1999 SUZUKI BALENO sound

WARRANTY POLICY
60G-74E

dealer/service station,

(k) any vehicle which has been used for purposes other than

what it was designed for.

(I) any damage or deterioration caused by industrial pollution

and bird droppings,

(m) insignificant defects which do not affect the function of the

vehicle including without limitation sound, vibration and fluid

seep,

(n) any natural wear and tear including without limitation, ageing

etc.

For Maruti Air-Conditioned Vehicles

(o) V-belts, hoses and gas leaks.

(5) Extent of Warranty:

This warranty is the entire written warranty given by Maruti for

Maruti vehicles and no dealer or its or his agent or employee

is authorised to extend or enlarge this warranty and no dealer

or its or his agent or employee is autorised to make any oral

warranty on Maruti's behalf.

Maruti reserves the right to add any improvements or change

the design of any model at any time with no obligation to make

the same changes on units previously sold.

(6) Warranty Service:

To obtain warranty service, the complete vehicle must be

presented at the owner's expenses to any authorised Maruti

dealer.

(7) Owner's Warranty Responsibilities:
It is responsibility of each owner to:

(a) make certain that the warranty registration/PDI card was

completed at the time of delivery of the vehicle;

(b) have performed, at his own expenses, by an Maruti

authorised dealer/service station all the service inspections

specified in the Maruti "Owner's Manual and Service Booklet"

and maintain adequate proof that such service inspections

have been performed.

(c) make certain that the Maruti authorised dealer/service station

performing the service inspection has certified the work on

the "Maintenance Service Record" page in the "Owner's

Manual and Service Booklet" and

(d) present the Maruti "Owner's Manual and Service Booklet" to

the authorised Maruti dealer whenever requesting service

inspections or warranty service.

If the "Owner's Manual and Service Booklet" should be lost or

destroyed the owner should consult the authorised Maruti dealer from

whom the vehicle was purchased for instructions concerning

replacement of the "Owner's Manual and Service Booklet".

(8) Disclaimer of Consequential Damage:

Maruti assumes no responsibility for loss of vehicle, loss of time,

inconvenience or any other indirect incidental or consequential

damage resulting from the vehicle not being available to the

owner because of any defect covered by this warranty.

(9) Change of owner

Even if ownership of the vehicle changes, the remaining

warranty period is effective for the new owner.

2-2

60G-74E

EMISSION WARRANTY

Maruti offers the Emission Warranty on all Maruti vehicles (aparts from the Regular warranty and will run parallel to the regular

product warranty) only in four metropolitan cities (New Delhi, Kolkata, Mumbai and Chennai) with effect from July 1st, 2001.

Terms:

The Emission Warranty will be applicable for 80,000 kms or 3 years (Whichever comes earlier) from the date of delivery to the

first owner. The remaining warranty terms will be valid in case of any change in ownership provided the production of all valid documents.

Conditions :

1. Under Emission Warranty, Warranty claims will be admitted for a prima facie examination, in case vehicle fails to meet to the

Emission Standard as specified In sub rule (2) of rule no. 115 of Central Motor Vehicles Rules (CMVR), 1989.

2. The warranty claims will only be accepted after examination carried out by Maruti or it's dealer which leads to firm conclusions

that the

a) Original settings have not been tempered in any case.

b) Part (as given in Annexure-A) has a manufacturing defect.

c) Vehicle is unable to meet the Emission Standards (as given in 1.), inspite of the vehicle having been maintained and used

in accordance with the instructions as specified in Owner's Manual and Service Booklet and the used fuel and different oils

(Engine oil, Transmission oil, Brake oil etc.) are also as per specification.

3. The method of examination for deciding the warranty of the parts will be at the sole discretion of Maruti and it's dealer and

results of the examination will be final and binding. If after examination, the warrantable condition is not established, Maruti

and it's dealer has the right to charge all, or part of the cost of such examination.

4. Under Emission Warranty, the parts (as given in Annexure-A) will be changed free of cost, but the consumables will be charged

as per actual.

5. If the part covered under Emission Warranty or the associated parts, are not independently replaceable, on account of these

being integral parts of a complete assembly, Maruti and it's dealer will have the sole discretion to replace either the entire assembly

or by using some of the parts of the system through suitable repairs or modifications.
8

9

60G-74E

BEFORE DRIVING

REMOTE KEYLESS ENTRY SYSTEM

Other Controls (if equipped)
KEYS

60G-50-001E

Remote keyless entry system is installed in

your vehicle. The general features of keyless

entry system are;

1. Remote lock/arming and remote unlock/

disarming.

2. Doors/trunk/bonnet protection.

3. Doors/trunk/bonnet open signal.

4. Personal protection alarm.

5. Mute lock/unlock.

6. Starter immobiliser.

7. Permanent siren chirp enable/disable

(programmable mode).

8. Two stage shock/impact sensor

(programmable mode).

9. Emergency disarm by personalised

PINCODE (programmable mode).

10. Car locator

11. Flashing LE.D.

15
Initially the system is programmed in factory

default. The features operative in factory

default are;

1. Remote lock/arming and remote unlock/

disarming.

2. Doors/trunk/bonnet protection.

3. Doors/trunk/bonnet open signal while

locking/arming.

4. Personal protection alarm.

5. Starter immobiliser.

6. Mute lock/unlock.

7. Permanent siren chirp enable/disable.

8. Emerging disarm by personalised

PINCODE.

9. Car locator.

10. Flashing LE.D.

The system can always be programmed back

to factory default for restoration of original

setting of the system.

For more detail and warranty condition, please

refer to the Owner's Manual of "Maruti Mobile

Security".
70F-01-003

Your vehicle comes with a pair of identical keys.

Keep the spare key in a safe place.

One key can open all of the locks on the vehicle.

The key identification number is stamped on a

metal tag provided with the keys. Keep

the tag in a safe place. If you lose your

keys, you will need this number to have

new keys made. Write the number down

and keep it in a safe accessible place away from

the vehicle.

NOTE:

Keep the spare key very carefully. When it

is lost, consult your dealer by quoting key number.

3-2

BEFORE DRIVING
60G-74E

DOOR LOCKS

60G-03-003

Ignition Key Reminder (if equipped)

A buzzer sounds intermittently to remind you

to remove the ignition key if it is in the ignition

switch when the driver's door is opened.
72F-03-002E

To lock a front door from outside the

vehicle:

a) Insert the key fully and turn the top of

the key toward the front of the vehicle,

or

b) Push in the lock knob down and hold

the door handle up as you close the

door.

To unlock a front door from outside the

vehicle, insert the key fully and turn the top

of the key toward the rear of the vehicle.

To lock a rear door from outside the vehicle,

push in the lock knob down and close the

door.
60G-03-004E

To lock a door from inside the vehicle, push

the lock knob down. Pull the lock knob up to

unlock the door.

3-3
16
Always lock all doors when driving.

Locking the door prevents occupants

from being thrown from the vehicle in

the event of an accident. It also helps

prevent unintentional opening of the

doors.

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

60G-74E

STEERING COLUMN CONTROLS

WINDSCREEN WIPER AND

WASHER LEVER

60G-04-007E

Windscreen Wipers

To turn the windscreen wipers on, move the

lever down to one of the three operating

positions. In the "INT position (if equipped),

the wipers operate intermittently. The "INT'

position is very convenient for driving in mist

or light rain. In the "LO" position, the wipers

operate at a steady low speed. In the "HI"

position, the wipers operate at a steady high

speed. To turn off the wipers, move the lever

back to the "OFF position.
60G-04-008E

If the lever is equipped with "INT TIME" control,

turn the control toward the "SLOW" or "FAST'

positions to adjust the intermittent wiper

operation to the desired interval.

60G-04-011E

The operation of windscreen wiper and washer

Type-2 is same as Type-1.
60G-04-009E

Windscreen Washer

To spray windscreen washer fluid, pull the

lever toward you. The windscreen wipers will

automatically turn on at low speed if

they are not already on and the "INT" position

is equipped.

To prevent windscreen icing in cold

weather, turn on the defroster to heat

the windscreen before and during

windscreen washer use.

Do not use radiator antifreeze in the

windscreen washer reservoir. It can

severely impair visibility when

sprayed on the windscreen, and can

also damage your vehicle's paint.

35

4-4

STEERING COLUMN CONTROLS
60G-74E

CAUTION

To help prevent damage to the

windscreen wiper and washer system

components, you should take the

following precautions:

• Do not continue to hold in the lever

when there is no windscreen washer

fluid being sprayed or the washer

motor can be damaged.

• Do not attempt to remove dirt from

a dry windscreen with the wipers or

you can damage the windscreen and

the wiper blades. Always wet the

windscreen with washer fluid before

operating the wipers.

• Clear ice or packed snow from the

wiper blades before using the

wipers.

• Check the washer fluid level

regularly. Check it often when the

weather is bad.

• Only fill the washer fluid reservoir

3/4 full during cold weather to allow

room for expansion if the

temperature falls low enough to

freeze the solution.
HORN
REAR WIPER AND WASHER

(if equipped)

60G-04-010

Press the horn button of the steering wheel to

sound the horn. The horn will sound with the

ignition switch in any position.
Press the button located at the end of the

windscreen wiper and washer lever to operate

the rear washer and turn the lever anti

clockwise to operate the rear washer.

4-5
36

OTHER CONTROLS AND EQUIPMENTS

60G-74E

FUEL FILLER CAP

60G-06-002

The fuel filler cap is located on the left rear

side of the vehicle. The fuel filler lid can be

unlocked by pulling up the opener lever located

on the outboard side of the driver's seat and

locked by simply closing the lid.

Remove the fuel filler cap slowly. The

fuel may be under pressure and may

spray out, causing injury.
Petrol Is extremely flammable. Do not

smoke when refuelling, and make sure

there are no open flames or sparks in

the area.
60G-06-OO3

The fuel tank filler cap has a "screw-on ratcheting

type" feature.

• To remove - turn the cap counterclockwise.

Turn the cap slowly to allow any residual

pressure to escape.

• To install - turn the cap clockwise and

tighten it securely until a "ratcheting"

(clicking) sound is heard. The "ratcheting"

sound indicates that the cap is on properly.

6-3
56

60G-74E
OTHER CONTROLS AND EQUIPMENT

FOLDING REAR SEATS

70F-04-008E

If you need to replace the fuel cap, use

only a cap specified for your model.

Using an improper fuel cap can cause

a serious malfunction of the fuel

system. You can get the correct

replacement cap from your MARUTI

dealer.
63B-06-013

The rear seat of your vehicle can be folded

forward ro provide additional luggage space.

To lower the seatback, hook the webbing of

both outboard lap-shoulder belts in the belt

hangers, pull up the lock knobs (© and @)

simultaneously and fold forward the seatback.

To raise the seatback, lift it up and push back

until it locks into place.

When you move a seatback, make sure

the belt webbing is hooked in the belt

hangers (if equipped) so the seat belts

are not caught by the seatback, seat

hinge, or seat latch.This helps prevent

damage to the belt system.
63B-06-014

When returning a rear seat to the

normal position, make sure that

movement of the seatback is

unobstructed and the seatback is

securely latched.

57

6-4

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68