1999 MITSUBISHI LANCER EVOLUTION VI sensor

MPI – Troubleshooting13-57
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
14Throttle
position
Ignition switch: ONSet to idle position300 – 1,000 mVCode No.
14
13-9
position
sensor
Gradually openIncreases in
proportion to
throttle opening
angle
14
Open fully4,500 – 5,500 mV
16Power
supply
voltageIgnition switch: ONSystem voltageProcedure
No. 2413-35
18Cranking
signal Ignition switch: ONEngine: StoppedOFFProcedure
No. 2713-38
g
(ignition
switch-ST)Engine: CrankingON
21Engine
coolant
temperature
sensor
Ignition switch: ON or
with engine runningWhen engine
coolant temperature
is –20C–20CCode No.
2113-10
sensor
When engine
coolant temperature
is 0C0C
When engine
coolant temperature
is 20C20C
When engine
coolant temperature
is 40C40C
When engine
coolant temperature
is 80C80C

MPI – Troubleshooting13-58
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
22Crank angle
sensor
Engine: Cranking

Tachometer:
ConnectedCompare the engine
speed readings on
the tachometer and
the MUT-II.Accord––

Engine: Idling

Idle position
switch: ONWhen engine
coolant temperature
is –20C1,300 – 1,500 rpm
When engine
coolant temperature
is 0C1,300 – 1,500 rpm
When engine
coolant temperature
is 20C1,300 – 1,500 rpm
When engine
coolant temperature
is 40C1,150 – 1,350 rpm
When engine
coolant temperature
is 80C750 – 950 rpm
25Barometric
pressure
Ignition switch: ONAt altitude of 0 m101 kPaCode No.
25
13-14
pressure
sensor
At altitude of 600 m95 kPa
25
At altitude of 1,200 m88 kPa
At altitude of 1,800 m81 kPa
26Idle position
switchIgnition switch: ON
Check by operating
accelerator pedal
Throttle valve:
Set to idle positionONProcedure
No. 2613-38
accelerator pedal
repeatedly.)Throttle valve:
Slightly openOFF*
27Power
steering fluid
pressure
Engine: IdlingSteering wheel
stationaryOFFProcedure
No. 2813-39
pressure
switchSteering wheel
turningON
28A/C switchEngine: Idling
(when A/C switch isA/C switch: OFFOFFProcedure
No. 2913-39
(Ctc
ON, A/C compressor
should be operating.)A/C switch: ONON
NOTE
*: The idle position switch normally turns off when the voltage of the throttle position sensor is 50 –
100 mV higher than the voltage at the idle position. If the throttle position switch turns back on
after the throttle valve has opened, the idle position switch and the throttle position sensor need
to be adjusted.

MPI – Troubleshooting13-63
ENGINE-ECU INSPECTION
TERMINAL VOLTAGES
Engine ECU connector
Terminal
No.Check itemCheck condition (Engine condition)Normal condition
1No.1 injectorWhile engine is idling after having been warmed up,
suddenly depress the accelerator pedal
Momentarily drops
slightlyfrom 1114V
14No.2 injector
suddenly depress the accelerator pedal.slightly from 11 – 14 V.
2No.3 injector
15No.4 injector
3Fuel pressure control
valve
Ignition switch: ONSystem voltage
valve
Engine: Cranking to idling (within about two minutes)0 – 3 V to sytem
voltage
4Stepper motor coil (A1)Engine: Immediately after engine has been started
f
or warming up
Changes repeatedly
f
rom system voltage
17Stepper motor coil (A2)
for warming upfrom system voltage
to 0 – 6 V and from 0
6 V to system5Stepper motor coil (B1)– 6 V to system
voltage.
18Stepper motor coil (B2)
6Secondary air control
solenoid valveIgnition switch: ONSystem voltage
8Fuel pump relayIgnition switch: ONSystem voltage
Engine: Idling0 – 3 V
10Power transistor unit
(A)Engine speed: 3,000 r/min0.3 – 3.0 V
23Power transistor unit
(B)
11Wastegate solenoid
valve
Ignition switch: ONSystem voltage
valve
Engine: At idle after having been warmed up (when
premium gasoline is used)0 – 3 V
12Power supplyIgnition switch: ONSystem voltage
25
19Air flow sensor reset
signal
Engine: Idling0 – 1 V
signal
Engine speed: 3,000 r/min6 – 9 V
20Fan motor relay (HI)
Fan not operating (coolant temperature: 90C or
below)System voltage
Fan at high speed (coolant temperature: 105C or
above)0 – 3 V

MPI – Troubleshooting13-65
Terminal
No.Normal condition Check condition (Engine condition) Check item
41Alternator FR terminal
Engine: Warm, idle (radiator fan: OFF)

Headlamp: OFF to ON

Brake lamp: OFF to ON

Rear defogger switch: OFF to ONVoltage drops by 0.2 –
3.5 V.
45A/C switchEngine: Idle speedTurn the A/C switch OFF0 – 3 V
Turn the A/C switch ON
(A/C compressor is oper-
ating)System voltage
60Oxygen sensor heater

Engine: Idling0 – 3 V

Engine speed: 5,000 r/minSystem voltage
71Ignition switch-STEngine: Cranking8 V or more
72Intake air temperature
sensorIgnition switch: ONWhen intake air tempera-
ture is 0C3.2 – 3.8 V
When intake air tempera-
ture is 20C2.3 – 2.9 V
When intake air tempera-
ture is 40C1.5 – 2.1 V
When intake air tempera-
ture is 80C0.4 – 1.0 V
76Oxygen sensorEngine: Running at 2,000 r/min after having been
warmed up (Check using a digital type voltmeter)0 ↔ 0.8 V
(Changes repeatedly)
80Backup power supplyIgnition switch: OFFSystem voltage
81Sensor impressed
voltageIgnition switch: ON4.5 – 5.5 V
82Ignition switch-IGIgnition switch: ONSystem voltage
83Engine coolant
temperature sensorIgnition switch: ONWhen engine coolant
temperature is 0C3.2 – 3.8 V
When engine coolant
temperature is 20C2.3 – 2.9 V
When engine coolant
temperature is 40C1.3 – 1.9 V
When engine coolant
temperature is 80C0.3 – 0.9 V
84Throttle position sensorIgnition switch: ONSet throttle valve to idle
position0.3 – 1.0 V
Fully open throttle valve4.5 – 5.5 V
85Barometric pressure
sensor
Ignition switch: ONWhen altitude is 0 m3.7 – 4.3 V
sensor
When altitude is 1,200 m3.2 – 3.8 V
86Vehicle speed sensor
Ignition switch: ON

Move the vehicle slowly forward0 ↔ 5 V
(Changes repeatedly)

MPI – Troubleshooting13-66
Terminal
No.Normal condition Check condition (Engine condition) Check item
87Idle position switchIgnition switch: ONSet throttle valve to idle
position0 – 1 V
Slightly open throttle
valve4 V or more
88Camshaft position
sensor
Engine: Cranking0.4 – 3.0 V
sensor
Engine: Idle speed0.5 – 2.0 V
89Crank angle sensorEngine: Cranking0.4 – 4.0 V
Engine: Idle speed1.5 – 2.5 V
90Air flow sensorEngine: Idle speed2.2 – 3.2 V
Engine speed: 2,000 r/min

MPI – Troubleshooting13-67
RESISTANCE AND CONTINUITY BETWEEN HARNESS SIDE CONNECTORS AND TERMINALS
Engine-ECU Harness Side Connector Terminal Arrangement
Terminal No.Inspection itemNormal condition (Check condition)
1 – 12No.1 injector2 – 3 Ω (At 20C)
14 – 12No.2 injector
2 – 12No.3 injector
15 – 12No.4 injector
3 – 12Fuel pressure control valve28 – 36 Ω (At 20C)
4 – 12Stepper motor coil (A1)28 – 33 Ω (At 20C)
17 – 12Stepper motor coil (A2)
5 – 12Stepper motor coil (B1)
18 – 12Stepper motor coil (B2)
6 – 12Secondary air control solenoid valve28 – 36 Ω (At 20C)
11 – 12Wastegate solenoid valve62 – 74 Ω (At 20C)
60 – 12Oxygen sensor heater
11 – 18 Ω (at 20C)
13 – Body earthEngine-ECU earthContinuity established (0 Ω)
26 – Body earth
72 – 92Intake air temperature sensor5.3 – 6.7 kΩ (When intake air temperature is 0C)
2.3 – 3.0 kΩ (When intake air temperature is 20C)
1.0 – 1.5 kΩ (When intake air temperature is 40C)
0.30 – 0.42 kΩ (When intake air temperature is 80C)
74 – 77High temperature sensor3 Ω or less
83 – 92Engine coolant temperature sensor5.1 – 6.5 kΩ (When coolant temperature is 0C)
2.1 – 2.7 kΩ (When coolant temperature is 20C)
0.9 – 1.3 kΩ (When coolant temperature is 40C)
0.26 – 0.36 kΩ (When coolant temperature is 80C)
87 – 92Idle position switchContinuity established (when throttle valve is at idle
position)
No continuity (when throttle valve is slightly open)
91 – Body earth–Continuity established

FRONT AXLE – General / Axle Hub and Knuckle 26-1
GROUP 26
FRONT AXLE
GENERAL
OUTLINE OF CHANGE

The installation method of the ball joint between the knuckle and the lower arm has been changed,
and accordingly the removal and installation procedures of the axle hub and the knuckle have been
revised.
AXLE HUB AND KNUCKLE
REMOVAL AND INSTALLATION
Caution
(1) For vehicles with AYC, be careful when handling the pole piece at the tip of the speed sensor so as
not to damage it by striking against other parts.
(2) For vehicles with AYC, be careful not to damage the rotors installed to B.J. outer race during removal
and installation of the drive shaft.
Post-installation Operation

Check the Dust Cover for Cracks or Damage by
Pushing it with Finger.
1
23
4 5 6 7
8
12 1415
1388 Nm 108 – 127 Nm
90 – 110 Nm
15 – 33 Nm177 – 275 Nm 25 Nm
25 Nm
9 Nm
103 Nm
74 –87
Nm
11 910
1610
11
Ball joint kit
Removal steps
1. Front speed sensor AYC>
A2. Caliper assembly
3. Brake disc
4. Split pin
BA5. Drive shaft nut
6. Front hub assembly
7. Dust shield
8. Connection for lower arm ball joint
9. Connection bolt for lower arm joint10. Lower arm ball joint
11. Dust cover
12. Split pin
C13. Connection for tie rod end
D14. Front drive shaft
15. Front strut mounting bolt
16. Knuckle
NOTE
Follow the conventional procedures for removal
and installation service points.

27-1
REAR AXLE
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . .
LUBRICANT 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 3. . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 4. . . . . . . . . . . . .
ON-VEHICLE SERVICE
31. . . . . . . . . . . . . . .
Rear Axle Total Backlash Check 31. . . . . . . . . . .
Gear Oil Level Check 31. . . . . . . . . . . . . . . . . . . .
Gear Oil Change 32. . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Level Check 33. . . . . . . . . . . . . . . . . . . . . . . . Bleeding 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AYC Operation Check 34. . . . . . . . . . . . . . . . . . . .
Hydraulic Pressure Check 35. . . . . . . . . . . . . . . . .
Differential Carrier Oil Seal
Replacement 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Speed Sensor Output Voltage
Measurement 37. . . . .
Action When Battery Runs Out 38. . . . . . . . . . . .
HYDRAULIC UNIT
39. . . . . . . . . . . . . . .
SENSOR RELAY
41. . . . . . . . . . . . . . .
AYC-ECU 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .