1999 SUBARU FORESTER sensor

5. Side Airbag Harness
A: REMOVAL AND INSTALLATION
1) Turn ignition switch off.
2) Disconnect ground cable from battery and wait
for at least 20 seconds before starting work.
3) Remove front seat and
roll up floor mat .
4) Remove console box.
5) Disconnect the two 12-pin yellow connectors
from airbag control module.
6) Remove side airbag sensor [W7A0].> and then disconnect connector from side
airbag sensor.
7) Detach clips and then remove side airbag har-
ness.
S5M0307
8) Install in the reverse order of removal.
6. Airbag Control Module
A: REMOVAL AND INSTALLATION
CAUTION:
IDo not disassemble the airbag control mod-
ule.
G5M0322
IIf the airbag control module is deformed, or
if water damage is suspected, replace the air-
bag control module with a new genuine part.
G5M0323
IAfter removal, keep the airbag control mod-
ule on a dry, clean surface away from heat and
light sources, and moisture and dust.
G5M0324
1) Turn ignition switch off.
2) Disconnect ground cable from battery and wait
for at least 20 seconds before starting work.
3) Remove lower cover.
4) Remove instrument panel console. [W1A0].>
5) Disconnect connector from airbag control mod-
ule.
12
5-5[W5A0]SERVICE PROCEDURE
5. Side Airbag Harness

6) Using T40 TORXTbit (Tamper resistant type),
remove the four TORXTbolts in numerical
sequence shown in figure. Discard the old TORXT
bolts.
CAUTION:
Use new TORXTbolts during re-assembly.
S5M0219A
7) Install in the reverse order of removal.
7. Side Airbag Sensor
A: REMOVAL AND INSTALLATION
CAUTION:
IIf the side of the vehicle body is damaged by
a collision, be sure to check the left and right
side airbag sensors, even if the airbag was not
inflated. If any damage to the sensor or any
deformation of the sensor mount is found,
replace with a new genuine part.
IWhen painting or performing sheet metal
work on the side part of vehicle body, including
the side sill, center pillar, front and rear doors,
take utmost care not to apply dryer heat, paint-
ing mist, or the flame of the welding burner
directly to the side airbag sensors and wire
harness of the airbag system.
1) Turn ignition switch off.
2) Disconnect ground cable from battery and wait
for at least 20 seconds before starting work.
3) Remove center pillar lower trim. [W5A1].>
4) Detach ELR of front seat belt. [W3A0].>
5) Remove the two TORXTbolts and then detach
side airbag sensor while disconnecting connector.

S5M0308
6) Install in the reverse order of removal.
13
[W7A0]5-5SERVICE PROCEDURE
7. Side Airbag Sensor

9. Front Sub Sensor
A: REMOVAL AND INSTALLATION
CAUTION:
IIf the front end of the vehicle body is dam-
aged by a collision, be sure to check the left
and right front sub sensors, even if the airbag
was not inflated. If any damage to the sensor or
any deformation of the sensor mount is found,
replace with a new genuine part.
G5M0291
IWhen painting or performing sheet metal
work on the front part of vehicle body, includ-
ing the front wheel apron, front fender and
front side frame, take utmost care not to apply
dryer heat, painting mist, or the flame of the
welding burner directly to the front sub sen-
sors and wire harness of the airbag system.
G5M0310
1. FRONT SUB SENSOR HARNESS
1) Turn ignition switch off.
2) Disconnect ground cable from battery and wait
for at least 20 seconds before starting work.3) Remove front side sill cover and then discon-
nect front sub sensor connector. [M2F5].>
B5M0517
4) Remove front wheel and mud guard.
5) Disconnect connector from front sub sensor
assembly.
S5M0335
6) Remove wiring harness clips.
G5M0315
7) Remove grommet and then detach front sub
sensor harness.
G5M0316
8) Install in the reverse order of removal.
16
5-5[W9A0]SERVICE PROCEDURE
9. Front Sub Sensor

2. FRONT SUB SENSOR ASSEMBLY
1) Turn ignition switch off.
2) Disconnect ground cable from battery and wait
for at least 20 seconds before starting work.
3) Remove front wheel and mud guard.
4) Disconnect connector from front sub sensor
assembly.
S5M0335
5) Remove front sub sensor.
S5M0336
6) Install in the reverse order of removal.
17
[W9A2]5-5SERVICE PROCEDURE
9. Front Sub Sensor