1999 MITSUBISHI LANCER EVOLUTION VI ignition

MPI – Troubleshooting13-48
INSPECTION PROCEDURE 39
MUT-II: Check if uncomplete combustion occurs.
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
MUT-II Actuator test
07 Fuel pump (Refer to P.13-61.)NGCheck the fuel pump system.
(Refer to P.13-36, INSPECTION PROCEDURE 25.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13-10, INSPECTION PROCEDURES FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
18 Ignition switch-ST (Refer to P.13-57.)NGCheck the ignition switch-ST system.
(Refer to P.13-38, INSPECTION PROCEDURE 27.)
INSPECTION PROCEDURE 40
Check if hunting occurs.
Clean the throttle body.
Check and adjust the fixed SAS. (Refer to P.13-30.)*
Check trouble symptom.
NG
Inspect the intake of air into the air intake system

Broken intake manifold gasket

Broken air intake hose

Broken vacuum hose

Positive crankcase ventilation valve does not operate.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – Troubleshooting13-53
INSPECTION PROCEDURE 45
Check the engine-ECU power supply and earth circuit.
Measure at the engine-ECU connectors, B-59, B-60, B-62.

Disconnect the connector and measure at the harness side
1. Voltage between 82 and earth (Ignition switch: ON)
OK:System voltage
2. Voltage between 38 and earth
OK:System voltage
3. Voltage between 12, 25 and earth (Ignition switch: ON)
OK:System voltage (when the terminal 38 is earthed)
4. Continuity between 13, 26 and earth
OK:Continuity
5. Voltage between 80 and earth
OK:System voltage1. NGCheck the following
connectors: B-65, B-76NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire
between engine-ECU and
ignition switch connector.NG
Repair
OK
Check the ignition switch. (Refer to GROUP 54.)
2, 3. NG
4. NG
Check the harness wire between engine-ECU and earth, and repair
if necessary.
5. NG
OK
Check the following
connectors:
B-59, B-60, B-62NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
Check the following connectors:
B-65, B-49, B-75, B-73NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between engine-ECU and battery, and
repair if necessary.
Check the harness wire between engine-ECU and control relay
connector, and repair if necessary.
INSPECTION PROCEDURE 46
Check fuel pump circuit.
Measure at the fuel pump connector D-18.

Disconnect the connector and measure at the harness side.

Continuity between 1 and earth
OK:ContinuityNGCheck the following connector:
D-04NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between fuel pump and earth, and repair
if necessary.
OK
Check the following connectors: D-04, B-64NG
Repair OKCheck trouble symptom.
NG
Check the harness wire between terminal for fuel pump drive and
fuel pump connector.NG
Repair
OK
Replace the fuel pump.

MPI – Troubleshooting13-54
INSPECTION PROCEDURE 46
Check fuel pump circuit.
Measure at the fuel pump relay connector D-18.

Disconnect the connector and measure at the harness side.

Continuity between 1 and earth
OK:ContinuityNGCheck the following connector:
D-04NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between fuel pump and earth, and repair
if necessary.
OK
Check the following connectors: A-123, B-64, D-18, D-32NG
Repair OKCheck trouble symptom.
NG
Check the harness wire between fuel pump and fuel pump relay
No.2 connector.NG
Repair
OK
Replace the fuel pump.
INSPECTION PROCEDURE 47
Check the fuel pump drive control circuit.
NG
Check the harness wire between the fuel pump relay and engine-
ECU connector.
OK
Check trouble symptom.
OK
Check trouble symptom.
NG
Check the harness wire
between fuel pump relay
and ignition switch con-
nector.NG
Repair
OK
Check the ignition switch. (Refer to GROUP 54.)OK
Check trouble symptom.
NG
Replace the engine-ECU.
NG
Repair
OK
Check the following connector: B-59
OK
Measure at the engine-ECU connector B-59.

Disconnect the connector and measure at the harness side.

Voltage between 8 and earth (Ignition switch: ON)
OK:System voltageNG
Measure at the fuel pump relay connector B-28.

Disconnect the connector and measure at the harness side.

Voltage between 3, 4 and earth (Ignition switch: ON)
OK:System voltageNGCheck the following
connectors: B-65, B-76NG
Repair
Check the following
connector: B-28NG
Repair

MPI – TroubleshootingMPI – Troubleshooting13-55
INSPECTION PROCEDURE 48
Check air flow sensor control circuit.
2, 3. NGCheck the following
connector: B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire
between the engine-ECU
and air flow sensor con-
nector.NG
Repair
OK
Replace the engine-ECU.
OK
Check trouble symptom.
NG
Replace the air flow sensor.
NG
Repair
OK
Check the following connector: A-25
Measure at the air flow sensor connector A-25.

Disconnect the connector and measure at the harness side.
1. Voltage between 4 and earth (Ignition switch: ON)
OK:System voltage
2. Voltage between 3 and earth (Ignition switch: ON)
OK:4.8–5.2 V
3. Continuity between 5 and earth
OK:Continuity1. NGCheck the harness wire between the air flow sensor and control
relay connector, and repair if necessary.
INSPECTION PROCEDURE 49
Check throttle position sensor output circuit.
Measure at the engine-ECU connector B-62.

Connect the connector.

Voltage between 84 and earth (Ignition switch: ON)
OK:0.3–1.0 V (Throttle valve at idle position)
4.5–5.5 V (Throttle valve fully open)NGCheck the following
connector: B-62NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
OK
Check the harness wire between engine-ECU and throttle position
sensor connector, and repair if necessary.
INSPECTION PROCEDURE 50
Check injector control circuit.
Measure at the engine-ECU connector B-59.

Disconnect the connector and measure at the harness side.

Voltage between 1, 2, 14, 15 and earth (Ignition switch: ON)
OK:System voltageNGCheck the following
connectors:
A-53, A-54, A-55, A-56NG
Repair
OK
Check trouble symptom.
NG
Check the harness between engine-ECU and injector connector,
and repair if necessary.
OK
Check the following connector: B-59
OK
Check trouble symptom.
NG
Replace the engine-ECU.NG
Repair

MPI – Troubleshooting13-56
DATA LIST REFERENCE TABLE
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
11Oxygen
sensorEngine:After having
warmed up
Air/fuel mixture is
made leaner when de-
When at 4,000 r/min,
engine is suddenly
decelerated200 mV or lessProcedure
No. 3113-42
made leaner when de-
celerating, and is made
richer when racing.
When engine is
suddenly raced600 – 1,000 mV
Engine:After having
warmed up
The oxygen sensor
si
gnal is used to check
Engine is idling400 mV or less
(Changes)
signal is used to check
the air/fuel mixture
ratio, and control
condition is also
checked by the ECU.2,500 r/min600 – 1,000 mV
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling17 – 43 Hz––
sensor
TION-IV>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min46 – 86 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling12 – 38 Hz––
sensor
TION-V, VI>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min36 – 76 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
13Intake air
temperature
sensor
Ignition switch: ON or
with engine runningWhen intake air
temperature is –20C–20CCode No.
1313-9
sensorWhen intake air
temperature is 0C0C
When intake air
temperature is 20C20C
When intake air
temperature is 40C40C
When intake air
temperature is 80C80C
NOTE
*: In a new vehicle [driven approximately 500 km or less], the air flow sensor output frequency is sometimes
10% higher than the standard frequency.

MPI – Troubleshooting13-57
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
14Throttle
position
Ignition switch: ONSet to idle position300 – 1,000 mVCode No.
14
13-9
position
sensor
Gradually openIncreases in
proportion to
throttle opening
angle
14
Open fully4,500 – 5,500 mV
16Power
supply
voltageIgnition switch: ONSystem voltageProcedure
No. 2413-35
18Cranking
signal Ignition switch: ONEngine: StoppedOFFProcedure
No. 2713-38
g
(ignition
switch-ST)Engine: CrankingON
21Engine
coolant
temperature
sensor
Ignition switch: ON or
with engine runningWhen engine
coolant temperature
is –20C–20CCode No.
2113-10
sensor
When engine
coolant temperature
is 0C0C
When engine
coolant temperature
is 20C20C
When engine
coolant temperature
is 40C40C
When engine
coolant temperature
is 80C80C

MPI – Troubleshooting13-58
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
22Crank angle
sensor
Engine: Cranking

Tachometer:
ConnectedCompare the engine
speed readings on
the tachometer and
the MUT-II.Accord––

Engine: Idling

Idle position
switch: ONWhen engine
coolant temperature
is –20C1,300 – 1,500 rpm
When engine
coolant temperature
is 0C1,300 – 1,500 rpm
When engine
coolant temperature
is 20C1,300 – 1,500 rpm
When engine
coolant temperature
is 40C1,150 – 1,350 rpm
When engine
coolant temperature
is 80C750 – 950 rpm
25Barometric
pressure
Ignition switch: ONAt altitude of 0 m101 kPaCode No.
25
13-14
pressure
sensor
At altitude of 600 m95 kPa
25
At altitude of 1,200 m88 kPa
At altitude of 1,800 m81 kPa
26Idle position
switchIgnition switch: ON
Check by operating
accelerator pedal
Throttle valve:
Set to idle positionONProcedure
No. 2613-38
accelerator pedal
repeatedly.)Throttle valve:
Slightly openOFF*
27Power
steering fluid
pressure
Engine: IdlingSteering wheel
stationaryOFFProcedure
No. 2813-39
pressure
switchSteering wheel
turningON
28A/C switchEngine: Idling
(when A/C switch isA/C switch: OFFOFFProcedure
No. 2913-39
(Ctc
ON, A/C compressor
should be operating.)A/C switch: ONON
NOTE
*: The idle position switch normally turns off when the voltage of the throttle position sensor is 50 –
100 mV higher than the voltage at the idle position. If the throttle position switch turns back on
after the throttle valve has opened, the idle position switch and the throttle position sensor need
to be adjusted.

MPI – Troubleshooting13-60
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
44Ignition coils
and power
transistors
having warmed up

Timing lamp is set.
(The timing lampEngine is idling3ATDC –
13BTDC––
TION-IV>
(tgp
is set in order to
check actual
ignition timing.)2,500 r/min24 – 44BTDC
44Ignition coils
and power
transistors

Engine: After
having warmed up

Timing lamp is set
Engine is idling0 – 13BTDC––
transistors
TION-V, VI>
Timing lamp is set.
2,500 r/min24 – 44BTDC
45ISC
(stepper)
motor
position *

Engine coolant
temperature: 80 –
90C

Lam
ps, electric
A/C switch: OFF2 – 25 steps––
position
Lamps, electric
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T :
P range)
Idl iti
A/C switch:
OFF → ONIncreases by
10 – 70 steps
g)

Idle position
switch: ON

Engine: Idling

When A/C switch
is ON, A/C
compressor should
be operating
A/C switch: OFF

Select lever:
N range →
D rangeIncreases by
5 – 50 steps
49A/C relayEngine: After having
warmed up/Engine is
idlingA/C switch: OFFOFF (Compressor
clutch is not
operating)Procedure
No. 2913-39
A/C switch: ONON (Compressor
clutch is
operating)
NOTE
*: In a new vehicle [driven approximately 500 km or less], the stepper motor has sometimes 30 steps
greater than the standard value.
Caution
When shifting the select lever to D range, the brakes should be applied so that the vehicle does
not move forward.