Carry out one driver aboard.
Driver's weight: 75 kg (165 lb)
Adjustment
1) Check to see if hot spot (high intensity zone) of each main (low)
beam axis falls as illustrated.
Clearance ªHº: Approx. 130 mm (5.15 in.)
2) If headlight aiming is not set properly, align it to specification by
adjusting aiming screw and aiming gear.

YH4
GRAND
VITARA
8B-8 LIGHTING SYSTEM
HEADLIGHTS WITH LEVELING SYSTEM
(IF EQUIPPED)
LEVELING SWITCH
INSPECTION
To check the switch operation, substitute it with a new one. If proper
operation is obtained, it means the switch is defective.
Replace it with a new one.
LEVELING ACTUATOR
INSPECTION
All headlight system couples connected including leveling actuator
and switch, and at Ignition switch ON, listen to the leveling actuator
sound on both actuators according to the movement of the leveling
switch. If no sound is heard with the movement of the leveling
switch, replace headlight assembly.

YH4
GRAND
VITARA
8C
INSTRUMENTATION / DRIVER INFORMATION 8C-1
GENERAL DESCRIPTION8C- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8C- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8C- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8C- 2. . . . . . . . . . . . . . . . .
Abbreviations 8C- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8C- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8C- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8C- 2. . . . . . . . . . . . . . . .
Combination Meter 8C- 2. . . . . . . . . . . . . . . . . . .
DIAGNOSIS8C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 4. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 4. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C- 4. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Remainder Warning Buzzer 8C- 5. . . . . . . Seat Belt Warning Light (If Equipped) 8C- 5. . .
Ignition Key Remainder Warning
Buzzer (If Equipped) 8C- 5. . . . . . . . . . . . . . . . .
Cigarette Lighter and Accessory Socket 8C- 5.
ON-VEHICLE SERVICE8C- 6 . . . . . . . . . . . . . . . .
Ignition (Main) Switch 8C- 6. . . . . . . . . . . . . . . . .
Combination Meter 8C- 7. . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 8. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 9. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C-11. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Key Remainder (If Equipped) /
Light Remainder Warning Buzzer 8C-12. . . . . .
Door Switch 8C-13. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Warning Light (If Equipped) 8C-13. . .
SECTION 8C
INSTRUMENTATION/DRIVER INFORMATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
INSTRUMENTATION / DRIVER INFORMATION 8C-5
BRAKE AND PARKING BRAKE WARNING LIGHT
TroublePossible CauseCorrection
Brake warning light does
not light up
Bulb in combination meter blown

ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

Printed plate in combination meter
faulty

Parking brake switch faulty

Brake fluid level switch faulty

Wiring or grounding faultyReplace bulb
Replace fuse to check for short
Replace printed plate
Replace parking brake switch
Replace brake fluid level switch
Repair
LIGHT REMAINDER WARNING BUZZER
TroublePossible CauseCorrection
Light remainder warning
buzzer shows no
sounding
ªTAILº fuse blown

Buzzer faulty

Wiring or grounding faulty

Driver side door switch faultyReplace fuse to check for short
Replace buzzer
Repair
Replace door switch
SEAT BELT WARNING LIGHT (IF EQUIPPED)
TroublePossible CauseCorrection
Seat belt warning light
does not light up
Bulb in combination meter blown

ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

Seat belt switch faulty

Wiring or grounding faultyReplace bulb
Replace fuse to check for short
Replace seat belt switch
Repair
IGNITION KEY REMAINDER WARNING BUZZER (IF EQUIPPED)
TroublePossible CauseCorrection
Ignition key remainder
warning buzzer shows no
sounding
ªDOMEº fuse blown (Hard Top Model)
ªDOMº fuse blown (Canvas Top
Model)

Buzzer faulty

Wiring or grounding faulty

Driver side door switch faulty

Ignition key switch faultyReplace fuse to check for short
Replace buzzer
Repair
Replace door switch
Replace ignition key switch
CIGARETTE LIGHTER AND ACCESSORY SOCKET
TroublePossible CauseCorrection
Cigarette lighter /
accessory socket shows
no operation
ªCIGARº fuse blown (Hard Top Model)
ªCIGº fuse blown (Canvas Top Model)

Ignition switch faulty

Cigarette lighter / accessory socket
faulty

Wiring or grounding faultyReplace fuse to check for short
Replace ignition switch
Replace cigarette lighter / accessory
socket
Repair

YH4
GRAND
VITARA
8C-6 INSTRUMENTATION / DRIVER INFORMATION
KeyPosition
TerminalWire
color
Hard Top Model
Canvas Top Model
ON-VEHICLE SERVICE
IGNITION (MAIN) SWITCH
INSPECTION
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Disconnect main switch lead wire coupler.
4) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace ignition
(main) switch.
+B+ACCIG1-1IG1-2IG2STL1L2K1K2
W/YBlB/WB/WY/BB/YBBGG
OUTLOCKLOCK
ACC
IN
ON
START
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Remove steering column referring to Section 3C1 of this manu-
al. Then remove steering lock / ignition (main) switch from steer-
ing column.
INSTALLATION
1) Install steering lock / ignition (main) switch to steering column.
Install steering column assembly referring to Section 3C1 of this
manual.
2) Enable air bag system. Refer to ENABLING AIR BAG SYSTEM
in Section 10B of this manual.
NOTE:
When installing steering column, special care must be tak-
en for tightening sequence and its torque.

YH4
GRAND
VITARA
Terminal
Key
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-21
6) Connect negative cable at battery.
7) Check that the voltage and resistance between following termi-
nals are specifications.
Terminals
ConditionSpecification
E02-7 and
groundAnytime10 ± 14 V
E02-14 and
groundAnytimecontinuity
E02-8 and
When driver side door key
switch is OFF positionNo continuity
groundWhen driver side door key
switch is LOCK positionContinuity
E02-9 and
When driver side door key
switch is OFF positionNo continuity
groundWhen driver side door key
switch is UNLOCK positionContinuity
If check result is not satisfactory, repair circuit and recheck.
If check result is satisfactory, replace controller.
KEY CYLINDER SWITCH (DRIVER SIDE)
Check for continuity between terminals according to the key action
shown below.
321
LOCK
OFF
UNLOCK

YH4
GRAND
VITARA
8D-28 WINDOWS, MIRRORS, SECURITY AND LOCKS
TRANSMITTER
REPLACEMENT OF THE BATTERY
If the transmitter becomes unreliable, replace the battery.
As the battery power is consumed, the operation distance will be
shorter.
1) Put the edge of a coin or a flat blade screw driver in the slot (1)
of the transmitter and pry it open.
2) Replace the battery (lithium disc-type CR2032 or equivalent) so
its
terminal faces the ª+º mark of the transmitter.
CAUTION:
Use care not to allow grease or dirt to be attached on the
printed circuit board and the battery.
3) Close the transmitter firmly.
4) Make sure the door locks can be operated with the transmitter.
NOTE:

To prevent theft, be sure to break the transmitter before
discarding it.

Dispose of the used battery properly according to appli-
cable rules or regulations. Do not dispose of lithium bat-
teries with ordinary household trash.

YH4
GRAND
VITARA
8D-32 WINDOWS, MIRRORS, SECURITY AND LOCKS
3. To open
4. To close
3. Left turn
4. Right turn
Terminal
Switch
Terminal
Switch
POWER SLIDING ROOF (IF EQUIPPED)
INSPECTION
SLIDING ROOF SWITCH
Check switch for continuity between terminals as shown below.
Slide Switch (1)
CDFCDF
OPEN
OFF
CLOSE
Tilt Switch (2)
EDBEDB
UP
OFF
DOWN
SLIDING ROOF MOTOR ASSEMBLY
1) Remove head lining. Refer to Section 9 for detail.
2) Remove sliding roof motor assembly (1).
3) Connect known-good sliding roof switch (2) to sliding roof motor
assembly.
4) Connect 12 V battery positive terminal to terminal ªAº of motor
assembly (1) and battery negative terminal to terminal ªBº of mo-
tor assembly (1).
5) Check that the sliding roof motor (1) runs according to the move-
ment of the sliding roof switch (2).
Sliding Roof Switch
Motor
Tilt upturns left
Tilt downturns right
Slide openturns right
Slide closeturns left
If motor does not operate as above, replace sliding roof motor
assembly (1).