1999 MITSUBISHI LANCER EVOLUTION VI ABS

REAR AXLE – On-vehicle Service 27-38
Waveform Observation Points
SymptomProbable causeAction
Waveform amplitude is too small, or no
waveform.Defective wheel speed sensorReplace sensor.
Waveform amplitude varies greatly. (No
problem ifthe smallest amplitude is 100
Excessive axle hub lateral and radial runoutReplace hub.
problem if the smallest amplitude is 100
mV or more)Poor AYC-ECU groundingRepair.
Noise on waveform or disturbed
waveform
Open-circuited sensorReplace sensor.
waveform
Open-circuited harnessRepair harness.
Improperly mounted wheel speed sensorCorrect sensor installation.
Missing or collapsed ABS rotor toothReplace ABS rotor.
Caution
Since the wheel speed sensor cable follows the movement of the front or rear suspension, it
may be open-circuited only when the vehicle is run on rough roads and not on ordinary road.
The wheel speed sensor output voltage waveform should therefore be checked also by rocking
the sensor harness so that driving on rough roads may be simulated.
ACTION WHEN BATTERY RUNS OUT
When the engine is started using a booster cable where the
battery has completely run down and you attempt to start
the vehicle without waiting for the battery to recover a certain
charge, the engine can misfire and you just cannot start to
move it. In such cases, charge the battery sufficiently; or,
remove the AYC fusible link from the engine compartment
relay box to make AYC inactive before attempting to start
the vehicle. When the fusible link is removed, the AYC warning
lamp lights up. After the battery has been recharged, fit the
fusible link back again and start the engine to ensure that
the AYC warning lamp is off.AYC fusible link

– Heater Unit, Cooling and Blower Unit HEATER AND MANUAL
AIR CONDITIONER55-19
HEATER UNIT, COOLING AND BLOWER UNIT

REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation

Engine Coolant Draining and Refilling

Discharging and Charging of Refrigerant
(Refer to P.55-6.)

Air Cleaner Cover and Hose Removal and
Installation

Floor Console and Instrument Panel Removal and
Installation

Rear Seat Heater Duct Removal and Installation
(Refer to P.55-31.)
1
34
5 6
2 7
8 9
10 1112
Piping connection
O-ring
A/C Compressor oil: SUN PAG 56
Removal steps
1. Center reinforcement RH
2. Heater control assembly
3. Center reinforcement LH
4. Center ventilation duct
5. Foot distribution duct
6. Drain hose
A7. Connection between cooling unit
and refrigerant line8. Cooling and blower unit
9. Heater hose
10. Heater unit
11. Heater core support
12. Heater core
REMOVAL SERVICE POINT
AREMOVAL OF REFRIGERANT LINE FROM
COOLING UNIT
Plug the open end of the removed hose and the opening
in the cooling unit to prevent entry of dust and foreign
substances.
Caution
Compressor oil and the receiver are highly
moisture-absorptive.
Do not use plugs allowing ventilation.

– Blower Motor Assembly, Resistor and Evaporator HEATER AND MANUAL
AIR CONDITIONER55-20
BLOWER MOTOR ASSEMBLY, RESISTOR AND EVAPORATOR
REMOVAL AND INSTALLATION
4
6 2
1 5
3
7
Piping connection
O-ring
A/C Compressor oil: SUN PAG 56
Blower motor assembly removal
steps
1. Under cover

2. Blower motor assembly
Resistor removal steps
1. Under cover


Glove box, glove box frame
3. ResistorEvaporator removal steps


Discharging and Charging of
refrigerant (Refer to P.55-6.)

Glove box, glove box frame
4. Drain hose
A5. Connection between evaporator
and refrigerant line
B6. Case cover
B7. Evaporator
REMOVAL SERVICE POINT
AREMOVAL OF REFRIGERANT LINE FROM
EVAPORATOR
Plug the open end of the removed hose and the opening
in the evaporator to prevent entry of dust and foreign
substances.
Caution
Compressor oil and the receiver are highly
moisture-absorptive.
Do not use plugs allowing ventilation.

– Compressor and Tension Pulley HEATER AND MANUAL
AIR CONDITIONER55-24
REMOVAL SERVICE POINTS
ADRIVE BELT REMOVAL
1. Align the hole in the auto-tensioner bracket with that in
the arm and insert a screwdriver into the holes.
2. Remove the drive belt.
BSUCTION HOSE, DISCHARGE HOSE
DISCONNECTION
Plug the disconnected hose and the compressor nipple not
to let foreign matter get into them.
Caution
Seal the hoses completely, otherwise the compressor
oil and receiver will absorb water vapour easily.
CCOMPRESSOR REMOVAL
When doing this work, be careful not to spill the compressor
oil.
Auto-tensioner
Hole in
arm
Hole in
bracket
Screwdriver (+)

– Condenser and Condenser Fan HEATER AND MANUAL
AIR CONDITIONER55-29
REMOVAL SERVICE POINTS
AFAN MOTOR AND SHROUD ASSEMBLY
REMOVAL
Remove the clamp bolt of the power steering oil cooler pipe.
Remove the fan motor and shroud assembly while pulling
the power steering oil cooler pipe toward you.
BDISCHARGE HOSE / LIQUID PIPE A
DISCONNECTION
Plug the open end of the disconnected hose and the opening
in the cooling unit not to let foreign matter get into them.
Caution
Seal the hoses completely, otherwise the compressor
oil and receiver will absorb water vapour easily.
CCONDENSER REMOVAL
Move the radiator to the engine side and then lift up the
condenser to remove it.
INSPECTION
CONDENSER FAN MOTOR CHECK
Battery connection terminalCondenser fan operation
12
Rotate
Condenser

– Refrigerant Line HEATER AND MANUAL
AIR CONDITIONER55-30
REFRIGERANT LINE
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation

Discharging and Charging of Refrigerant
(Refer to P.55-6.)

Air Cleaner Case and Hose Removal and
Installation
O-ring
Piping connection
A/C Compressor oil: SUN PAG 56
4 62
1 5
3
7 8
9
10
3
A1. Liquid pipe B
2. Clip
3. Clamp
A4. Suction hose assembly
A5. Liquid pipe A6. Clip
A7. Receiver
8. Dual pressure switch
9. Receiver bracket
A10. Discharge hose
AHOSE / PIPE DISCONNECTION
Plug the open end of the disconnected hose and the opening
in the cooling unit not to let foreign matter get into them.
Caution
Seal the hoses completely, otherwise the compressor
oil and receiver will absorb water vapour easily.

C-2
STOP LAMP 51. . . . . . . . . . . . . . . . . . . . . . . . . .
BACK-UP LAMP 52. . . . . . . . . . . . . . . . . . . . . . .
METER AND GAUGE 54. . . . . . . . . . . . . . . . . .
FUEL WARNING LAMP 56. . . . . . . . . . . . . . . .
BRAKE WARNING LAMP 56. . . . . . . . . . . . . .
OIL PRESSURE WARNING LAMP 57. . . . . .
SEAT BELT WARNING LAMP 57. . . . . . . . . .
CENTRAL DOOR LOCKING SYSTEM 58. .
Without Keyless Entry System 58. . . . . . . . . . . .
With Keyless Entry System 60. . . . . . . . . . . . . . .
HEATER AND AIR CONDITIONER 64. . . . . .
FULL-AUTO AIR CONDITIONER 70. . . . . . . .
WINDSHIELD WIPER AND WASHER 78. .
With Intermittent Wiper 78. . . . . . . . . . . . . . . . . . .
REAR WIPER AND WASHER 79. . . . . . . . . .
DEFOGGER AND DOOR MIRROR
HEATER 80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Without Full-Auto Air Conditioner 80. . . . . . . . . .
With Full-Auto Air Conditioner 82. . . . . . . . . . . . .
RADIO 84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Spare Circuit 84. . . . . . . . . . . . . . . . . . . . . .
4 Speaker, 6 Speaker 86. . . . . . . . . . . . . . . . . . . .
KEY REMINDER BUZZER 89. . . . . . . . . . . . . .
ANTI-SKID BRAKING SYSTEM (ABS) 90. .
SUPPLEMENTAL RESTRAINT SYSTEM
(SRS) 96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTIVE YAW CONTROL SYSTEM (AYC) 98
INTERCOOLER AND RADIATOR WATER
SPRAY SYSTEM 104. . . . . . . . . . . . . . . . . . . . .

– Engine Compartment WIRING HARNESS
CONFIGURATION DIAGRAMS
Connector
symbol
–01
thru
–50
A
Earth cable
C-4
WIRING HARNESS CONFIGURATION DIAGRAMS
ENGINE COMPARTMENT
A-01 (2-B) Brake fluid level switch
A-03 (1-B) Noise condenser
A-04 (1) Alternator
A-05 (4-GR) Alternator
A-09 (1-B) Starter
A-10 (1) Starter
A-12 (2-B) Fuel pressure solenoid valve
A-16 (4-B) Throttle position sensor
A-18 (6-B) Idle speed control servo
A-19 (3-B) Vehicle speed sensorA-20 (4-B) Windshield wiper motor
A-21 (8-B) Hydraulic unit
A-22 (2-B) Hydraulic unit
A-23 (2-B) Waste gate solenoid valve
A-25 (7-B) Air flow sensor
A-26 (2-B) Front speed sensor (LH) ABS>
A-28 (10-B) Control harness and front harness
combination