1999 MITSUBISHI LANCER EVOLUTION VI heater

– Heater Unit and Blower Unit HEATER AND MANUAL
AIR CONDITIONER55-18
HEATER UNIT AND BLOWER UNIT

REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation

Engine Coolant Draining and Refilling

Air Cleaner Cover and Hose Removal and
Installation

Floor Console and Instrument Panel Removal and
Installation

Rear Seat Heater Duct Removal and Installation
(Refer to P.55-31.)
1
34
5
6
2 7 8
9 1011
Removal steps
1. Center reinforcement RH
2. Heater control assembly
3. Center reinforcement LH
4. Center ventilation duct
5. Foot distribution duct
6. Joint duct7. Blower unit
8. Heater hose
9. Heater unit
10. Heater core support
11. Heater core

– Heater Unit, Cooling and Blower Unit HEATER AND MANUAL
AIR CONDITIONER55-19
HEATER UNIT, COOLING AND BLOWER UNIT

REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation

Engine Coolant Draining and Refilling

Discharging and Charging of Refrigerant
(Refer to P.55-6.)

Air Cleaner Cover and Hose Removal and
Installation

Floor Console and Instrument Panel Removal and
Installation

Rear Seat Heater Duct Removal and Installation
(Refer to P.55-31.)
1
34
5 6
2 7
8 9
10 1112
Piping connection
O-ring
A/C Compressor oil: SUN PAG 56
Removal steps
1. Center reinforcement RH
2. Heater control assembly
3. Center reinforcement LH
4. Center ventilation duct
5. Foot distribution duct
6. Drain hose
A7. Connection between cooling unit
and refrigerant line8. Cooling and blower unit
9. Heater hose
10. Heater unit
11. Heater core support
12. Heater core
REMOVAL SERVICE POINT
AREMOVAL OF REFRIGERANT LINE FROM
COOLING UNIT
Plug the open end of the removed hose and the opening
in the cooling unit to prevent entry of dust and foreign
substances.
Caution
Compressor oil and the receiver are highly
moisture-absorptive.
Do not use plugs allowing ventilation.

– Blower Motor Assembly, Resistor and Evaporator HEATER AND MANUAL
AIR CONDITIONER55-20
BLOWER MOTOR ASSEMBLY, RESISTOR AND EVAPORATOR
REMOVAL AND INSTALLATION
4
6 2
1 5
3
7
Piping connection
O-ring
A/C Compressor oil: SUN PAG 56
Blower motor assembly removal
steps
1. Under cover

2. Blower motor assembly
Resistor removal steps
1. Under cover


Glove box, glove box frame
3. ResistorEvaporator removal steps


Discharging and Charging of
refrigerant (Refer to P.55-6.)

Glove box, glove box frame
4. Drain hose
A5. Connection between evaporator
and refrigerant line
B6. Case cover
B7. Evaporator
REMOVAL SERVICE POINT
AREMOVAL OF REFRIGERANT LINE FROM
EVAPORATOR
Plug the open end of the removed hose and the opening
in the evaporator to prevent entry of dust and foreign
substances.
Caution
Compressor oil and the receiver are highly
moisture-absorptive.
Do not use plugs allowing ventilation.

– Blower Motor Assembly, Resistor and Evaporator HEATER AND MANUAL
AIR CONDITIONER55-21
BCASE COVER, EVAPORATOR REMOVAL
The evaporator, which has been installed in a factory, has
no case cover. Follow the steps below to remove that
evaporator.
1. Cut the case along the shown line to remove the cooling
and blower unit.
2. Remove the air thermo sensor from the evaporator, and
then remove the evaporator towards you, being careful
not to damage its core.
INSPECTION
BLOWER MOTOR CHECK
When battery voltage is applied between the terminals, check
that the motor operates. Also, check that there is no abnormal
noise.
RESISTOR CHECK
Use a circuit tester to measure the resistance between the
terminals as indicated below. Check that the measured value
is at the standard value.
Standard value:
Measurement terminalStandard value Ω
Between terminals 3 and 22.81 ± 10%
Between terminals 3 and 41.28 ± 10%
Between terminals 3 and 10.33 ± 10%
Cut line
Evaporator

– Blower Motor Assembly, Resistor and Evaporator HEATER AND MANUAL
AIR CONDITIONER55-22
AIR THERMO-SENSOR CHECK
Measure the resistance between the sensor terminals in two
or more different temperature conditions. The resistance
values must conform to the values shown in the graph.
NOTE
The temperatures at checking must be within the range shown
in the characteristic curve.kΩ
Temperature
Resistance
°C 0
–10 0 10 20 30 40 5 10 15 20

– Compressor and Tension Pulley HEATER AND MANUAL
AIR CONDITIONER55-23
COMPRESSOR AND TENSION PULLEY
REMOVAL AND INSTALLATION
Pre-removal Operation

Discharging of Refrigerant (Refer to P.55-6.)Post-installation Operation

Drive Belt Tension Adjustment

Charging of Refrigerant (Refer to P.55-6.)
4
2
1 53
Piping connection
O-ring
A/C Compressor oil: SUN PAG 56
59 – 69 Nm
Removal steps
A1. Drive belt
2. Idler pulley
B3. Suction hose and discharge hose
connection
CA4. Compressor
5. Compressor bracket

– Compressor and Tension Pulley HEATER AND MANUAL
AIR CONDITIONER55-24
REMOVAL SERVICE POINTS
ADRIVE BELT REMOVAL
1. Align the hole in the auto-tensioner bracket with that in
the arm and insert a screwdriver into the holes.
2. Remove the drive belt.
BSUCTION HOSE, DISCHARGE HOSE
DISCONNECTION
Plug the disconnected hose and the compressor nipple not
to let foreign matter get into them.
Caution
Seal the hoses completely, otherwise the compressor
oil and receiver will absorb water vapour easily.
CCOMPRESSOR REMOVAL
When doing this work, be careful not to spill the compressor
oil.
Auto-tensioner
Hole in
arm
Hole in
bracket
Screwdriver (+)

– Compressor and Tension Pulley HEATER AND MANUAL
AIR CONDITIONER55-25
INSTALLATION SERVICE POINT
ACOMPRESSOR INSTALLATION
If a new compressor is installed, first adjust the amount of
oil according to the procedures described below, and then
install the compressor.
1. Measure the amount (X m
) of oil within the removed
compressor.
2. Drain (from the new compressor) the amount of oil
calculated according to the following formula, and then
install the new compressor.
New compressor oil amount
120 to 140 m
– X m
= Y m

NOTE
(1)“120 to 140 ml” is the amount of oil filled in a new
compressor.
(2) Y m
indicates the amount of oil in the refrigerant
line, the condenser, the cooling unit etc.
INSPECTION
REFRIGERANT-TEMPERATURE SWITCH SIMPLE
CHECK
When the A/C is off, check that there is continuity between
the refrigerant-temperature switch terminals. If no, replace
the compressor assembly.
COMPRESSOR MAGNETIC CLUTCH OPERATION
INSPECTION
Connect the battery (+) terminal to the compressor side
terminal, and earth the battery (–) terminal to the body of
the compressor. The condition is normal if the sound of the
magnetic clutch (click) can be heard.AView A
Refrigerant temperature
switch terminal