1999 SUBARU FORESTER ground clearance

E: CONTROL MODULE I/O SIGNAL
B6M0972
Content Terminal No. Measuring condition
Empty 1 Ð
Ignition switch (ON) 2 (INPUT) Battery voltage is present when ignition switch is turned ON.
Passive arm 3 Ð
Empty 4 Ð
Door switch and rear gate latch
switch5 (INPUT) 0 V is present when any door is open.
Empty 6 Ð
Keyless entry control module 7 Ð
Keyless entry control module 8 Ð
Security indicator light 9 (OUTPUT) 0 V is present when activating the alarm operation.
Keyless entry control module 10 Ð
Power supply for clearance light
(Back-up)11 Battery voltage is constantly present.
Clearance light 12 (OUTPUT) Battery voltage is present when activating the alarm operation.
Power supply (Back-up) 13 Battery voltage is constantly present.
Ground 14 Ð
Interrupt relay 15 (OUTPUT) 0 V is present when activating the alarm operation.
Empty 16 Ð
Empty 17 Ð
Empty 18 Ð
74
6-2[T5E0]DIAGNOSTICS
5. Security System

5F117 : CHECK PASSIVE ARM.
1) Remove the driver's side sill cover. [W5A0].>
2) Connect the white connector (1-pin) at driver
side front lower pillar.
3) Close all doors and the rear gate.
:Does the arming automatically func-
tion after 1 minute?
: Go to step5F118.
: Go to step5 F 111.
5F118 : CHECK BATTERY DISCONNECT
PROTECTION.
1) Press the UNLOCK/DISARM button.
2) Connect the white connector (1-pin) at front pil-
lar lower.
3) Install the driver's side sill cover. [W5A0].>
4) Open the front hood.
5) Press the LOCK/ARM button.
6) Disconnect the ground cable from battery.
7) Connect the ground cable to battery.
:Does re-arming function automati-
cally?
: End of basic diagnostics procedure.
Press the UNLOCK/DISARM button,
and then close all doors and the rear
gate. Perform ignition switch position
turned LOCK to ON to LOCK.
: Replace security control module. to 6-2 [W14A1].>
2. DIAGNOSTICS ITEM 1
5F21 : CHECK FUSE.
Remove and visually check fuse No. 7 (in main
fuse box).
:Is fuse No. 7 blown?
: Replace fuse (20 A).
: Go to step5F22.
5F22 : CHECK FUSE.
Remove and visually check fuse No. 5 (in fuse
box).
:Is fuse No. 5 blown?
: Replace fuse (10 A).
: Go to step5F23.
5F23 : CHECK CLEARANCE LIGHT BULB.
Remove and visually check each clearance light
bulb.
:Is the bulb blown?
: Replace clearance light bulb.
: Go to step5F24.
5F24 : CHECK POWER SUPPLY FOR
CLEARANCE LIGHT.
Measure voltage between main fuse box connec-
tor (F68) and chassis ground.
Connector & terminal
(F68) No. 4 (+) Ð Chassis ground (þ):
B6M1357A
:Is the voltage more than 10 V?
: Go to step5F25.
: Repair wiring harness between main
fuse box and battery.
77
[T5F2]6-2DIAGNOSTICS
5. Security System

5F25 : CHECK POWER SUPPLY FOR
CLEARANCE LIGHT.
1) Disconnect connector from security control
module.
2) Measure voltage between security control mod-
ule connector (B93) and chassis ground.
Connector & terminal
(B93) No. 11 (+) Ð Chassis ground (þ):
B6M0974A
:Is the voltage more than 10 V?
: Go to step5F26.
: Repair wiring harness between security
control module and main fuse box.
5F26 : CHECK HARNESS CONNECTOR
BETWEEN SECURITY CONTROL
MODULE AND FUSE BOX.
1) Disconnect connector (B158) from fuse box.
2) Measure resistance between security control
module connector (B93) and fuse box connector
(B158).
Connector & terminal
(B93) No. 12 Ð (B158) No. 11:
S6M0457A
:Is the resistance less than 10W?
: Go to step5F27.
: Repair wiring harness between security
control module and fuse box.5F27 : CHECK FUSE BOX CIRCUIT.
1) Connect connector (B158) to fuse box.
2) Measure resistance between fuse box connec-
tor (B158) and (F41).
Connector & terminal
(B158) No. 11 Ð (F41) No. 1:
S6M0458A
:Is the resistance less than 10W?
: Go to step5F28.
: Repair or replace fuse box.
5F28 : CHECK FUSE BOX CIRCUIT.
Measure resistance between fuse box connector
(B158).
Connector & terminal
(B158) No. 10 Ð No. 11:
B6M1364B
:Is the resistance less than 10W?
: Go to step5F29.
: Repair or replace fuse box.
78
6-2[T5F2]DIAGNOSTICS
5. Security System

5F29 : CHECK HARNESS CONNECTOR
BETWEEN FRONT CLEARANCE
LIGHT AND FUSE BOX.
1) Disconnect connector from front clearance light
RH and fuse box.
2) Measure resistance between front clearance
light RH connector (F3) and fuse box connector
(F41).
Connector & terminal
(F3) No. 1 Ð (F41) No. 1:
B6M1365B
:Is the resistance less than 10W?
: Go to step5F210.
: Repair wiring harness between front
clearance light RH and fuse box.5F210 : CHECK HARNESS CONNECTOR
BETWEEN FRONT CLEARANCE
LIGHT AND FUSE BOX.
1) Disconnect connector from front clearance light
LH.
2) Measure resistance between front clearance
light LH connector (F19) and fuse box connector
(F41).
Connector & terminal
(F19) No. 1 Ð (F41) No. 1:
B6M1366B
:Is the resistance less than 10W?
: Go to step5F211.
: Repair wiring harness between front
clearance light LH and fuse box.
5F211 : CHECK HARNESS CONNECTOR
BETWEEN FRONT CLEARANCE
LIGHT AND CHASSIS GROUND.
Measure resistance between front clearance light
RH connector (F3) and chassis ground.
Connector & terminal
(F3) No. 2 (+) Ð Chassis ground (þ):
B6M0980C
:Is the resistance less than 10W?
: Go to step5F212.
: Repair wiring harness between front
clearance light RH and chassis ground.
79
[T5F2]6-2DIAGNOSTICS
5. Security System

5F212 : CHECK HARNESS CONNECTOR
BETWEEN FRONT CLEARANCE
LIGHT AND CHASSIS GROUND.
Measure resistance between front clearance light
LH connector (F19) and chassis ground.
Connector & terminal
(F19) No. 2 (+) Ð Chassis ground (þ):
B6M0981C
:Is the resistance less than 10W?
: Go to step5F213.
: Repair wiring harness between front
clearance light LH and chassis ground.
5F213 : CHECK HARNESS CONNECTOR
BETWEEN REAR CLEARANCE
LIGHT AND FUSE BOX.
1) Disconnect connector from rear clearance light
RH and fuse box.
2) Measure resistance between rear clearance
light RH connector (R26) and fuse box connector
(B158).
Connector & terminal
(R26) No. 1 Ð (B158) No. 10:
S6M0459A
:Is the resistance less than 10W?
: Go to step5F214.
: Repair wiring harness between rear
clearance light RH and fuse box.5F214 : CHECK HARNESS CONNECTOR
BETWEEN REAR CLEARANCE
LIGHT AND FUSE BOX.
1) Disconnect connector from rear clearance light
LH.
2) Measure resistance between rear clearance
light LH connector (R28) and fuse box connector
(B158).
Connector & terminal
(R28) No. 1 Ð (B158) No. 10:
S6M0460A
:Is the resistance less than 10W?
: Go to step5F215.
: Repair wiring harness between rear
clearance light LH and fuse box.
5F215 : CHECK HARNESS CONNECTOR
BETWEEN REAR CLEARANCE
LIGHT AND CHASSIS GROUND.
Measure resistance between rear clearance light
RH connector (R26) and chassis ground.
Connector & terminal
(R26) No. 4 (+) Ð Chassis ground (þ):
S6M0461A
:Is the resistance less than 10W?
: Go to step5F216.
: Repair wiring harness between rear
clearance light RH and chassis ground.
80
6-2[T5F2]DIAGNOSTICS
5. Security System

5F216 : CHECK HARNESS CONNECTOR
BETWEEN REAR CLEARANCE
LIGHT AND CHASSIS GROUND.
Measure resistance between rear clearance light
LH connector (R28) and chassis ground.
Connector & terminal
(R28) No. 4 (+) Ð Chassis ground (þ):
S6M0462A
:Is the resistance less than 10W?
: Replace security control module. to 6-2 [W14A1].>
: Repair wiring harness between rear
clearance light LH and chassis ground.
3. DIAGNOSTICS ITEM 2
5F31 : CHECK SECURITY INDICATOR
LIGHT COMES ON.
1) Disconnect connector from security control
module.
2) Measure resistance between security control
module connector (B93) and chassis ground.
Connector & terminal
(B93) No. 9 (+) Ð Chassis ground (þ):
B6M1369A
:Does the indicator light come on?
: Replace security control module. to 6-2 [W14A1].>
: Go to step5F32.
5F32 : CHECK POWER SUPPLY FOR
SECURITY INDICATOR LIGHT.
1) Disconnect connector from combination meter.
2) Measure voltage between combination meter
connector (i10) and chassis ground.
Connector & terminal
(i10) No. 1 (+) Ð Chassis ground (þ):
S6M0463A
:Is the voltage more than 10 V?
: Go to step5F33.
: Repair wiring harness between security
indicator light and main fuse box.
81
[T5F3]6-2DIAGNOSTICS
5. Security System

2. Fuel Flap
A: REMOVAL AND INSTALLATION
1. FUEL FLAP
1) Remove bolts which hold hinge to vehicle body,
and detach fuel flap and hinge as a unit.
S5M0150
2) Install in the reverse order of removal.
CAUTION:
Make sure the clearance between the fuel flap
and vehicle body is equal at all points.
2. FUEL FLAP OPENER
1) Remove driver's seat and rear seat cushion.
2) Turn over the floor mat (driver's side).
3) Remove all clips which hold cable.
4) Disconnect cable (A) from pull handle (B).
5) Detach pull handle by removing bolts.
S5M0291B
6) Detach fuel lock holder by turning it.
7) Install in the reverse order of removal.
CAUTION:
After installing opener cable, ensure it moves
smoothly.
3. Front Bumper
A: REMOVAL AND INSTALLATION
1) Disconnect the ground cable from the battery.
2) Remove front fog light.
3) Remove the front grille.
4) Remove the extension of both sides.
S5M0152A
5) Remove the seven clips and then detach plate
(A).
S5M0397A
6) Remove under cover.
7) Remove the seven clips from under side of
bumper.
S5M0153
31
[W3A0]5-1SERVICE PROCEDURE
3. Front Bumper

2. Fuel Flap
A: REMOVAL AND INSTALLATION
1. FUEL FLAP
1) Remove bolts which hold hinge to vehicle body,
and detach fuel flap and hinge as a unit.
S5M0150
2) Install in the reverse order of removal.
CAUTION:
Make sure the clearance between the fuel flap
and vehicle body is equal at all points.
2. FUEL FLAP OPENER
1) Remove driver's seat and rear seat cushion.
2) Turn over the floor mat (driver's side).
3) Remove all clips which hold cable.
4) Disconnect cable (A) from pull handle (B).
5) Detach pull handle by removing bolts.
S5M0291B
6) Detach fuel lock holder by turning it.
7) Install in the reverse order of removal.
CAUTION:
After installing opener cable, ensure it moves
smoothly.
3. Front Bumper
A: REMOVAL AND INSTALLATION
1) Disconnect the ground cable from the battery.
2) Remove front fog light.
3) Remove the front grille.
4) Remove the extension of both sides.
S5M0152A
5) Remove the seven clips and then detach plate
(A).
S5M0397A
6) Remove under cover.
7) Remove the seven clips from under side of
bumper.
S5M0153
31
[W3A0]5-1SERVICE PROCEDURE
3. Front Bumper